Page 6
UA1Y UA1Z Svenska Polski Norsk Русский English English Deutsch Čeština Français Slovenčina Italiano Türkçe Español Português Nederlands Română Suomi Magyar Dansk Українська...
Page 15
SIRe Advanced Vattenreglering - ventilsystem* RSK-nr Beskrivning Anslutning VLP15LF 673 09 47 Tryckoberoende och modulerande DN15 VLP15NF 673 09 48 Tryckoberoende och modulerande DN15 VLP20 673 09 49 Tryckoberoende och modulerande DN20 VLP25 673 09 50 Tryckoberoende och modulerande DN25 VLP32 670 45 34 Tryckoberoende och modulerande...
Page 16
SIRe Advanced Control del agua - sistema de válvulas* Tipo Descripción Conexión VLP15LF Juego de válvulas independientes de la presión y moduladoras DN15 VLP15NF Juego de válvulas independientes de la presión y moduladoras DN15 VLP20 Juego de válvulas independientes de la presión y moduladoras DN20 VLP25 Juego de válvulas independientes de la presión y moduladoras...
Page 17
SIRe Advanced Regulacja przepływu wody – zestaw zaworów* Type Opis Złącze VLP15LF DN15 Niezależny od ciśnienia VLP15NF DN15 Niezależny od ciśnienia VLP20 DN20 Niezależny od ciśnienia VLP25 DN25 Niezależny od ciśnienia VLP32 DN32 Niezależny od ciśnienia VMT15 DN15 Zawór 3-drogowy i siłownik z modulacją DN20 VMT20 Zawór 3-drogowy i siłownik z modulacją...
Page 18
SIRe Advanced Quick guide/Start up Operation without control unit 1. Check that all constituent parts are present (see section Constituent parts). 2. Mount and connect all units and components and where applicable accessories (e.g. actuator), see wiring diagram. When several units are connected set a unique ID for each unit (1-9) which To run the unit is set in the ID selector of the SIReB1/B2/...
Page 19
SIRe Advanced Control unit SIReUA1 Overview Air curtains SIRe AA °C °C DOOR Fan heaters Back Forward/ Confirm SIRe FA Auto °C °C Manual mode Alarm Red led Run signal Green led 19 .0 -5.0 °C °C Fan speed step Heating step Week program Week program...
Support menu difference open door, (calibrating sensors), The support menu is password protected and activate return water temperature sensor is used for support in contact with Frico or (only valid for water supplied units and authorised installer. SIReWTA is required)
Page 21
SIRe Advanced Table - Alarm Error code Action Cause Check that nothing is obstructing the unit's air intake and exhaust. Thermal contact has deployed. One or more When the overheated motor has cooled the thermal motors are overheated. switch shuts again and the alarm can be reset. At repeated alarms, check the motors, replace damaged Motor alarm motors.
Page 22
- result? If the unit is running act as if it was an E1 program) Communication error. If it is not running, contact Frico technical support. Fault on or missing external room Try to reset the alarm. Check connections and sensor SIReRTX connected to cable.
Page 23
SIReUA1 is control unit, disconnect and reset alarm. units connected to the system. connected Components of different Make sure all units are from the same release, contact Frico Firmware releases are used in the technical support. error system.
Page 24
SIRe Advanced Connecting external control - including BMS functions SIReA1X COM 1 COM 2 ROOM 19 20 21 22 1 2 3 4 5 6 7 8 9 10 1112 15 161718 13 14 + - + - Terminal Functions COM1 RJ12 (6/6) SIRe internal communication COM2...
Page 25
Main offi ce Frico AB Tel: +46 31 336 86 00 Box 102 SE-433 22 Partille mailbox@frico.se Sweden www.frico.se For latest updated information and information about your local contact: www.frico.se...
Need help?
Do you have a question about the SIRe AA Advanced and is the answer not in the manual?
Questions and answers