Table of Contents
Advertisement
H9723AD(EN).qx3
04.6.25
Maintenance
Cleaning the Cabinet
• Use a soft cloth slightly moistened with a mild detergent solution. Do not use a solution containing alcohol, spirits, ammonia or abrasives.
Cleaning Discs
• When a disc becomes dirty, clean it with a cleaning cloth.Wipe the disc from the centre out. Do not wipe in a circular motion.
• Do not use solvents such as benzine, thinner, commercially available cleaners, or antistatic spray intended for analogue records.
Cleaning the disc lens
• After prolonged use, dirt or dust may accumulate at the disc lens.To ensure good playback quality, clean the disc lens with Philips CD
Lens Cleaner or any commercially available cleaner. Follow the instructions supplied with the cleaner.
Specifications
PLAYBACK SYSTEM
DVD Video, Audio CD, DVD+R/RW, DVD-R/RW,
CD-R/RW,VIDEO CD, SVCD
TV STANDARD (PAL/50Hz) (NTSC/60Hz)
Number of lines 625
Playback
Multistandard
VIDEO PERFORMANCE
Video output
RGB output
Video Shift
VIDEO CASSETTE RECORDER
Video heads
Antenna
VHF output
AUDIO FORMAT
Digital
MPEG
Troubleshooting
Problem
No power
No picture
Distorted picture
Completely distorted picture or
black/white picture with DVD
No sound or distorted sound
No audio at digital output
No sound and picture
Picture freezes momentarily during
playback
Disc cannot be played
No return to start-up screen when disc is
removed
The DVD/VCR does not respond to the
remote control
Buttons do not work or DVD/VCR stops
responding
DVD/VCR does not respond to some operating
commands during playback.
The DVD/VCR cannot read CDs/DVDs
The DVD/VCR switches from DVD mode to
VCR mode after 35 minutes
The VCR do not record a TV program
The DVD/VCR do not perform a timer
The motor (cylinder) rotates even when tape
playback is stopped
You cannot insert a tape
You cannot remove a tape
DVD/VCR ejects the tape when you press
RECORD or TIMER SET for a timer recording.
If you are unable to remedy a problem by following these hints, consult your dealer or service centre (HOTLINE).
18
3:28 PM
Page 18
Analogue Stereo Sound
Dolby Surround-compatible downmix from Dolby
Digital multi-channel sound
3D Sound for virtual 5.1 channel sound on 2 speakers
525
(PAL/NTSC)
AUDIO PERFORMANCE
DA Converter 24 bits
DVD
1 Vpp into 75 ohm
0.7 Vpp into 75 ohm
CD
Left/Right
Signal-Noise (1kHz)
Dynamic Range (1kHz)
Distortion and Noise (1kHz) 0.1%
Six heads Hi-Fi
CONNECTIONS
VHF/UHF - 75 ohm
Front panel:
75 ohm unbalanced
Video input
Audio input
Compressed
Rear panel:
Digital
Audio/Video output/input
Solution
– Check if the AC power cord is properly connected.
– Check if the TV is switched on.
– Check the video connection.
– Sometimes a small amount of picture distortion may appear.This is not a malfunction.
– Connect DVD/VCR directly to the TV.
– Make sure the disc is compatible with the DVD/VCR.
– Adjust the volume.
– Check that the speakers are connected correctly.
– Check the digital connections.
– Check if the audio format of the selected audio language matches your receiver
– Check that the RF or AV cables are connected to the correct device (see Connecting to a TV).
– Check the disc for fingerprints/scratches and clean with a soft cloth wiping from centre
– This may happen when you use the disc recorded in the non-seamless manner.
– Ensure the disc label is facing up.
– Check if the disc is defective by trying another disc.
– Reset the unit by switching the DVD/VCR off, then on again.
– Aim the remote control directly at the sensor on the front of the DVD/VCR.
– Reduce the distance to the DVD/VCR.
– Replace the batteries in the remote control.
– Re-insert the batteries with their polarities (+/– signs) as indicated.
– To completely reset the DVD/VCR, unplug the AC cord from the AC outlet for 5-10
– Operations may not be permitted by the disc.
– Use a commonly available cleaning CD/DVD to clean the lens before sending the DVD/VCR
– Playback will stop for more than 35 minutes when no button is pressed.
– Make sure the tape has a record tab.
– Make sure the DVD/VCR is in VCR position.
– Check the TV and the DVD/VCR channel are similar.
– Make sure the recording start and stop times are set correctly.
– Make sure the tape has a record tab.
– Make sure the clock is set.
– The DVD/VCR may not perform or continue a timer recording if the power fails for more
– To enable quick play mechanism, the cylinder will rotate for about five minutes.
– Insert a tape, window side up with the record tab facing you.
– Gently push on the center of the tape when putting into the DVD/VCR.
– Make sure the power plug is completely connected to a power outlet.
– Make sure the tape has a record tab.
Dolby Digital 16, 20, 24 bits
PCM
fs, 44.1, 48, 96 kHz
fs 96 kHz
20 Hz - 44 kHz
fs 48 kHz
20 Hz - 22 kHz
fs 44.1 kHz
20 Hz - 20 kHz
70 dB
90 dB
RCA connector x 1
RCA connector x 2
RCA connector x 6
capabilities.
edge.
This is not a malfunction.
seconds.
Refer to the instructions of the disc.
for repair.
than 1 minute.
This is not a malfunction.
S-Video output
Mini DIN 4-pin Jack
(75 ohm) Analog
audio output (DVD)
RCA connector x 2
(one left channel,
one right channel)
2 Vrms (47 kilo-ohm)
Coaxial digital audio output One pin Jack,
500mVpp (75 ohm)
CABINET
Dimensions (w x h x d)
435 x 94 x 233 mm
Weight
Approximately 3.1 Kg
POWER SUPPLY (UNIVERSAL)
Power inlet
230 ~ 240 V , 50 Hz
Power usage
21 W
Power usage standby
9.2 W
(standby : 5.0 W)
(When CLOCK DISPLAY
set to OFF.)
Specifications subject to change without prior notice
Advertisement
Table of Contents
