CPE5450 /CPE5450 Master/CPE5450 Slave /CPE5450CD/CPE5450AP/CPE5450FIT/CPE80R/CPE5300/1200AP User Manual Ver1.3 Jul 2019 Product pictures S CPE (Slave CPE) M CPE (Master CPE) ...
Page 2
Specifications : 1.Preparation for installation: 1-0 Shake the devices (CPE5450) separately, to check if the device is damaged from shipment, if you can hear some noise from inside of the device, and you suspect it maybe PCBA board loosened, please contact us, we will help check if you need a replacement.
Page 3
1‐1‐3 1‐2 Ensure you know the CPE kit are ready for installation This step is to verify wireless connection between 2 CPE5450, to make sure they can talk each other, It also helps user to be familiar with the product and prevent any defective item caused by delivery etc. Please be kindly noted that you will need to prepare either a router or a computer for this step. Using both a router and a computer to check is preferred. If you don’t have a computer, we suggest you using a cell phone and a router, currently the devices don’t support cell phone (i.c. iPhone ) to access web page to configure directly. You just need to execute either step 1‐2‐1 or step 1‐2‐2. But you could neglect these 2 steps and proceed to step ( 2‐1) if you neither have a Wi‐Fi router /cabled router , nor a computer (PC), or if you think you know CPE well. ...
Page 4
Equipment: CPE5450 1 pair (2PCS) Wi‐Fi router /cabled router 1pcs PC (Notebook) 1 set ...
Page 5
1‐2‐1‐3 Use Ethernet cable to connect POE port of power adapter to WAN port of CPE5450 (2#) 1‐2‐1‐4 Use Ethernet cable to connect LAN port of CPE5450(2#) to PC 1‐2‐1‐5 Set range between CPE5450 1# and CPE5450 2# : 3 meters is recommended, without obstacle between 2 CPEs 1‐2‐1‐6 Turn on all equipment, especially check as below to see if 2 CPE5450 are turning on, wait for 1 minute 5 ...
Page 9
1‐2‐2‐2 Connect CPE5450 2# to power adapter as following: ...
Page 10
1‐2‐2‐4 Turn on all equipment, especially check as below to see if 2 CPE5450 are turning on, wait for 1 minute Light is on Light is not on ...
Page 11
1‐2‐2‐6 Set IPv4 IP address or IPv6 IP address of the PC to “192.168.188.22”(or 192.168.188.11 etc.), A. B‐ C. Left click “Change Network Adapter Setting” D.Set IPv4 IP address or IPv6 IP address of the PC to “192.168.188.22”(or 192.168.188.11 etc.), 11 ...
Page 12
1‐2‐2‐7 Ping “192.168.188.252 ‐t” Following is Win7 OS A. Click “Windows” icon ...
Page 13
Following messages indicates one CPE5450 device(Master) is working well. 1‐2‐2‐8 Ping “192.168.188.253 ‐t” A. Click “Windows” icon ...
Page 14
Equipment: CPE5450 1 pair (2PCS) Camera 1pcs ...
Page 15
2‐1‐2 Use Ethernet cable to connect LAN port of CPE5450 1# to POE port of power adapter 2‐1‐3 Use Ethernet cable to connect LAN port of CPE5450 2# to POE port of power adapter 15 ...
Page 16
2‐1‐4 Use Ethernet cable to connect WAN port of CPE5450 2# to NVR/DVR 2‐1‐5 Turn on all equipment, especially check as below to see if 2 CPE5450 are turning on, wait for 1 minute, then you could see video of camera on monitor Light is on Light is not on ...
Page 17
2‐2‐1 Use Ethernet cable to connect switch to IP cameras 2‐2‐2 Use Ethernet cable to connect switch to CPE5450 1# 2‐2‐3 Use Ethernet cable to connect LAN port of CPE5450 2# to POE port of power adapter 2‐2‐4 Use Ethernet cable to connect WAN port of CPE5450 2# to NVR/DVR 2‐2‐5 Turn on all equipment, wait for 1 minute, then you could see video of camera on monitor 2‐3 With your router, to extend Wi‐Fi signal, CPE5450 kit are used as Wi‐Fi repeater 2‐3‐1 Please kindly refer to step 1‐2‐1 (from 1‐2‐1‐1 to 1‐2‐1‐7) 2‐2‐2 The default password for the device is : 66666666 2‐2‐3 IP address for another CPE, M (Master) CPE5450 is: 192.168.188.252, and IP address for S(Slave) CPE5450 is :192.168.188.253, so you could log into the device via page to change SSID and password of the device. 17 ...
Page 18
Warning: Do not push “Reset” button of CPE4540 , if you keep pushing “Reset” button for longer than 15 seconds, the devices will not maintain connection between 2 CPEs, and then they need to be re‐configured. If you push “Reset”button one time (not longer than 5 seconds), it may cause 3 minutes to 5 minutes transmission issue (not stable) , but it will resume by itself. 3. Use metal hoop with screw fastening to fasten the device 18 ...
Page 19
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.