Page 2
FCC INFORMATION FEDERAL COMMUNICATIONS COMMISSION INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates, uses, and can radiate radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication.
Page 3
2-IN-1 HEADSET FCC REQUIREMENTS FOR TELEPHONE-LINE EQUIPMENT 1. The Federal Communications Commission (FCC) has established rules which permit this device to be directly connected to the telephone network with standardized jacks. This equipment should not be used on party lines or coin lines. 2.
Page 4
Items (b) and (d) can be found on the unit’s FCC label. The ringer equivalence number (REN) is used to determine how many devices can be connected to your telephone line. In most areas, the sum of the RENs of all devices on any one line should not exceed five (5.0). If too many devices are attached, they may not ring properly.
Page 5
2-IN-1 HEADSET Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. The LOAD NUMBER (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading.
Page 6
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea recomendado por el fabricante. 8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá a lo descrito en las instrucciones de operación. Todo otro servicio deberá ser referido a personal de servicio calificado. 9.
Page 7
2-IN-1 HEADSET 17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilación. 18. Servicio por personal calificado deberá ser provisto cuando: A: El cable de poder o el contacto ha sido dañado; u B: Objectos han caído o líquido ha sido derramado dentro del aparato;...
Page 8
TRADEMARKS USED IN THIS MANUAL TRADEMARKS USED IN THIS MANUAL ® is a registered trademark of Underwriters Laboratories Incorporated. Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners.
If after reviewing this guide you have any questions concerning the 2-in 1 Headset, please call Black Box Technical Support at 724-746-5500. 2.2 2-in-1 Headset Components 1. Noise Canceling Microphone 2. Flexible Microphone Boom 3.
3. Ear Capsule The 2-in-1 Headset comes out of the box with the ear capsule installed ready to be worn on the right ear (see Figure 3-1). It features an Adjustable Lobe Hinge for a custom fit. To change to the left ear, see Section 3.2. Figure 3-1.
2-IN-1 HEADSET Figure 3-3. Changing Ears. 3. Rotate 180° clockwise if you are going from right ear to left ear, counterclockwise if you are going from left ear to right ear. 3.3 Removal 1. Remove the ear cushion. 2. In the right-ear wearing style with the speaker facing you, hold the headset in your left hand between your thumb...
4. Headband The 2-in-1 Headset can also be equipped with a lightweight flexible headband. 4.1 Installation 1. Remove the ear capsule. 2. With the corded side of the receiver facing you, hold the headset in your left hand between your thumb and index finger with the boom pointing to the right.
2-IN-1 HEADSET Figure 4-3. Changing Ears. 4.4 Headband Wearing Position the headset lightly on your head (see Figure 4-4). The 2-in-1 Headset headband is extremely lightweight, ensuring a comfortable fit that lasts all day. The stabilizer cushion rests just above the ear on the side of your head opposite the receiver.
5. Microphone Positioning To take advantage of the noise- canceling qualities of the microphone, position the 2-in-1 Headset with the flat side of the microphone, marked with an F, facing you. The microphone boom should be adjusted so that the microphone is approximately one finger width away from your lower lip (see Figure 5-1).
2-IN-1 HEADSET 6. Clothing Clip The clothing clip should be fastened for comfortable wearing (see Figure 6-1). Figure 6-1. Clothing Clip. It is designed to prevent the weight of the cord from dislodging the headset. Position the clip conveniently on your clothing.
7. Connecting to Your Telephone An amplifier is needed to connect the headset to the telephone or telephone system. The headset is equipped with a Quick Disconnect plug which mates to a Quick Disconnect jack on the amplifier. Follow the instructions supplied with the amplifier to connect the headset and amplifier to your telephone or telephone system...
2-IN-1 HEADSET 8. Maintenance The foam covers on the receiver and microphone can be washed in mild soap and water. Replacement covers are available from Black Box. Call 724-746-5500 for details. Cautionary Notes to Computer Users When using any headset with a computer, care should be taken in dry or low-humidity environments to protect the user from...
• If you are shipping the 2-in- 1 Headset for repair, make sure you include everything that came in the original package. Before you ship, contact Black Box to get a Return Materials Authorization (RMA) number. CHAPTER 9: Troubleshooting...
Page 21
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500) FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018 Web site: www.blackbox.com • E-mail: info@blackbox.com...