Advertisement
Quick Links
π
H-7862
HANDS DOWN
HAND DRYER
TOOLS NEEDED
Drill
8mm Drill Bit x 1
Wire Brush x 1
WARNING! For proper electrical connections,
check the local building codes. The dryer must
be installed by a qualified, licensed electrician.
Check that the electrical supply corresponds to that
shown on the rating sticker on the hand dryer. If the
hand dryer is connected to an electrical source other
than what is stated on the rating sticker, permanent
damage or improper, unsafe operation may result.
Make sure electricity is turned off at the main panel
before installing, maintaining or cleaning the hand
dryer. Dryer must be installed in accordance with the
rules and applicable federal, state and local laws,
including fire prevention.
Do not wire the hand dryer into the lighting circuit. It
must be protected by an independent circuit.
PAGE 1 OF 7
1-800-295-5510
uline.com
Mounting Screw x 4
PRE-INSTALLATION WIRING
PARTS
Wall Anchor x 4
Wall Plate x 1
The dryer is intended to be permanently connected to a
power supply and must be properly grounded.
SAFETY
Troubleshooting and inside maintenance must be
performed by a qualified service personnel.
Do not use power wash equipment to clean the dryer.
WARNING! Risk of electric shock. Do not
remove the cover or attempt to repair unless
qualified personnel are servicing the hand
dryer. If the cover is removed or handled
incorrectly, the internal elements of the
hand dryer may cause damage or become
permanently damaged.
Mounting Display x 1
0219 IH-7862
Advertisement
Related Manuals for U-Line H-7862
Summary of Contents for U-Line H-7862
- Page 1 π H-7862 1-800-295-5510 uline.com HANDS DOWN HAND DRYER TOOLS NEEDED Drill 8mm Drill Bit x 1 PARTS Mounting Screw x 4 Wall Anchor x 4 Wire Brush x 1 Wall Plate x 1 Mounting Display x 1 PRE-INSTALLATION WIRING WARNING! For proper electrical connections, The dryer is intended to be permanently connected to a check the local building codes.
-
Page 2: Installation
PRE-INSTALLATION WIRING CONTINUED Do not use the dryer for drying anything other than WARNING! To avoid the risk of fire or electric hands. shock, do not expose the elements and the internal mechanisms of hand dryer to water Do not obstruct air inlets or outlets. or humidity. - Page 3 INSTALLATION CONTINUED 6. Once five holes have been drilled, attach wall 8. Open cover of connector box where cable to bracket to wall by inserting three wall anchors into network will be installed. (See Figure 4) top three holes and one wall anchor in the bottom hole.
- Page 4 INSTALLATION CONTINUED 10. Once cable has been passed through hole, 12. Place hand dryer on wall bracket. (See Figure 8) connect each end to respective terminal, placing each one in the right path. Close box. (See Figure 6) Figure 6 Figure 8 11.
-
Page 5: Maintenance
MAINTENANCE WARNING! Before servicing or cleaning unit, 2. Pull tab in slightly and pull tank down. Empty and clean water tank. (See Figure 11) switch off power at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. WARNING! When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the... -
Page 6: Hepa Filter
MAINTENANCE CONTINUED HEPA FILTER Regularly check the HEPA H13 filter at base of hand dryer and make sure that it is free of dust or other particles. Change filter when necessary or at least once per year. 1. To change filter, pull tab on filter in and down. Replace with authentic ffuuss HEPA H13 filter. -
Page 7: Troubleshooting
SPECIFICATIONS CONTINUED Regulations This unit complies with the following directives/normatives: 1999/5/CE, 2004/108/CE, 2006/95/CE, 2002/96/CE, 2011/65/CE. Others This unit has Bluetooth™ technology. Standard Five years for parts and one year for labor (see conditions). Warranty TROUBLESHOOTING OPERATING ISSUE RECOMMENDATIONS Doesn't turn on. Make sure wiring is properly connected to hand dryer.