Table of Contents
Advertisement
Clock/Timer
M I C R O S Y S T E M
M C
M
1 0 8
iR
AM
AUX-IN
Setting the clock
1
In Standby mode, press PROG/CLOCK
button.
The clock digits for the hours flash.
2
Press ¡1 / 2™ to set the hours.
3
Press PROG/CLOCK again.
The clock digits for the minutes flash.
4
Press ¡1 / 2™ to set the minutes.
5
Press PROG/CLOCK to confirm the time.
Note:
– If the clock has not been set, -- --:-- -- will be
displayed.
Setting the timer
The system can be used as an alarm clock. CD
or TUNER can be set to switch on at a preset
time. The clock time needs to be set first
before the timer can be used.
If no button is pressed within 90 seconds during
timer setup, the system will exit timer setting
mode automatically.
1
In any mode, press TIMER on the remote
control for more than 2 seconds.
2
Press ¡1 / 2™ (or CD / TUNER on the
remote control) to select sound source.
3
Press TIMER to confirm your desired source.
The clock digits for the hours flash.
15
4
Press ¡1 / 2™ to set the hours.
5
Press TIMER again.
The clock digits for the minutes flash.
6
Press ¡1 / 2™ to set the minutes.
7
Press TIMER to confirm the time.
The timer is now set and actiated.
Notes:
- If source CD is selected and no disc is in the CD
tray or the disc has an error, TUNER will be
selected automatically.
- At the set time of wake up, the set will turn on at
volume level 12.
To activate and deactivate timer
In standby or during playback, press
TIMER once.
Display shows
if activated, and
disappears if deactivated.
Activating and deactivating
SLEEP
The sleep timer enables the system to switch
off by itself after a set period of time. The clock
time needs to be set first before the sleep timer
can be used.
Press SLEEP on the remote control repeatly
to select desired time before
system shuts off.
Display shows
and
SLEEP
TIMER
SLEEP
series of time options for
selection:
,
,
,
, ,
...
To deactivate, press SLEEP on the remote
control once or more until "
" is shown, or
press STANDBY ON on the system or
remote control.
Troubleshooting
WARNING
Under no circumstances should you try to repair the system yourself, as this will invalidate the
warranty. Do not open the system as there is a risk of electric shock.
If a fault occurs, first check the points listed below before taking the system for repair. If you
are unable to remedy a problem by following these hints, consult your dealer or service centre.
Problem
CD OPERATION
"NO cd" is displayed.
RADIO RECEPTION
Radio reception is poor.
GENERAL
The system does not react when buttons
are pressed.
Sound cannot be heard or is of poor
quality.
The left and right sound outputs are
reversed.
The remote control does not function
properly.
The timer is not working.
The Clock/Timer setting is erased.
Solution
– Insert a disc.
– Check if the disc is inserted upside down.
– Wait until the moisture condensation at the lens
has cleared.
– Replace or clean the disc, see "Maintenance".
– Use a finalised CD-RW or CD-R, or a correct
MP3-CD format disc.
– If the signal is too weak, adjust the antenna or
connect an external antenna for better reception.
– Increase the distance between the Micro HiFi
System and your TV or VCR.
– Remove and reconnect the AC power plug and
switch on the system again.
– Adjust the volume.
– Disconnect the headphones.
– Check that the speakers are connected correctly.
– Check if the stripped speaker wire is clamped.
– Make sure the MP3-CD was recorded within
32-256 kbps bit rate with sampling frequencies
at 48 kHz, 44.1 kHz or 32 kHz.
– Check the speaker connections and location.
– Select the source (CD or TUNER, for example)
before pressing the function button (É,í,ë).
– Reduce the distance between the remote control
and the system.
– Insert the batteries with their polarities
(+/– signs) aligned as indicated.
– Replace the batteries.
– Point the remote control directly toward
IR sensor on the front of the system.
– Set the clock correctly.
– Press TIMER to switch on the timer.
– Power has been interrupted or the power cord
has been disconnected. Reset the clock/timer.
16
Advertisement
Table of Contents
