Related Manuals for Asus AAEON AIOT-ILND01
Summary of Contents for Asus AAEON AIOT-ILND01
- Page 1 AIOT- ILND01 LoRa Long Range Radio Node Board User’s Manual 1 Last Updated: May 23, 2019...
-
Page 2: Copyright Notice
Copyright Notice This document is copyrighted, 2019. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. - Page 3 Acknowledgements All other product names or trademarks are properties of their respective owners. The publisher and writer of this document make no claim to ownership of these products, nor is any claim implied for products not specifically named in this section. Semtech®, LoRa®, LoRaWAN™, and LoRa Alliance™...
- Page 4 Packing List Before setting up your product, please make sure the following items have been shipped: Item Quantity AIOT-ILND01 Antenna If any of these items are missing or damaged, please contact your distributor or sales representative immediately. Preface...
- Page 5 About this Document This User’s Manual contains all the essential information, such as detailed descriptions and explanations on the product’s hardware and software features (if any), its specifications, dimensions, jumper/connector settings/definitions, and driver installation instructions (if any), to facilitate users in setting up their product. Users may refer to the product page at AAEON.com for the latest version of this document.
- Page 6 Safety Precautions Please read the following safety instructions carefully. It is advised that you keep this manual for future references All cautions and warnings on the device should be noted. Make sure the power source matches the power rating of the device. Position the power cord so that people cannot step on it.
- Page 7 If any of the following situations arises, please the contact our service personnel: Damaged power cord or plug Liquid intrusion to the device iii. Exposure to moisture Device is not working as expected or in a manner as described in this manual The device is dropped or damaged Any obvious signs of damage displayed on the device...
- Page 8 FCC Statement This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.
- Page 9 China RoHS Requirements (CN) 产品中有毒有害物质或元素名称及含量 AAEON Main Board/ Daughter Board/ Backplane 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) 印刷电路板 ○ ○ ○ ○ ○ ○ 及其电子组件 外部信号 ○ ○ ○ ○ ○ ○ 连接器及线材...
- Page 10 China RoHS Requirement (EN) Poisonous or Hazardous Substances or Elements in Products AAEON Main Board/ Daughter Board/ Backplane Poisonous or Hazardous Substances or Elements Hexavalent Polybrominated Polybrominated Component Lead Mercury Cadmium Chromium Biphenyls Diphenyl Ethers (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) PCB &...
-
Page 11: Table Of Contents
Table of Contents Chapter 1 - Product Specifications..................1 Specifications ......................2 Applicatons ....................... 3 Chapter 2 – Hardware Information ..................4 Dimensions ....................... 5 Board and Connectors Layout ................6 List of Connectors ....................8 Connector Pin Assignments .................. 9 2.4.1 MCU Reset Button (SW1) ................ - Page 12 Preface...
-
Page 13: Chapter 1 - Product Specifications
Chapter 1 Chapter 1 - Product Specifications... -
Page 14: Specifications
Specifications System 85 mm x 65 mm Dimensions ST STM32L Semtech SX1276 3 x GROVE connectors I/O Placements 1 x UART1 (RS-232/485) 1 x UART2(TX/RX) 1 x I2C 1 x Temperature & humidity sensor 1 x 3-axis Accelerometer (2G/4G/8G/16G) 1 x micro USB2.0 type B for power supply 1 x JTAG-debug port 1 x battery connector for 2 x 14500 Lithium-ion battery... -
Page 15: Applicatons
Applicatons The AAEON AIOT LoRa Node is a sophisticated and compact LoRa edge device. To provide faster and more flexible communication for industrial LoRa applications, it supports multiple LoRa frequency bands including 868 MHz and 915 MHz, ideal for usage in data collection, aggregation and transmission. The AAEON AIOT LoRa Node has built-in expansion features and can be utilized in energy metering, smart city and agriculture applications. -
Page 16: Chapter 2 - Hardware Information
Chapter 2 Chapter 2 – Hardware Information... -
Page 17: Dimensions
Dimensions Chapter 4 – Installation Guide... -
Page 18: Board And Connectors Layout
Board and Connectors Layout Top Side Chapter 4 – Installation Guide... - Page 19 Bottom Side Chapter 4 – Installation Guide...
-
Page 20: List Of Connectors
List of Connectors Reference Functional Connector Type Designation Description (TF)Push Button MCU Reset Switch.3P .12VDC.50mA.500mohm.Black.SMD.HC button H.PTS-099 (TF)Micro USB Micro USB Conn..5P .90D(F).SMD.AB-type.TRONTEK.TMC106 -USBD05-835 (TF)PIN TCXO_OUT HEADER.2*1P .180D(M).DIP .2.0mm.PINREX.220-96 select -02GB01 (TF)PIN VDD_TCXO HEADER.3*1P .180D(M).DIP .2.0mm.PINREX.220-96 SELECT -03GB01 (TF)WAFER ST-Link BOX.7P .180D(M).SMD.1.0mm.W/Cap.PINREX.710- 73-07TWE6 (TF)PIN... -
Page 21: Connector Pin Assignments
Reference Functional Connector Type Designation Description (TF)Battery BT1/BT2 Battery Holder Holder.2P .180D(F).1*AA.DIP .COMF.BH-311-1P24 (TF)Push Button B1~B2 Function Button Switch.2P .180D.6.8x3.5x4.3mm.12VDC.50mA.100 mohm.SMD.TRONTEK.TS-A01NH-X-S138 (TF)Push Button Boot select Switch.2P .180D.6.8x3.5x4.3mm.12VDC.50mA.100 mohm.SMD.TRONTEK.TS-A01NH-X-S138 Connector Pin Assignments References and diagrams for connector pin assignments are listed below. 2.4.1 MCU Reset Button (SW1) Signal Description... -
Page 22: Micro Usb (Cn1)
2.4.2 Micro USB (CN1) Signal Description Signal Description USB_PWR USB_D- USB_D+ 2.4.3 TCXO_OUT Select (Option for SIGFOX mode) (CN2) Signal Description PH0-OSC_IN PH0-OSC_OUT Chapter 4 – Installation Guide... -
Page 23: Udd_Tcxo Select (Option For Sigfox Mode) (Cn5)
2.4.4 UDD_TCXO Select (Option for SIGFOX mode) (CN5) Signal Description Signal Description PA12 VDD_TCXO +3.3V 2.4.5 ST-Link (CN7) Signal Description Signal Description +3.3V SWDIO SWCLK MCU_nRST PB12 Chapter 4 – Installation Guide... -
Page 24: Power Select (Cn8)
2.4.6 Power Select (CN8) Signal Description VBAT SYS_PWR +5V_USB Set jumper on Pins 1-2 to select power source from batteries. Set jumper on Pins 2-3 to select power source from micro USB (5V). 2.4.7 I2C1 Select (CN9/CN10) CN10 Signal Description Signal Description PA5/ADC5/DAC2 PA4/ADC4/DAC1... -
Page 25: I2C1 (Cn11)
2.4.8 I2C1 (CN11) Signal Description Signal Description +3.3V I2C1 SDA I2C1 SCL Pin 3, Pin 4 function selected by CN9, CN10 2.4.9 UART2 (CN12) Signal Description Signal Description +3.3V USART2_TX USART2_RX Chapter 4 – Installation Guide... -
Page 26: Uart1 (Cn13)
2.4.10 UART1 (CN13) Signal Description Signal Description VCC_UART1 USART1_TXD USART1_RXD CN13 can be set to UART, RS485, or RS232 mode. Configuration is set by JP1~JP4. VCC_UART1 power can be set by CN14 2.4.11 UART1 Power Select (CN14) Signal Description +3.3V VCC_UART1 Set Jumper on Pin1-2 for VCC_UART1 output +3.3V. -
Page 27: Function Button (B1/B2)
2.4.12 Function Button (B1/B2) Signal Description Signal Description PB13 PB14 2.4.13 Boot Select (B3) Signal Description BOOT0 Boot from Flash Memory when button is pressed. Chapter 4 – Installation Guide... -
Page 28: Chapter 3 -Setup And Configuration
Chapter 3 Chapter 3 –Setup and Configuration... -
Page 29: Basic Setup Guide
Basic Setup Guide For basic setup of the AIOT-ILND01 LoRa Node, perform the following steps: Connect the LoRa antenna to the Node Board. Insert two 14500 lithium-ion batteries into battery holder. The Node will boot up automatically. Follow section 3.2 Changing/Reading APPKEY to set APPKEY. Connect to LoRa Gateway. -
Page 30: Changing/Reading Appkey
Changing/Reading APPKEY This section details the steps needed to change APPKEY/APPDEUI and how to read APPKEY/APPDEUI/DEVEUI. Before you start, make sure you have a classic serial software installed on your computer. We recommend using Docklight V2.2 or a similar program. Parameters are: Baudrate: 9600 Parity: None Data bits: 8... -
Page 31: Appkey
3.1.1 APPKEY To Write an APPKEY, you must send the new APPKEY followed by an end frame (0x46 0x0D 0x0B). If completed, the software will reply by 0x46 0x0D 0x0B. To read an APPKEY, send 0x64 0xD0 0xB0. The software will reply by the current APPKEY.