Page 2
& care manual refrigerator models read this instruction manual before installing your new refrigerator RMI1851XSAB0 RMI1851XSAX0 0006 Importer’s name and address as below. A.M.A. Al Swailem Est. OLAYA Street P.O. Box 544 Riyadh, 11421 Kingdom of Saudi Arabia PM01...
contents 1. SAFETY WARNINGS ................4 2. INSTALLATION ..................5 2.1 Location .................... 5 2.2 Door Handle Install Illumination ............ 5 2.3 Door Space Requirements ............... 6 2.4 Levelling the Unit ................6 2.5 Cleaning Before Use ................ 6 2.6 Before Using Your Unit ..............7 2.7 Interior Accessories ................
1. safety warnings WARNING: • Keep ventilation openings, in the appliance en- closure or in the built-in structure, clear of obstructions. WARNING: • Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
TO AVOID THE RISK OF AN ELECTRICAL SHOCK DO NOT ATTEMPT TO REPAIR THIS APPLIANCE BY YOURSELF. 2. installation 2.1 location When selecting a position for your unit you should make sure the floor is flat and firm, and the room is well ventilated. Avoid locating your unit near a heat source, e.g.
1. Take out the two crisscross screws, and install them into the door holes; turn the screws till to the bottom. 2. Aim at screws to install the handle 3. The screws in the hole at the side of the handle and turn the screws till them very tight.
2.6 before using your unit The refrigerator adopts 230V/60Hz AC power, voltage fluctuations over the range of 196 ~ 264V will cause malfunction or even dam- age, so a 750 W automatic voltage regulator must be installed in concert with the AC power. Do not damage the power cord under any condition so as to ensure safety use, do not use when the power cord is damaged or the plug is worn.
3. product overview Door Shelf Control Dial Door Shelf Temperature control panel Oil Box Adjustable Glass Shelves Salad Bin Cover Salad Bin Door Shelf Levelling Feet *All illustrations in this instruction manual are for indication only; please refer to your in- dividual unit for details.
4.1 Keypad A. SET position set key 4.2 Display screen 1. Shift 1 2. Shift 2 3. Shift 3 4. Shift 4 5. Shift 5 6. Standby indicator 4.3 display • Once initially powered on, the display screen (including the light pad) is on full display for 3s, and then operates as the displayed middle shift.
4.6 fault indication Display Malfunction LED1 and LED2 are on Refrigerator temperature sensor circuit. LED1 and LED3 are on Freezer defrost sensor. LED1 and LED4 are on Ambient temperature sensor. 4.7 temperature control operation 1. Initial setting of fresh compartment control panel is shift 3, for freezer compartment air shutter, the initial setting is Mid position.
5. cleaning 5.1 defrosting Auto-defrost for Frost-free Refrigerator. 5.2 cleaning the interior and exterior of the unit 1. Remove all the shelves and the salad bin. To remove the salad bin first remove the lower door shelf. 2. Wipe the inside of the unit with a weak solution of bicarbonate soda and then rinse with warm water using a wrung-out sponge or cloth.
6.3 servicing The unit should be serviced by an authorized engineer and only genuine spare parts should be used. Under no circumstances should you attempt to repair the unit yourself. Repairs carried out by inex- perienced persons may cause injury or serious malfunction. Contact a qualified technician.
Problem Possible Solution The refrigerator • The freezer door is stuck by food packages. door can not be • Too much food. properly closed. • Tilted refrigerator. Loud noises • Make sure the refrigerator is levelled. • Make sure the refrigerator parts are properly placed.
• Let hot foods cool down to room temperature before placing them into the appliance. Overloading the appliance forces the compressor to run longer. Foods that freeze too slowly may lose quality, or spoil. • Be sure to wrap foods properly, and wipe containers dry before placing them in the appliance.
10. reversing the doors swing Disengage the top hinge, hinge stopple, top hinge. 1. Prepare a cross screwdriver 2. Disengage the top hinge, and a socket head wrench. hinge stopple, top hinge sub- assembly and fixed hinge screws for later use. Freezer compart- ment door...
Page 17
Fresh food compartment door 5. Disengage the fresh food compartment door. Hinge screw bolt. Bottom hinge 6. Disengage the bottom hinge from the left side of the chamber with the cross screwdriver, install it on the left side of the cham- ber, and screw off the hinge screw bolt to install into the left stopple of the hinge.
Page 18
Bushing Door limit stop 7. Disengage the bushing and limit stop from the right side of the fresh food compartment door respectively, and install them on the left side of the door (use two screws to fasten the door limit stop).
Page 19
Left top hinge Top hinge bushing Freezer compart- ment door 9. Take off the top and bottom 10. Align and install the center of bushing from the freezer com- left top hinge onto the axle partment door, and install center on the left side of the them into the axle holes door, and fasten the left top aligned to the axle center on...
Page 20
Socket head wrench Handle fastening screw bolts 13. Disengage 2 handles with the 14. Use the cross screwdriver to socket head wrench. move the handle fastening screw bolts from the left side to the right side by way of piercing. Handle stopple Handle cap...
technical data Rated net volume (L) Rated shelf area (cm2) 10887 Electric power consumption 1.107 in kw·h per 24 hour run (kW·h) Percentage running time (%) Ice quantity produced per 24 hour run (g) Current (A) Defrosting power (W) Voltage (V) Frequency (Hz) Electric Diagram...
Need help?
Do you have a question about the RMI1851XSAB0 and is the answer not in the manual?
Questions and answers