Advertisement
Quick Links
Advertisement
Related Manuals for XpressFill XF4500C
Summary of Contents for XpressFill XF4500C
- Page 1 XpressFill XF4500C Counter Pressure Can Filler Operating Instructions...
-
Page 3: Important Safety Instructions
fi ller covered in this manual unless you are certain the electrical supply has been correctly installed and the bottle fi ller has been properly grounded. 265 Prado Road, Suite 1 • San Luis Obispo, CA 93401 • Tel: (805) 541-0100 • sales@xpressfill.com... -
Page 4: Safety Warnings
XPRESSFILL Systems LLC Safety Warnings... - Page 5 fi rst consulting XpressFill Systems LLC. 265 Prado Road, Suite 1 • San Luis Obispo, CA 93401 • Tel: (805) 541-0100 • sales@xpressfill.com...
- Page 6 Bottle release Pressure release knob 6. Fill and purge spout Level sensor Pressure release tube Can neck filling stopper Pneumatic ram Can rest foot 265 Prado Road, Suite 1 • San Luis Obispo, CA 93401 • Tel: (805) 541-0100 • sales@xpressfill.com...
- Page 7 fi ll sequence is started. Do not put your hands between the can and the foot to prevent injury. 265 Prado Road, Suite 1 • San Luis Obispo, CA 93401 • Tel: (805) 541-0100 • sales@xpressfill.com...
- Page 8 265 Prado Road, Suite 1 • San Luis Obispo, CA 93401 • Tel: (805) 541-0100 • sales@xpressfill.com...
-
Page 9: Operating Procedures
Bottle position (the green fill light will go off). Once you are sure the filler is powering up properly, turn off the power switch on the right side. 265 Prado Road, Suite 1 • San Luis Obispo, CA 93401 • Tel: (805) 541-0100 • sales@xpressfill.com... - Page 10 You have now filled your first cans plugged in correctly, you can open the valves using the XF4500C Filling System. on your tanks and turn on the air compressor. 265 Prado Road, Suite 1 • San Luis Obispo, CA 93401 • Tel: (805) 541-0100 • sales@xpressfill.com...
- Page 11 The inlet pressures can also be adjusted in conjunction with can pressures to change the filling rate and foaming characteristics. 265 Prado Road, Suite 1 • San Luis Obispo, CA 93401 • Tel: (805) 541-0100 • sales@xpressfill.com...
-
Page 12: Troubleshooting
XPRESSFILL Systems LLC Trouble Shooting If at any time you have issues with the setup or adjustment of your XF4500C can fi lling machine, or any other questions about fi lling your product, please contact us at the number listed at the front of this manual. - Page 13 After sanitizing, fl ush your fi ller with 2 gallons of warm water. Before storing your XpressFill fi ller, make sure you get all water out of the fl ow path. Allow to run until pressurized keg with cleaning solution is empty and runs dry, blowing the remaining water out of the fi...
- Page 14 10. Rinse / Sanitize the filler following steps 1 - 9 according to the cleaning solution manufacturer’s instructions. 11. This completes part I of the two part process for cleaning your filler. 265 Prado Road, Suite 1 • San Luis Obispo, CA 93401 • Tel: (805) 541-0100 • sales@xpressfill.com...
- Page 15 8. Turn off the air/gas supply and remove all the INLET hoses. 9. Turn off the filler. 265 Prado Road, Suite 1 • San Luis Obispo, CA 93401 • Tel: (805) 541-0100 • sales@xpressfill.com...
- Page 16 2. Removal requires using the included tool to firmly push the collet and remove the tube. Push the collet in to remove tubing 265 Prado Road, Suite 1 • San Luis Obispo, CA 93401 • Tel: (805) 541-0100 • sales@xpressfill.com...
- Page 17 XPRESSFILL Systems LLC | I Need A Spare Fuse ere is a spare fuse in the power entry connector (where the power cord plugs in). Unplug the machine and set screwdriver on the notch (do not remove screws) and pop the spare fuse holder...
Need help?
Do you have a question about the XF4500C and is the answer not in the manual?
Questions and answers