Table of Contents
Advertisement
H9924RD_EN_0316 3/17/05 10:11 AM Page 8
Setting Up your DVD/ VCR
Automatic Channel Setup
You can programme the tuner to scan only the channels that
you can receive in your area.
1 Turn on the TV and select the video out channel on your TV.
2 Press VCR, then DISC/VCR MENU.
3 Press K/L to select "TUNER SET UP", then press B.
4 Press K/L to select
"AUTO TUNING", then press B.
• The tuner scans and memorises
all the active channels in your
area. After scanning, the tuner
stops on the lowest memorised
channel.
5 Press P+/P- or numerical key pads
to scan through channels you have
received.
Manual Channel Preset
1 Press VCR, then DISC/VCR MENU.
2 Press K/L to select "TUNER SET UP", then press B.
3 Press K/L to select "MANUAL
TUNING", then press B.
4 Press K/L to select "PROG.", then
press B.
5 Press K/L or numerical key pads
to select your desired programme
number, then press B.
• You can select programme
number 01-99.
• If "ON" appears on the right side of "SKIP", press K/L to
select "SKIP".Then, press B to select "OFF".
6 Press K/L to select "CHANNEL", then press B.
7 Press K/L.The DVD/VCR tuner will begin to search up or
down automatically.When a channel is found, the DVD/VCR
will stop searching and the picture will appear on the TV
Screen.
• You can select desired channel number by using numerical
key pads. Press three digits to select the channel number.
(To select channel 24, first press 0 button then press 2 and 4.)
• If this is the channel you want, press B.
• If you want to remove scrambled signals, press K/L to select
"DECODER".Then, press B to select "ON".
8 Press STATUS/EXIT to exit.
Notes:
– To confirm that a channel has been added, press the
P+/P- buttons.
– You should select the satellite channels to be received by
the satellite receiver directly on the receiver itself.
How do I change "VIDEO MODE"?
If you want to change the video mode, select "VIDEO MODE"
with K/L.
Then, press B to select your desired mode.
Follow TV (Automatic TV channels sorting)
When the automatic channel search function is activated, the
TV channels are saved in a specific order. This may vary from
the order of TV channels on the TV. This function changes the
order of TV channels saved in the DVD/VCR to match that of
the TV. Make sure that the DVD/
VCR and the TV are connected by
a SCART cable.
1 Press VCR, then DISC/VCR MENU.
2 Press K/L to select "TUNER SET
UP", then press B.
3 Press K/L to select "FOLLOW
TV", then press B.
4 "P:01" will appear in the DVD/ VCR display.
I cannot switch my TV to programme number "1"
If you have connected additional devices to socket
AV2(DECODER), please disconnect these devices. Because of
other connected devices, the TV could switch to the programme
number of the scart socket.
8
"NO TV SIGNALS" appears in the TV screen.
The DVD/ VCR is not receiving a video signal from the TV.
Check the plug on the SCART cable.
Check your TV's operating instructions to see which scart socket
is used for video signals.
If this does not help, it's not possible to use this function. Please
read the section Sorting TV channels manually.
5 Select programme number "1" on the TV.
6 Confirm with B on the DVD/VCR remote control.The DVD/
PLEASE WAIT
START
FINISH
7 Wait until the next number, e.g. 'P:02' appears in the display.
8 Select the next programme number on the TV, e.g. "2".
9 Confirm with B.
10 Repeat steps 7 to 9 until you have assigned a programme
11 To end, press STATUS/EXIT.
MANUAL TUNING
PROG.
P55
CHANNEL
055
DECODER
[OFF]
SKIP
[OFF]
VIDEO MODE
[SECAM]
SET=K L OR 0 – 9
The clock resets automatically
END=EXIT
If you save a TV channel that transmits VPS/PDC or the Teletexte on
programme number "P01", date and time will constantly be updated.
As a result, time changes, i.e. daylight savings time, will be set
automatically.
1 Press VCR, then DISC/VCR MENU.
2 Press K/L to select "TUNER SET
3 Press K/L to select "MOVE", then
4 Press K/L to select the saved TV
5 Confirm with B.
6 Move the selected channel with K/L to the programme
7 Confirm with B.
8 To assign other TV channels to a programme number, repeat
9 Confirm the assignment of the TV channel with MOVE menu.
10 To exit the MOVE menu, press STATUS/EXIT.
1 Press VCR, then DISC/VCR MENU.
2 Press K/L to select "INITIAL SET
3 Press K/L to select "LANGUAGE",
4 Select the desired language with
5 To end, press STATUS/EXIT.
SELECT K L CHOOSE B
AUTO TUNING
MANUAL TUNING
FOLLOW TV
MOVE
END=EXIT
1 Press VCR, then DISC/VCR MENU.
2 Press K/L to select "INITIAL SET
3 Press K/L to select "CLOCK",
VCR compares the TV channels on the TV and the DVD/VCR.
If the DVD/VCR finds the same TV channel as on the TV, then
it stores it at "P01".
number to all TV channels.
Sorting TV channels manually
After you have performed the automatic channel search you
may not agree with the sequence in which the individual TV
channels have been allocated to the programme positions
(programme numbers) of the DVD/VCR.You can use this
function to individually sort the TV channels already saved.
UP", then press B.
press B.
channel that you want to change.
number you want to assign.
steps 4 to 7.
Setting the language
You can change the language for the TV screen menu. However,
the DVD/VCR display will only display English text regardless
of this setting.
UP", then press B.
then press B.
K/L.
Setting the clock
If the display shows an incorrect time or " --:-- ", the time and
date must be reset manually.
If a TV channel that transmits VPS/PDC or the Teletexte is
stored under programme number "P01", time/date will
automatically be taken from
VPS/PDC or the Teletexte
information. (Smart Clock)
UP", then press B.
then press B.
MOVE
P01:
02
P06:
90
P02:
03
P07:
99
P03:
05
P08:
121
P04:
10
P09:
124
P05:
74
P10:
130
SELECT K L CHOOSE B
END=EXIT
SELECT K L
ENGLISH
FRANÇAIS
ESPAÑOL
DEUTSCH
ITALIANO
SVENSKA
NEDERLANDS
END=EXIT
TIME --:--
DATE --/--/--
SMART CLOCK [ON]
END=EXIT
Advertisement
Table of Contents
