Advertisement
Quick Links
PB 36 & 564 25K CoolSmart TV
564 25K NOT AVAILABLE IN AUSTRALIA
Compatibility
ProBuilder 36 Clean Face
Packing List
• (1) Convection Manifold (with grill and mounting brackets pre-attached)
• (2) 5" Diameter Aluminum Flex Ducts
• (2) Starter Collars
• (12) Self-Drilling Tek Screws
• (2) Convection Air Deflectors (Used for the PB 36 ONLY – see below)
Convection Air Deflectors- ProBuilder 36 CF ONLY
The 2 deflectors must be installed prior to attaching the CoolSmart kit. After removing the cover plates, install the
deflectors as shown below.
Deflectors are installed here.
Grill and Manifold Dimensions
The grill may be installed over the facing to
provide an aesthetic opening for the
convection outlet. (2) 8-32 x 1-1/2" screws
attach the trim to the upper manifold. This
allows variable thickness of finish material.
Dimensions
a
35-7/8" (912mm)
Page 1 of 12
b
2-7/8" (74mm)
1-1/4" (32mm)
17602034- 7/11/19
(sku# 98900778)
564 25K (Standard or CleanFace)
c
d
34-7/8" (886mm)
Note how the
deflectors points
downward to the
rear.
e
1-3/4" (45mm)
© Travis Industries, Inc.
Advertisement
Related Manuals for Travis Industries CoolSmart PB 36
Summary of Contents for Travis Industries CoolSmart PB 36
-
Page 1: Packing List
(2) 8-32 x 1-1/2” screws attach the trim to the upper manifold. This allows variable thickness of finish material. Dimensions 35-7/8” (912mm) 2-7/8” (74mm) 1-1/4” (32mm) 34-7/8” (886mm) 1-3/4” (45mm) Page 1 of 12 17602034- 7/11/19 © Travis Industries, Inc. - Page 2 Optional Recessed Pocket Min. 1/4" (7mm) Min. 73-3/4" (1690mm) Combustible Facing Min. 45-1/2" Allowed to the top of (1156mm) the zero-clearance box Min. 35" ProBuilder Non-Combustible (889mm) Facing Only 36 CF Fireplace Page 2 of 12 17602034- 7/11/19 © Travis Industries, Inc.
- Page 3 CoolSmart TV Kit 38" (966mm) 37" (941mm) 36" (916mm) Combustible Facing 35" (890mm) (Min. 35" 890mm above 34" (864mm) base of fireplace) Min. 35" ProBuilder 36 Non-Combustible 890mm Facing Only CF Fireplace Page 3 of 12 17602034- 7/11/19 © Travis Industries, Inc.
- Page 4 PB36CF 26-1/2" 674mm Braces for Manifold Support Brackets 3-3/4" Bottom of Upper 96mm Manifold Framing Max. 120" 8-1/2" 3048mm 216mm Min. 73-3/4" 1874mm 41" 1042mm PB 36CF37-3/8" 950mm 15-1/4" 388mm Page 4 of 12 17602034- 7/11/19 © Travis Industries, Inc.
- Page 5 Max. 120" (7mm) (3048mm) Min. 70-7/8" (1801mm) Combustible Facing Allowed Non-Combustible Facing Only 564 25K Fireplace (CF or Std) 564 25K CleanFace 564 25K Standard 41-3/8”(1051mm) 41-3/8”(1051mm) 33-1/8” (842mm) 30-1/4”(769mm) Page 5 of 12 17602034- 7/11/19 © Travis Industries, Inc.
- Page 6 Minimum 1” air gap behind TV to wall. The mantel must extend 2” in front of the Combustible TV and 1” to both sides. Mantel 564 25K Min.33-1/4" Fireplace (844mm) (CF or Std) Page 6 of 12 17602034- 7/11/19 © Travis Industries, Inc.
- Page 7 8-1/2" Max. 120" 216mm 3048mm Min. 70-7/8" 1801mm 564 25K Standard 564 25K CleanFace 37-3/4” (959mm) 38-3/4” (985mm) 17-1/2” (445mm) 19-3/8” (493mm) Flush 18-7/8” (480mm) Extended 37-1/4” (947mm) 37-1/4” (947mm) Page 7 of 12 17602034- 7/11/19 © Travis Industries, Inc.
- Page 8 Slide the outlet into the gap and allow it to sit level again. The two mounting tabs will support the manifold. Mounting tabs Page 8 of 12 17602034- 7/11/19 © Travis Industries, Inc.
- Page 9 Remove the knockouts from the top of the fireplace. Use snips or diagonal cutters to snip the tab on the knockouts. Press on the far side away from the tap to pop the edge of the knockout up. Page 9 of 12 17602034- 7/11/19 © Travis Industries, Inc.
- Page 10 You will need to remove a third cover plate on each side. Remove the 2 screws holding the cover plate in place. Reach in and remove the cover plate. You may discard the plates. Page 10 of 12 17602034- 7/11/19 © Travis Industries, Inc.
- Page 11 Seal the joints with silicone caulk or aluminum (U.L. 181A-P) tape. 12 Install the fireplace into the framed chase. See section “Installation” in the manual. Page 11 of 12 17602034- 7/11/19 © Travis Industries, Inc.
- Page 12 See fireplace installation manual for finishing details. NOTE: The manifold opening protrudes 7/16" (12mm) proud of the framing. The wall may be finished to the opening if you do not wish to use the grill trim. Page 12 of 12 17602034- 7/11/19 © Travis Industries, Inc.