Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DFI Qseven Q7X-151 R.D1
Summary of Contents for DFI Qseven Q7X-151 R.D1
- Page 1 Q7X-151 (R.D1) Qseven Carrier Board User’s Manual A54900939...
-
Page 2: Copyright
Q7X-151 (R.D1) www.dfi.com Copyright FCC and DOC Statement on Class B This publication contains information that is protected by copyright. No part of it may be re- This equipment has been tested and found to comply with the limits for a Class B digital produced in any form or by any means or used to make any transformation/adaptation without device, pursuant to Part 15 of the FCC rules. -
Page 3: Table Of Contents
Q7X-151 (R.D1) www.dfi.com Table of Contents Front Panel .................18 Copyright .........................2 Cooling Fan Connectors ..............19 Trademarks CAN-Bus Connector ..............19 ......................2 LVDS LCD Panel Connector ............20 FCC and DOC Statement on Class B ..............2 SATA (Serial ATA) Connector ............21 SATA (Serial ATA) Power Connector ..........21 About this Manual ....................4... -
Page 4: About This Manual
Q7X-151 (R.D1) www.dfi.com About this Manual Static Electricity Precautions This manual can be downloaded from the website, or acquired as an electronic file included in It is quite easy to inadvertently damage your PC, system board, components or devices even the optional CD/DVD. -
Page 5: About The Package
Q7X-151 (R.D1) www.dfi.com About the Package The package contains the following items. If any of these items are missing or damaged, please contact your dealer or sales representative for assistance. • One Q7X-151 (R.D1) board • One Serial ATA cable Optional Items •... -
Page 6: Chapter 1 - Introduction
Chapter 1 - Introduction Q7X-151 (R.D1) www.dfi.com Chapter 1 - Introduction ► Specifications Graphics • Display ports Expansion Slots • 2 PCIe x1 slot - 1 dual channel LVDS • 2 Mini PCIe slot - 1 eDP port • 1 SDIO socket... -
Page 7: Chapter 2 - Hardware Installation
Chapter 2 - Hardware Installation Q7X-151 (R.D1) www.dfi.com Chapter 2 - Hardware Installation ► Board Layout Battery Important: Electrostatic discharge (ESD) can damage your board, pro- COM 1 cessor, disk drives, add-in boards, and other components. DC-in System Fan 1 Perform installation procedures at an ESD workstation only. -
Page 8: Mechanical Diagram
Chapter 2 - Hardware Installation Q7X-151 (R.D1) www.dfi.com ► Mechanical Diagram ► Jumper Settings Clear CMOS 157.48 151.76 124.83 114.95 94.89 73.83 If any anomaly of the followings is encountered — 53.45 a) CMOS data is corrupted; 39.79 b) you forgot the supervisor or user password;... -
Page 9: Usb Power Select
Chapter 2 - Hardware Installation Q7X-151 (R.D1) www.dfi.com ► Jumper Settings ► Jumper Settings USB Power Select USB Signal Select JP23 USB 4/5 (USB 2.0) USB 6/7 JP10 (USB 2.0) JP1 (for rear I/O USB 0/1), JP2 (for rear I/O USB 2/3), JP23 (for rear I/O USB 4/5), and JP10 Each of the two USB 3.0 rear channels (A and B) can act as a single USB 3.0 port without ad-... -
Page 10: Panel Power Select
Chapter 2 - Hardware Installation Q7X-151 (R.D1) www.dfi.com ► Jumper Settings ► Jumper Settings Panel Power Select Backlight Power Select JP21 JP16 JP21 is for selecting the power voltage supplied to the LCD panel. JP16 is for selecting the backlight power voltage — +5V or +3.3V. -
Page 11: Lcd/Inverter Power Select
Chapter 2 - Hardware Installation Q7X-151 (R.D1) www.dfi.com ► Jumper Settings ► Jumper Settings LCD/Inverter Power Select Dimming Mode Select LCD/Inverter JP11 Power JP17 JP17 is for selecting the power voltage of the LCD/Inverter power. JP11 is for selecting the mode for lightness control of the LVDS panel — PWM Mode or Voltage Mode. -
Page 12: Bios Boot Select
Chapter 2 - Hardware Installation Q7X-151 (R.D1) www.dfi.com ► Jumper Settings ► Jumper Settings BIOS Boot Select ATX/AT Power Select JP12 J9 is for selecting the BIOS boot source — carrier board or Qseven module. JP12 is for selecting the ATX/AT power — 5V, 5V_standby, or N.C. -
Page 13: Lpc/Gpio Switch
Chapter 2 - Hardware Installation Q7X-151 (R.D1) www.dfi.com ► Jumper Settings ► Jumper Settings LPC/GPIO Switch High/low Switch for MXM Pin 27 JP24 JP25 JP24 is for switching between LPC or GPIO (DIO) signals. JP25 is for switching between high and low voltage of the battery low/General Purpose Input (GPI) pin (pin 27) of the MXM connector. -
Page 14: Panel I/O Ports
Chapter 2 - Hardware Installation Q7X-151 (R.D1) www.dfi.com ► Panel I/O Ports ► Panel I/O Ports 12V DC-in Rear panel I/O ports ▼ LAN Line-in ▲ DC-in ▼ USB 2.0 Note ▼ DC-in ▼ USB 2.0 ▼ DP Line-out Mic-in ▲... -
Page 15: Rj45 Lan Port
Chapter 2 - Hardware Installation Q7X-151 (R.D1) www.dfi.com ► Panel I/O Ports ► Panel I/O Ports RJ45 LAN Port DisplayPort ▼ LAN ▲ DisplayPort ▲ DisplayPort The onboard RJ45 LAN port allows the system board to connect to a local area network by DisplayPort is a digital display interface used to connect a display device such as a computer means of a network hub. -
Page 16: Usb Ports
Chapter 2 - Hardware Installation Q7X-151 (R.D1) www.dfi.com ► Panel I/O Ports USB Ports USB 2.0 / USB 3.0 signal switch According to the maximum number of USB 2.0 and USB 3.0 ports supported by different Qseven modules, this carrier board is designed with two numbers of USB ports configurable as listed below. -
Page 17: Audio
Chapter 2 - Hardware Installation Q7X-151 (R.D1) www.dfi.com ► Panel I/O Ports Audio Line-in Line-out Mic-in Rear Audio The system board is equipped with 3 rear audio jacks (Line-in, Line-out, and Mic-in) as intro- duced below. • Line-in Jack (Light Blue) This jack is used to connect any audio devices such as Hi-fi set, CD player, tape player, AM/FM radio tuner, synthesizer, etc. -
Page 18: Internal I/O Connectors
Chapter 2 - Hardware Installation Q7X-151 (R.D1) www.dfi.com ► Internal I/O Connectors Front Panel SMBus Connector ▼ Front Panel Connector PWR-LED HD-LED ▼ SMBus Connector RESET ATX-SW 11 12 ▼ Front Panel Pin Assignment Pin Assignment Pin Assignment N.C. LED Power... -
Page 19: Cooling Fan Connectors
Chapter 2 - Hardware Installation Q7X-151 (R.D1) www.dfi.com ► Internal I/O Connectors ► Internal I/O Connectors Cooling Fan Connector CAN-Bus Connector ▼ System Fan 1 ▼ CAN-Bus This 3-pin fan connector is for connection to a cooling fan. The cooling fan will provide ad- The CAN controller performs communication in accordance with the BOSCH CAN Protocol Ver- equate airflow throughout the chassis to prevent overheating the system board components. -
Page 20: Lvds Lcd Panel Connector
— Panel Power Select, Backlight Power Select, LCD/Inverter Power Select, and Dim- ming Mode Select. LVDS_DDC_CLK N.C. LVDS_DDC_DATA +3.3V Panel Power Panel Power Note: Panel Power Panel Power DFI board’s LVDS connector: Hirose DF13-40DP-1.25V(91)/40P/1.25mm; cable side connector: Hirose DF13-40DS-1.25C. -
Page 21: Sata (Serial Ata) Connector
Chapter 2 - Hardware Installation Q7X-151 (R.D1) www.dfi.com ► Internal I/O Connectors ► Internal I/O Connectors SATA (Serial ATA) Connectors SATA (Serial ATA) Power Connectors SATA 0 (SATA 3.0) SATA Power 0 SATA 1 (SATA 3.0) SATA Power 1 Ground... -
Page 22: Lpc Debug Connector
Chapter 2 - Hardware Installation Q7X-151 (R.D1) www.dfi.com ► Internal I/O Connectors ► Internal I/O Connectors LPC Debug connector C Connector ▲ LPC Connector ▼ I2C Pin Assignment C_DATA C_Clock +3.3V The LPC connector is used for the debug function and its pin functions are listed below. -
Page 23: Expansion Slots
Chapter 2 - Hardware Installation Q7X-151 (R.D1) www.dfi.com ► Internal I/O Connectors Expansion Slots PCI Express x1 Slot Install PCI Express cards such as network cards or other cards that comply to the PCI Express specifications into the PCI Express x1 slot. - Page 24 Chapter 2 - Hardware Installation Q7X-151 (R.D1) www.dfi.com ► Internal I/O Connectors ► Expansion Slots Installing the Mini PCIe card Before installing the Mini PCIe module into the Mini PCIe socket, please make sure that the following safety cautions are well-attended.
-
Page 25: Switches
Chapter 2 - Hardware Installation Q7X-151 (R.D1) www.dfi.com ► Internal I/O Connectors ► Internal I/O Connectors Switches LEDs GPO LED Thermal Trip LED ▲ Lid ▲ Sleep ▲ Power ▲ Reset Thermal Trip LED • Lid — turn the LVDS panel on or off This LED will light to indicate that the processor is on an overheating status. -
Page 26: Battery
Chapter 2 - Hardware Installation Q7X-151 (R.D1) www.dfi.com ► Internal I/O Connectors ► Internal I/O Connectors Battery MXM Connector +3.3V ▲ Battery MXM Socket The MXM connector is used to interface the carrier board with a Qseven R2.1 compatible mod- ule. - Page 27 Chapter 2 - Hardware Installation Q7X-151 (R.D1) www.dfi.com ► Internal I/O Connectors ► MXM Connector Pin Q7 R2.1 Signal Pin Q7 R2.1 Signal Pin Q7 R2.1 Signal Pin Q7 R2.1 Signal Pin Q7 R2.1 Signal Pin Q7 R2.1 Signal 95 USB_P1+...
-
Page 28: Chapter 3 - Supported Software
Chapter 3 - Supported Software Q7X-151 (R.D1) www.dfi.com Chapter 3 - Supported Software ► Realtek Audio Drivers Install drivers, utilities and software applications that are required to facilitate and enhance the To install the driver, click “Realtek Audio Drivers” on the main menu. -
Page 29: Adobe Acrobat Reader
Chapter 3 - Supported Software Q7X-151 (R.D1) www.dfi.com ► Adobe Acrobat Reader 9.3 To install the reader, click “Adobe Acrobat Reader 9.3” on the main menu. 1. Click Next to install or click Change Destination Folder to select another folder.