Table of Contents
Advertisement
Quick Links
All Restoration Hardware cribs are designed to meet the highest safety
standards and comply with all U.S. and Canadian cribs and cradles regulations.
Made in Vietnam
Distributed in the U.S.A. by:
Restoration Hardware Baby & Child
11640 Harrel St. Suite B
Mira Loma, CA 91752
www.rhbabyandchild.com
Distributed in Canada by:
Restoration Hardware Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia V6E4N7
WARNING:
instructions before assembling this
product. KEEP INSTRUCTIONS
FOR FUTURE USE.
If you are missing parts or have any questions about this product, contact us first. You can also order parts by writing to
the address above. Include the product model number, color, and a brief description of the part. Call 1-800-762-1751.
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Dust often using a clean, soft, dry
cloth. Blot spills immediately and wipe with a clean damp cloth. If the crib is to be stored, store in a cool dry place and
NOTE: When inserting bolts, turn clockwise until tight. Then loosen
completely assembled, return to each bolt and tighten. Use wax or soap on all bolts to facilitate assembly
Read all
CUSTOMER SERVICE
CARE AND CLEANING
carefully package all original hardware to protect from loss.
TOOLS AND INSTALLATION
Tools Necessary: Allen Key (included)
NOTE: It may be easier to assemble product with two people.
Page 1 of 10
Model No. 105024
"BELLINA CONVERSION CRIB"
1
3
-
of a turn. After crib is
2
4
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Restoration Hardware Baby & Child BELLINA CONVERSION CRIB 105024
Summary of Contents for Restoration Hardware Baby & Child BELLINA CONVERSION CRIB 105024
- Page 1 All Restoration Hardware cribs are designed to meet the highest safety standards and comply with all U.S. and Canadian cribs and cradles regulations. Model No. 105024 Made in Vietnam "BELLINA CONVERSION CRIB" Distributed in the U.S.A. by: Restoration Hardware Baby & Child 11640 Harrel St.
- Page 2 IMPORTANT SAFETY INFORMATION FOR CRIBS WARNING: Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional padding under an infant. WARNING: Failure to follow these warnings and the assembly instructions could result in serious injury or death. •...
- Page 3 IMPORTANT SAFETY INFORMATION FOR CRIBS CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27-1/4 INCHES BY 51-5/8 INCHES WITH A THICKNESS NOT EXCEEDING 6 INCHES. WARNING DO NOT use this crib if the enclosed or attached instructions •...
- Page 4 IMPORTANT SAFETY INFORMATION FOR TODDLER & DAY BEDS WARNING : ENTRAPMENT / STRANGULATION HAZARD Infants have died in toddler beds from entrapment and strangulation. Failure to follow these warnings and the assembly instructions could result in serious injury or death. NEVER use bed with children under 15 months.
- Page 5 ITEM IDENTIFICATION For ease of identification, all parts are labeled to correspond to the Step numberin which the part is used. Step #1 Leg assembly to Headboard and End Rail Panel Headboard, Footboard and Stationary Side Rail assembly (Page 6 of 10) Step #2 Mattress Support and Stabilizer Rail assembly.
- Page 6 STEP #1 HEAD BOARD & End Rail Panel ASSEMBLY STEP #1.1 Gently lay the Headboard and End Rail Panel on DETAIL A their backs on a clean and non-abrasive surface. STEP #1.2 Align and insert the threaded rod of the Legs into the hole on the bottom of the Headboard and End Rail Panel and turn clockwise to tighten.
- Page 7 STEP #2 DETAIL C MATTRESS SUPPORT ARM ASSEMBLY STABILIZER RAIL ASSEMBLY MATTRESS HEIGHT ADJUSTMENT LOCK WASHER MATTRESS STEP #2.1 Lay Mattress Support flat with Stabilizer Rail on each side MATTRESS BOLT Note: On each end of the arm of the Mattress Support, there is a hole for the bolt to pass through that corresponds to the holes located in the frame of the Mattress Support.
- Page 8 STEP #3 INSTALLATION OF STABILIZER RAILS INTO THE END RAIL PANELS DETAIL E STEP #3.1 On inside face of both End Rail Panels are pre-installed metal brackets, designed to hold the Stabilizer Rails. Set both ends of the Stabilizer Rails into brackets as illustrated in DETAIL E.
- Page 9 STEP #4 STATIONARY FRONT RAIL ASSEMBLY DETAIL H STEP #4.1: On both ends of the End Rail Panel are holes for the bolt to pass through which correspond to the holes on the posts of both End Rail Panel with pre-installed nuts.
- Page 10 STEP #5 DETAIL J TODDLER RAIL ASSEMBLY STEP #5.1: Remove the Front Rail Panel of the crib by loosening all the bolts installed. STEP #5.2: Gently tilt the Crib and release the bolts underneath the metal brackets holding the Stabilizer Rails. STEP #5.3 Gently remove the Mattress Support and slightly loosen the bolt at the back of the Headboard that enough to set...
Need help?
Do you have a question about the Baby & Child BELLINA CONVERSION CRIB 105024 and is the answer not in the manual?
Questions and answers