Table des matières 1 - Règles d’utilisation et précautions générales ....p. 6 2 - Présentation de la Série Orion ........p. 7 3 - Fonctionnement ............p. 8 3.1- Principe de fonctionnement ............p. 8 3.2- Principe de confi guration des produits........... p. 9 3.3- Fonctionnement du bouton «Marche/Arrêt»...
Page 5
E - OWR01 : Kit antenne externe ......p. 172 F - OWR02 : Kit antenne interne .......p. 173 G - OWE10 : Clip d’accrochage .........p. 174 H - Liste des canaux radio disponibles ....p. 175 Orion - 324501G - 5 -...
Entretenir le matériel, et procéder à des contrôles périodiques, en fonction de l’intensité de l’utilisation. (1) = La programmation d’un autre canal radio peut s’effectuer uniquement au moyen d’un émetteur équipé du bouton «marche/arrêt». Orion - 324501G - 6 -...
(basse tension, compatibilité électromagnétique, spectre radioélectrique). Pour toutes questions liées à l’installation ou à l’utilisation de la Série Orion, nous vous invitons à contacter notre service client (Lundi au vendredi) : Tel : +33.(0)4.76.41.44.00 Fax : +33.(0)4.76.41.44.44 Email : service.client@jay-electronique.fr...
3 - Fonctionnement 3.1- Principe de fonctionnement La Série Orion permet de commander à distance un ou plusieurs récepteurs équipés de relais. La communication entre l’émetteur et le récepteur s’effectue par ondes radio, sur un canal particulier avec un codage personnalisé...
Les cavaliers de codage des récepteurs ORRS et ORRA doivent être utilisés pour faire le strap correspondant à la programmation souhaitée (plusieurs cavaliers sont livrés avec les produits) : cavalier Cavalier Orion - 324501G - 9 -...
Page 10
: La mise en arrêt automatique de l’émetteur (fonction «Mise en veille») La modifi cation du canal radio de travail Emetteurs sans bouton Emetteurs avec bouton «Marche/Arrêt» «Marche/Arrêt» Orion - 324501G - 10 -...
Page 11
- Il s’ouvre si aucun des relais de fonction n’est actif ou si le récepteur est hors tension ou en cas de perturbation radio de plus d’une seconde quand un des boutons de l’émetteur est appuyé. Orion - 324501G - 11 -...
Page 12
Exemple d’utilisation du relais «RM» programmé en mode «Relais commun» sur récepteur ORRS42••• : ORRS 1 2 3 4 5 6 7 8 9 10 11 12 13 Câblage externe commande commande centrale électrovannes hydraulique (*) = Dispositifs antiparasitage Orion - 324501G - 12 -...
4 - Confi guration par défaut à la livraison 4.1- Instructions avant utilisation Les émetteurs et les récepteurs Orion possèdent des pré- réglages à la livraison permettant d’être utilisés immédiatemment. Cependant, il est indispensable de modifi er et de personnaliser ces réglages afi...
Interverrouillage des Aucun interverrouillage programmé par défaut ordres antagonistes (1) = La programmation d’un autre canal radio peut s’effectuer uniquement au moyen d’un émetteur équipé du bouton «Marche/Arrêt». Orion - 324501G - 14 -...
Kit antenne débrochable OWR01 pour l’utilisation d’une antenne ou rallonge d’antenne débrochable. (5) = ne convient pas pour une connexion directe à l’antenne VUB086, utiliser dans ce cas là une rallonge intermédiaire type VUB1••. Orion - 324501G - 16 -...
(230VAC > 9VDC) livré avec 3 accumulateurs AAA livré avec 3 accumulateurs AAA Pour recharger l’émetteur Orion Multifonctions avec des accus, veillez à : 1. Alimenter le support chargeur 2. Si présent, appuyer sur le bouton «Marche/Arrêt» afi n d’éteindre l’émetteur (voyants rouge et vert éteints).
6.3- Récepteurs Orion (ORR) Industriel Industriel Rail DIN (petit modèle) (grand modèle) (ORRD) (ORRS) (ORRA) Matière du boîtier PC-GF Couleur du boitier Gris Jaune Gris Etanchéité IP20 IP65 IP65 Poids maximal 220 g. 350 g. 1200 g. Nombre de sortie relais de commande...
Grandeur physique commutée par le relais Contacteur (relais de fonction et relais «RM) Commutation sous 230VAC (70VA,cosphi=0,75) 2 x 10 CA2DN LC1D09 Commutation sous 110VAC, (70VA,cosphi=0,75) 1 x 10 LC1D18 LC2D09 Commutation sous 48VAC (70VA,cosphi=0,75) 0,5 x 10 Orion - 324501G - 20 -...
Carte alimentée en 62 mA / 250 VAC / T - F1 160 mA / 250 VAC / T - F1 230VAC - Relais de fonction Pas de protection Pas de protection - Relais «RM» Orion - 324501G - 21 -...
R1 et R2. Position du microswitch JP4 Fonction du relais «RM/R3» Relais «RM» Relais «R3» Remarque : Les programmations pour le relais R3 sont sauvegardées en cas de commutation du microswitch sur la position «OFF». Orion - 324501G - 22 -...
Programmation de la durée temporisation fonction «Mise en (facultative) veille» (arrêt automatique de l’émetteur en cas de non utilisation prolongée) Procéder à l’installation sur site en respectant les recommandations Etape 7 d’installation décrites au chapitre Recommandations d’installation et d’utilisation Orion - 324501G - 23 -...
: ORET, OREi et OREL : 256 possibilités OREV : 4096 possibilités (voir chapitre suivant) L’émetteur Orion possède un DIP-switch de 8 curseurs à 2 états («ON» ou «OFF») afi n de programmer le code d’identité. OREL...
Valider le groupe de codes d’identité en appuyant sur le bouton B2 (ou bouton «Marche/Arrêt» si présent). Annuler en appuyant sur le bouton interne S1 Composer un code avec le DIP_switch 8 curseurs Refermer le boîtier de l’émetteur OREV Orion - 324501G - 25 -...
Il est possible que le récepteur s’associe à un émetteur non désiré. Pendant toute la durée de l’association Il est recommandé suspendre toute utilisation d’autres émetteurs ORION. Orion - 324501G - 26 -...
Page 27
«OFF» Si aucun bouton de l’émetteur n’est actionné durant cette procédure de programmation, les paramétrages du récepteur (association boutons/relais, interverrouilage et mode de fonctionnement des relais précédemment programmés) ne seront pas effacés. Orion - 324501G - 27 -...
Récepteur ORRD : placer le microswitch sur la position «ON» ORRS ORRA ORRD V1 V2 V3 V1 V2 V3 Récepteurs ORRS et ORRA : mettre le récepteur sous tension Récepteur ORRD : passer à l’étape suivante Orion - 324501G - 28 -...
Page 29
Si d’autres associations doivent être réalisées, reprendre la procédure au point N°3. Une fois toutes les associations terminées : Récepteurs ORRS et ORRA : mettre hors tension le récepteur et retirer le cavalier Récepteur ORRD : placer le microswitch en position «OFF» Orion - 324501G - 29 -...
2 clignotements = mode sélection multirécepteurs à canal fi xe 3 clignotements = mode sélection multirécepteurs à canal auto. Chaque appui sur le bouton va modifi er le mode de fonctionnement. Valider le mode de fonctionnement en appuyant sur le bouton «Marche/Arrêt». Orion - 324501G - 31 -...
METHODE ET PROCEDURE D’ASSOCIATION : Après avoir choisi un code d’identité (DIP_switch 8 curseurs) et éventuellement un groupe de codes d’identité pour l’émetteur OREV, les associations émetteur / récepteurs se font successivement pour chaque récepteur (voir page suivante). Orion - 324501G - 32 -...
Page 33
Récepteurs ORRS et ORRA : mettre hors tension le récepteur et retirer cavaliers Récepteur ORRD : placer les microswitchs en position «OFF» Répéter l’association pour chaque récepteur à associer. Orion - 324501G - 33 -...
Récepteur(s) Récepteur(s) Récepteur(s) Récepteur(s) Canal n° 16 Canal n° 17 Canal n° 1 Canal n° 2 Canal n° 3 Canal n° 11 Ci 157 Ci 157+1=158 Ci 157+2=159 Ci 157+3=160 Ci 157+4=161 Ci 157+12=169 Orion - 324501G - 34 -...
Page 35
Récepteurs ORRS et ORRA : mettre hors tension le récepteur et retirer cavaliers Récepteur ORRD : placer les microswitchs en position «OFF» Répéter l’association pour chaque récepteur à associer. Orion - 324501G - 35 -...
Mode 2 se ferment. Modifi cation du fonctionnement des relais : Une association émetteur/récepteur doit avoir été réalisée. La procédure de changement du mode de fonctionnement met en oeuvre l’émetteur et le récepteur. Orion - 324501G - 36 -...
Page 37
Une fois la programmation terminée : Récepteurs ORRS et ORRA : mettre hors tension le récepteur et retirer le cavalier Récepteur ORRD : placer le microswitch en position «OFF» Orion - 324501G - 37 -...
La programmation des interverrouillages pour ce récepteur ne peut se faire que sur des relais appartenant au même groupe. Exemple : interverrouillage possible entre le relais R1 et le relais R3 et non possible entre R1 et R6. Orion - 324501G - 39 -...
Le récepteur restera sous tension pendant la procédure afi n de recevoir l’ordre de changement de canal radio Emetteurs industriels : B1 B2 B3 B4 Bouton «Marche/Arrêt» électronique Emetteurs multifonctions : Bouton «Marche/Arrêt» électronique électronique électronique électronique Orion - 324501G - 40 -...
Page 41
(01 à 18), et les deux appareils sauvegardent le changement. La procédure se fi nit lorsque les deux voyants de l’émetteur Va et Vb s’éteignent (environ 10s). Orion - 324501G - 41 -...
6 fois, le canal radio de travail est donc «06» (433.600MHz). Récepteurs ORRS et ORRA : mettre hors tension le récepteur et retirer les cavaliers Récepteur ORRD : placer les microswitchs en position «OFF» Orion - 324501G - 42 -...
Chaque appui sur le bouton B1 va incrémenter la valeur du niveau de puissance radio de 1. Valider le niveau de puissance radio en appuyant sur le bouton B2 (ou bouton «Marche/ Arrêt» si présent). Annuler en appuyant sur le bouton interne S1 Refermer le boîtier de l’émetteur OREV Orion - 324501G - 43 -...
Page 44
Une fois la nouvelle durée sélectionnée, actionner le bouton «marche/arrêt» pour valider le choix. L’émetteur enregistre alors la modifi cation. Orion - 324501G - 44 -...
Tous les paramètres du récepteur (excepté le canal radio de travail) sont effacés Récepteurs ORRS et ORRA : mettre hors tension le récepteur et retirer les cavaliers Récepteur ORRD : placer les microswitchs en position «OFF» Orion - 324501G - 45 -...
Les voyants Va et Vb de l’émetteur clignotent alternativement. L’effacement et la reprogrammation des paramètres «départ usine» de l’émetteur est terminée lorsque les voyants Va et Vb s’éteignent. Refermer le boitier de l’émetteur OREV. Orion - 324501G - 46 -...
Exemples de système de protection à utiliser : Bornier des sorties du récepteur Sortie sur relais en AC Sortie sur relais en DC Entrée automate (Circuit RC) (Diode de roue libre) (résistance de tirage R=Vdc/Imin(10mA)) Orion - 324501G - 47 -...
électrique pour la commande de puissance par exemple). 8.5- Emetteurs «Multifonctions» (OREL) équipés d’accumulateurs avec support chargeur (ORCL•) Lorsque les émetteurs sont équipés d’accumulateurs, veuillez effectuer une charge d’une durée de 3 heures environ avant une première utilisation. Orion - 324501G - 48 -...
Elle ne doit jamais traverser une paroi, même isolante. Il est à noter que la meilleure portée est obtenue en inclinant l’émetteur ainsi qu’indiqué dans le schéma ci-dessous : Emetteur Récepteur Orion - 324501G - 49 -...
Page 50
ORRA et ORRS : antenne VUB084 ou antenne VUB086 Installation en armoire plastique ORRD : antenne VUB084 + coude 90° VUB060 Antenne VUB084 + rallonge 0,5m VUB170 Installation en armoire métallique ou antenne VUB086 + rallonge 0,5m VUB170 Orion - 324501G - 50 -...
Instructions à suivre pour ouvrir les borniers de raccordement : 1. Insérer un tournevis verticalement (lame plate de 1,5 à 3 mm de largeur) dans la fente située au regard du fi l, 2. Insérer le fi l, 3. Retirer le tournevis. Orion - 324501G - 51 -...
à létat du joint d’étanchéité (émetteur multifonctions OREL). - Procéder au nettoyage de l’émetteur en éliminant tout corps étranger y adhérant. N’utiliser que des nettoyants non agressifs à base de solution savonneuse. Orion - 324501G - 52 -...
Page 53
- Procéder au nettoyage du récepteur en éliminant tout corps étranger y adhérant. N’utiliser que des nettoyants non agressifs à base de solution savonneuse. Orion - 324501G - 53 -...
à cet effet se trouvant : - Dans toutes les déchetteries, dans les conteneurs à cet effet, - Dans toutes les mairies - Dans toutes les grandes surfaces - D’une façon générale, chez les artisans et commerçants volontaires. Orion - 324501G - 54 -...
été effectués par le client sans l’ accord écrit de notre Société. La responsabilité de la Société JAY Electronique pendant la période de garantie est limitée à tout vice de matière ou de construction; elle comprend la réparation en ses ateliers ou le remplacement gratuit des pièces reconnues défectueuses après...
Service your equipment, and perform all periodic checks as may be required by the intensity with which your equipment is used. (1) = The programming of another radio channel number can only be done with a transmitter equipped with an «On/Off» button. Orion - 324501G - 60 -...
-Machinery Directive -RTTE : microwave equipment and telecommunication terminals (low voltage, electromagnetic compatibility, radio-electric spectrum). For all questions relative to installation or use of the Orion Series products, contact our customer service department (Monday to Friday) : Tel : +33.(0)4.76.41.44.00 Fax : +33.(0)4.76.41.44.44...
3 - Operating 3.1- Operating principle Orion Series provides remote control of one or several receivers equipped with relays. The transmitter and receiver communicate by radio waves on a specifi c channel with a customized code (identity code). The radio link is momentary; it is only active when the button on the transmitter is pressed.
The encoding jumpers used with the ORRS and ORRA receivers must be used to defi ne the settings corresponding to the desired programming (several jumpers are supplied with the products) : jumper Cavalier jumper Orion - 324501G - 63 -...
The transmitter models equipped with this button have two user- defi nable functions : Transmitter automatic shutdown (“standby function”) Modifi cation of working radio channel Transmitters without Transmitters with «On/Off» button «On/Off» button Orion - 324501G - 64 -...
- The contact opens if none of the function relays is active or if the receiver is switched off or in case of radio jamming (>1s) while a transmitter function button is pressed. Orion - 324501G - 65 -...
Page 66
Example of use of «RM» relay, programmed with mode 2 «Common relay» for receiver ORRS42••• : ORRS 1 2 3 4 5 6 7 8 9 10 11 12 13 External wiring hydro-electric solenoid valve group control control (*) = Interference suppression devices Orion - 324501G - 66 -...
4 - Default confi guration on delivery 4.1- Instructions before use The Orion transmitters and receivers are supplied with certain parameters pre-set in factory to allow immediate use of the equipment. However, it is indispensable to customise these settings to ensure the uniqueness of your installation and to familiarise...
4.3- Orion receivers delivery confi guration Transmitter buttons Receiver on DIN rail ORRD22••• (2+1 or 3 relays) : / receiver relays - Transmitter buttons B1 and B2 assigned to relays R1 and R2 association - «On/R3» relay set for «On» relay»...
OWR01 for use of an antenna or a plug-in antenna extension. (5) = Not suitable for direct connection to antenna VUB086 ; in this case, use an intermediate extension type VUB1••. Orion - 324501G - 70 -...
6 - Technical characteristics 6.1- Orion transmitters (ORE) Standard Industrial Industrial Multifunction (ORET) (OREi) (OREV) (OREL) Housing material Housing color black yellow / black yellow / black yellow Degree of protection IP40 IP65 IP65 IP65 Weight (with batteries or accu.) 65 g.
6.2- Charger supports IMPORTANT : The charger supports can only be used with the Multifunction Orion transmitters (ORELxxxxx) equipped with AAA accumulators. DO NOT CHARGE THE BATTERIES. Charger support (ORCL) Material, housing color and tightness ABS, Yellow, IP20 Weight 400 g.
6.3- Orion receivers (ORR) Industrial Industrial Rail DIN (small model) (large model) (ORRD) (ORRS) (ORRA) Housing material PC-GF Housing color Grey Yellow Grey Tightness IP20 IP65 IP65 Maximum weight 220 g. 350 g. 1200 g. Number of command outputs 3 or 2+1 (1)
Physical unit switched by relay Contactor (for «RM» relay and function «relays») Switching at 230VAC (70VA,cosphi=0,75) 2 x 10 CA2DN LC1D09 Switching at 110VAC, (70VA,cosphi=0,75) 1 x 10 LC1D18 LC2D09 Switching at 48VAC (70VA,cosphi=0,75) 0,5 x 10 Orion - 324501G - 74 -...
315 mA / 250 VAC / T - F2 115VAC Board supplied with 62 mA / 250 VAC / T - F1 160 mA / 250 VAC / T - F1 230VAC - Function relays No protection No protection - «RM» relay Orion - 324501G - 75 -...
R1 and R2. Microswitch JP4 position «RM/R3» relay function «RM» relay «R3» relay Note : The program settings for relay R3 are saved in the event that microswitch is set to the «OFF» position. Orion - 324501G - 76 -...
Step 6 > see chapter «Standby» function time programming (Automatic (Optional) shutdown of transmitter) Proceed to the installation on site by respecting the installation Step 7 recommendations described in chapter Installation and use recommendations Orion - 324501G - 77 -...
ON - ON - ON - ON - ON - ON - ON - ON (11111111 binary = 255 decimal) We strongly recommend that you change this code to ensure the uniqueness of your installation and avoid any unintentional commands from another system which may already be installed. Orion - 324501G - 78 -...
Validate the identity code group by pressing button B2 (or the «On/Off» button if used). Cancel by pressing internal button S1 Compose a code using the 8-cursor DIP_switch Close the housing of the OREV transmitter Orion - 324501G - 79 -...
It is possible that the receiver is associated with an unwanted transmitter. During all the duration of the association procedure, it is recommended not ot used any other Orion transmitter. Orion - 324501G - 80 -...
Page 81
ORRD receiver : set the microswitches to the «OFF» position If no transmitter button is activated during this programming procedure, the receiver parameter settings (buttons / relay association, interlocking and operating mode previously programmed) will not be erased. Orion - 324501G - 81 -...
ORRD receiver : set the microswitch to the «ON» position ORRS ORRA ORRD V1 V2 V3 V1 V2 V3 ORRS and ORRA receivers : Switch on the receiver ORRD receiver : go to the next step Orion - 324501G - 82 -...
Page 83
If other associations are required, repeat the procedure in step N°3 Once you have completed the associations : ORRS and ORRA receivers : switch off the receiver and remove the jumper ORRD receiver : set the microswitch to the «OFF» position Orion - 324501G - 83 -...
2 fl ashes = fi xed channel multi-receiver selection mode 3 fl ashes = auto channel multi-receiver selection mode. Each time the button is pressed, the operating mode is modifi ed. Validate the operating mode by pressing the «On/Off» button. Orion - 324501G - 85 -...
ASSOCIATION METHOD AND PROCEDURE : After you have chosen an identity code (8-cursor DIP_switch) and possibly an identity code group for the OREV transmitter, the transmitter / receivers are successively associated for each receiver (see next page). Orion - 324501G - 86 -...
Page 87
ORRS and ORRA receivers : switch off the receiver and remove the jumpers. ORRD receiver : set the microswitches to the «OFF» position Repeat the association procedure for each receiver to be associated Orion - 324501G - 87 -...
Receiver(s) Receiver(s) Receiver(s) Receiver(s) Channel nb 16 Channel nb 17 Channel nb 1 Channel nb 2 Channel nb 3 Channel nb 11 Ci 157 Ci 157+1=158 Ci 157+2=159 Ci 157+3=160 Ci 157+4=161 Ci 157+12=169 Orion - 324501G - 88 -...
Page 89
ORRS and ORRA receivers : switch off the receiver and remove the jumpers. ORRD receiver : set the microswitches to the «OFF» position Repeat the association procedure for each receiver to be associated Orion - 324501G - 89 -...
Once the receiver is switched ON, only relays programmed with Mode 2 are activated. Changing the relay operating : A transmitter/receiver association must have been realized. This procedure requires transmitter and receiver. Orion - 324501G - 90 -...
Page 91
Once the programming procedure is fi nished : ORRS and ORRA receivers : switch off the receiver and remove the jumper ORRD receiver : set the microswitch to the «OFF» position Orion - 324501G - 91 -...
ORRD V1 V2 V3 V1 V2 V3 ORRS and ORRA receivers : Switch on the receiver ORRD receiver : go to the next step ORRA ORRS ORRD LEDs blink 2 times then go off. Orion - 324501G - 92 -...
The interlocking functions can only be programmed for this receiver on relays belonging to a same group. Example : interlocking is possible between relay R1 and relay R3 but not possible between relays R1 and R6. Orion - 324501G - 93 -...
fl ashing 6 times, the current radio channel number is «06» (433.600MHz). ORRS and ORRA receivers : switch off the receiver and remove the .jumpers. ORRD receiver : set the microswitches to the «OFF» position Orion - 324501G - 96 -...
The value of the radio transmit power level is incremented by 1 each time button B1 is pressed. Validate the radio power level by pressing button B2 (or by pressing the « On/Off » button if used). Cancel by pressing internal button S1 Close the housing of the OREV transmitter Orion - 324501G - 97 -...
5 fl ashes, off, 5 fl ashes etc... = 30s Press to modify the duration, each pressure on the button increments the duration.. Once the desired duration is selected, press the «on/off» button to validate your choice. The transmitter saves the changing. Orion - 324501G - 98 -...
All the receiver parameters (except the radio channel setting) are erased. ORRS and ORRA receivers : switch off the receiver and remove the jumpers. ORRD receiver : set the microswitches to the «OFF» position. Orion - 324501G - 99 -...
fl ash alternately. Clearing and re-programming of the « factory » parameters of the transmitter is completed when the Va and Vb indicator lights go off. Close the housing of the OREV transmitter. Orion - 324501G - 100 -...
A draw resistor should also be used on the controller inputs. Examples of protection system to be used: Receiver output terminal strip Output on AC relay Output on DC relay PLC input (RC circuit ) (freewheel diode) (Draw resistor R=Vdc/Imin(10mA)) Orion - 324501G - 101 -...
8.5- «Multifunction» transmitters equipped with accumulators and charger support (ORCL•) When transmitters are equipped with accumulators, please charge them for approximately 3 hours before a fi rst use. Orion - 324501G - 102 -...
It must never cross through a wall, not even an insulating wall. Note that the best range is obtained by tilting the transmitter as indicated in the diagram below : Transmitter Receiver Orion - 324501G - 103 -...
Page 104
ORRA and ORRS : antenna VUB084 or antenna VUB086 Installation in plastic cabinet ORRD : antenna VUB084 + 90° BNC bend VUB060 Antenna VUB084 + extension 0,5m VUB170 Installation in metal cabinet or antenna VUB086 + extension 0,5m VUB170 Orion - 324501G - 104 -...
To open the ORRS and ORRA connection terminal strips : 1. Vertically insert the screwdriver (fl at tip screwdriver of 1.5 to 3 mm width) in the slot located opposite the wire, 2. Insert the wire, 3. Remove the screwdriver. Orion - 324501G - 105 -...
/ accumulators, the tightening of housing screws the seal (multifunction transmitter OREL). - Clean the transmitter by eliminating any foreign matter. Only use non aggressive cleaning product on base of soapy solution. Orion - 324501G - 106 -...
Page 107
ORRS receiver) is used, check the antenna connection and check that it is clean and free of any oxidation. - Clean the receiver by eliminating any foreign matter. Only use non aggressive cleaning product on base of soapy solution. Orion - 324501G - 107 -...
: - Waste disposal centres, where containers for this purpose are available, - All city halls - Major department stores - As a general rule, with local craftsmen and store keepers providing this service. Orion - 324501G - 108 -...
The warranty shall not apply subsequent to any modifi cations or additions to the equipment performed by the customer without written approval by JAYElectronique. The JAY Electronique responsability during the warranty period is limited to material and construction defects. This warranty comprises repair in the JAY workshops or replacement, free of charge, of parts recognized to be defective following expert inspection by the Jay Technical Department.
Ladeniveau schwach ist. Die Ausrüstung pfl egen, und je nach Betriebsintensität regelmäßig überprüfen. (1) = Die Programmierung einer anderen Funkkanalnummer kann ausschließlich über einen Sender erfolgen, der mit einer «Ein/Aus»-Taste ausgestattet ist. Orion - 324501G - 114 -...
-RTTE : Funkausrüstung und Telekommunikationsterminals (Niederspannung, elektromagnetische Verträglichkeit, funkelektrisches Spektrum). Bitte wenden Sie sich mit allen Fragen bezüglich Installation oder Verwendung der Reihe Orion an unseren Kundendienst (Montag bis Freitag): Tel : +33.(0)4.76.41.44.00 Fax : +33.(0)4.76.41.44.44 Email : customer.service@jay-electronique.com Orion - 324501G...
3 - Betrieb 3.1- Funktionsprinzip Die Serie Orion ermöglicht die Fernsteuerung von einem oder mehreren mit Relais ausgerüsteten Empfängern. Die Kommunikation zwischen Sender und Empfänger erfolgt über Funkwellen auf einem besonderen Kanal mit individueller Verschlüsselung (Identitätscode). Die Funkverbindung wird momentan erstellt, und ist nur bei der Betätigung einer Sendertaste aktiv.
Empfänger unter Spannung steht). Die Jumper für die Codierung der Empfänger ORRS und ORRA müssen für die Herstellung der Brücke verwendet werden, die der gewünschten Programmierung entspricht (die Geräte werden mit mehreren Schaltbrücken geliefert): Jumper Jumper Orion - 324501G - 117 -...
Des weiteren besitzen mit dieser Taste ausgerüstete Sender zwei weitere vom Benutzer programmierbare Funktionen : Das automatische Ausschalten des Senders («Standby»- Funktion) Änderung des Arbeitsfunkkanals Sender ohne Sender mit Ein/Aus-Taste Ein/Aus-Taste Orion - 324501G - 118 -...
Funktionsrelais aktiviert wurde. - Es öffnet sich, falls kein Funktionsrelais aktiv ist oder der Empfänger ausgeschaltet ist oder bei Funkstörungen von mehr als einer Sekunde, wenn einer der Taste des Senders gedrückt ist. Orion - 324501G - 119 -...
Page 120
Einsatzbeispiel des für die Betriebsart «Gemeinsames Relais» auf dem Empfänger ORRS42••• programmierten «RM»-Relais : ORRS 1 2 3 4 5 6 7 8 9 10 11 12 13 Verka- belung außen Steuerung Steuerung Wasserkraftwerk Elektroventile (*) = Antistörungsvorrichtungen Orion - 324501G - 120 -...
Die Sender und Empfänger Orion werden mit Voreinstellung geliefert und können sofort eingesetzt werden. Es wird jedoch empfohlen, diese Einstellungen individuell abzustimmen, um die Einmaligkeit der Anlage sicherzustellen und die gesamte Bandbreite der Funktionen der Serie Orion kennen zu lernen (siehe Kapitel «Konfi guration der Geräte»).
Empfängerrelais aktiviert. Bei Loslassen der Taste wird das Relais deaktiviert.) Zwischenverriegelung gegensätzlicher Keine programmierte Standard-Zwischenverriegelung Manöver (1) = Die Programmierung einer anderen Funkkanalnummer kann ausschließlich über einen Sender erfolgen, der mit einer «Ein/Aus»-Taste ausgestattet ist. Orion - 324501G - 122 -...
Empfängermodelle den abnehmbaren Antennensatz OWR01 für die Benutzung einer abnehmbaren Antenne oder Antennenverlängerung. (5) = Nicht geeignet für einen direkten Anschluss an eine VUB086-Antenne, in diesem Fall eine Verlängerung vom Typ VUB1•• benutzen. Orion - 324501G - 124 -...
(230VAC > 9VDC) mit 3 Akkus AAA geliefert mit 3 Akkus AAA geliefert Zum Laden des Orion Multifunktionssenders mit Akkus folgendes beachten : 1. Ladehalterung an die Stromversorgung anschließen 2. Druck auf die Ein/Aus-Taste (falls vorhanden) zu Sender ausschalten (rote und grüne Konrollleuchte aus).
315 mA / 250 VAC / T - F2 Karte Mit 230 VAC gespeiste 62 mA / 250 VAC / T - F1 160 mA / 250 VAC / T - F1 Karte - Funktionsrelais Kein Schutz Kein Schutz - Relais «RM» Orion - 324501G - 129 -...
Programmierung denen der Relais R1 und R2 entspricht. Position des Microswitch JP4 Funktion des Relais «RM/R3» Relais «RM» Relais «R3» Hinweis : Die Programmierungen des Relais R3 werden beim Schalten des Microswitches in die Position «OFF» gesichert.. Orion - 324501G - 130 -...
(facultative) Zeitverzögerung «Standby»-Funktion programmieren/ändern Schritt Nr.6 > Siehe Kapitel Programmierung der Verzögerungsdauer der (facultative) «Standby»-Funktion (Automatisches Abschalten des Senders) Installation am Standort unter Beachtung der in Kapitel Einrichtungs- Schritt Nr.7 und Benutzungsempfehlungen beschriebenen Installationsregeln Orion - 324501G - 131 -...
ON - ON - ON - ON - ON - ON - ON - ON (11111111 binär = 255 dezimal) Es wird dringend empfohlen, diesen Code zu ändern, um die Unverwechselbarkeit Ihrer Anlage sicher zu stellen und willkürliche Steuerungen bereits vorhandener Systeme zu vermeiden. Orion - 324501G - 132 -...
Bestätigen Sie die Identitätscode-Gruppennummer durch Drücken von Taster B2 (oder den «EIN/AUS»-Taste, sofern vorhanden). oder Abbrechen durch Drücken des internen Tasters S1 Geben Sie mit dem 8-fach DIP-Switch einen Code ein Das Gehäuse des OREV-Senders wieder schließen Orion - 324501G - 133 -...
Tasten/Relais- Zuordnungen, Funkkanals, Tastenkombinationen und Relaisfunktionsweisen gelöscht. Es ist möglich, dass der Empfänger mit einem nicht gewünschten Sender gleichgeschaltet wird. Es wird empfohlen, während des gesamten Gleichschaltungsvorgangs die Verwendung aller anderen Orion-Sender zu unterbrechen. Orion - 324501G - 134 -...
Page 135
Empfänger ORRS und ORRA : Den Empfänger ausschalten und die Kurzschlussbrücken Empfänger ORRD : Microswitches auf Position «OFF» stellen Wenn während des Programmierverfahrens keine Sendertaste betätigt wird wird die Parametrierung des Empfängers (vorher erfolgte Tasten/Relais-Zuordnung, Zwischenverriegelung (Tastenkombination) und Relaisbetriebsweise) nicht gelöscht. Orion - 324501G - 135 -...
Brücke einsetzen. Empfänger ORRD : Microswitch auf Position «ON» stellen ORRS ORRA ORRD V1 V2 V3 V1 V2 V3 Empfänger ORRS und ORRA : Den Empfänger einschalten Empfänger ORRD : Weiter zum nächsten Schritt Orion - 324501G - 136 -...
Page 137
Wenn weitere Verbindungen hergestellt werden müssen, das Verfahren ab Schritt 3 wiederholen Nach Fertigstellung sämtlicher Verbindungen : Empfänger ORRS und ORRA : Den Empfänger ausschalten und der Kurzschlussbrücke entfernen. Empfänger ORRD : Microswitch auf Position «OFF» stellen Orion - 324501G - 137 -...
1 Mal Blinken = Normaler Modus 2 Mal Blinken = Multi-Empfänger-Auswahlmodus mit festem Kanal 3 Mal Blinken = Multi-Empfänger-Auswahlmodus mit automatischer Kanalwahl. Bei jedem Drücken der Taste wird die Betriebsart geändert. Bestätigen Sie die Betriebsart durch Drücken der «EIN/AUS»-Taste. Orion - 324501G - 139 -...
IDC 157+12=169 METHODE UND VERFAHREN FÜR DIE VERBINDUNGSHERSTELLUNG: Nach Wahl eines Identitätscodes (8-facher DIP-Switch) und ggf. eines Identitätscodes für den OREV-Sender werden nacheinander die Verbindungen Sender / Empfänger für jeden Empfänger hergestellt (siehe nächste Seite). Orion - 324501G - 140 -...
Page 141
Der Empfänger hat den Befehl erhalten, die Taster und den Identitätscode des Senders den Funktionsrelais zuzuordnen. Empfänger ORRS und ORRA : Den Empfänger ausschalten und die Kurzschlussbrücken Empfänger ORRD : Microswitches auf Position «OFF» stellen Für jeden zu verbindenden Empfänger die Verbindung wiederholen Orion - 324501G - 141 -...
Empfänger Empfänger Empfänger Empfänger F.kanal Nr. 16 F.kanal Nr. 17 F.kanal Nr. 1 F.kanal Nr. 2 F.kanal Nr. 3 F.kanal Nr. 11 ID-Code 157 IDC 157+1=158 IDC 157+2=159 IDC 157+3=160 IDC 157+4=161 Ci 157+12=169 Orion - 324501G - 142 -...
Page 143
Der Empfänger hat den Befehl erhalten, die Taster und den Identitätscode des Senders den Funktionsrelais zuzuordnen. Empfänger ORRS und ORRA : Den Empfänger ausschalten und die Kurzschlussbrücken Empfänger ORRD : Microswitches auf Position «OFF» stellen Für jeden zu verbindenden Empfänger die Verbindung wiederholen Orion - 324501G - 143 -...
Betriebsart 2 programmierten Relais. Änderung der Relaisbetrieb : Die Sender/Empfängerzuordnung muss bereits erfolgt sein. Bei dem Verfahren zum Ändern der Funktionsweise ist ein Sender und ein Empfänger notwendig. Orion - 324501G - 144 -...
Page 145
Änderungsbefehl nicht ordnungsgemäß ausgeführt wurde. Nach Fertigstellung sämtlicher Verbindungen : Empfänger ORRS und ORRA : Den Empfänger ausschalten und der Kurzschlussbrücke entfernen. Empfänger ORRD : Microswitch auf Position «OFF» stellen Orion - 324501G - 145 -...
Page 146
ORRD V1 V2 V3 V1 V2 V3 Empfänger ORRS und ORRA : Den Empfänger einschalten Empfänger ORRD : Weiter zum nächsten Schritt ORRA ORRS ORRD Die Kontrollleuchten V2 blinken 2 Mal und erlöschen dann. Orion - 324501G - 146 -...
Gruppe 4 : Relais Nr.13 (R13) bis Relais Nr.16 (R16). Die Programmierung der Zwischenverriegelung dieses Empfängers kann nur mit Relais derselben Gruppe erfolgen. Beispiel: Zwischenverriegelung zwischen Relais R1 und Relais R3 möglich, aber nicht zwischen R1 und R6. Orion - 324501G - 147 -...
«Ein/Aus». Der Empfänger muss beim Verfahren eingeschaltet sein, um den Änderungsbefehl des Funkkanals empfangen zu können. Industrielle sender B1 B2 B3 B4 Taste «Ein/Aus» électronique Multifunktions sender Taste «Ein/Aus» électronique électronique électronique électronique Orion - 324501G - 148 -...
Page 149
Sender den neu gewählten Funkkanal auf allen Funkkanälen (01 bis 18) an den Sender, und beide Geräte speichern die Änderung. Das Verfahren ist beendet, wenn beide Kontrollleuchten des Senders Va und Vb erlöschen (ca. 10s). Orion - 324501G - 149 -...
ORRA aus, und V3 ORRS ORRD blinkt 6 mal, der Funkkanal ist also «06» (433.600MHz). Empfänger ORRS und ORRA : Den Empfänger ausschalten und die Kurzschlussbrücken Empfänger ORRD : Microswitches auf Position «OFF» stellen Orion - 324501G - 150 -...
Bei jedem Drücken der Taste B1 wird die Sendeleistungsstufe um den Wert 1 erhöht. Bestätigen Sie die Sendeleistungsstufe durch Drücken von Taster B2 (oder den «EIN/AUS»- Taste, sofern vorhanden). oder Abbrechen durch Drücken des internen Tasters S1 Das Gehäuse des OREV-Senders wieder schließen Orion - 324501G - 151 -...
Auf die Taste drücken, um die Dauer der Zeitverzögerung zu ändern. Jeder Tastendruck inkrementiert die Dauer. Nach erfolgter Wahl der neuen Dauer die Taste «Ein/Aus» betätigen, um die Wahl zu bestätigen. Der Sender speichert die Änderung. Orion - 324501G - 152 -...
Empfänger ORRD, wo die Auffallenden eine Pause kennzeichnen und 5 Mal wiederblinken...). Alle Empfängerparameter (mit Ausnahme des Funkkanals) gelöscht Empfänger ORRS und ORRA : Den Empfänger ausschalten und die Kurzschlussbrücken Empfänger ORRD : Microswitches auf Position «OFF» stellen Orion - 324501G - 153 -...
Taste S1 drücken und ungefähr 10 Sekunden gedrückt halten. Die Kontrollleuchten Va und Vb ddes Senders blinken abwechselnd. Das Löschen und Neuprogrammieren der «werksseitigen» Parametrierung ist abgeschlossen, sobald die Kontrollleuchten Va und Vb erlöschen. Das Gehäuse des OREV-Senders wieder schließen. Orion - 324501G - 154 -...
Elemente angebracht und mit so kurzen Verbindungen wie möglich angeschlossen werden. wird empfohlen, einen Verbrauchswiderstand Automatenengängen zu benutzen. Beispiele für zu benutzende Schutzvorrichtungen: Ausgangsklemme des Empfängers Ausgang AC-Relais Ausgang DC-Relais SPS-Eingang (RC-Kreis) (freie Raddiode) (Verbrauchswiderstand R=Vdc/Imin(10mA) Orion - 324501G - 155 -...
Lasten oder Zwischenrelais einbauen (Nebenkontakte im Schaltschrank für die Leistungssteuerung, zum Beispiel). 8.5- «Multifunktions-Sender» (OREL) mit Akkumulatoren und Ladehalterung (ORCL•) Wenn die Multifunktions-Sender mit Akkus ausgerüstet sind, vor dem ersten Einsatz drei Stunden laden. Orion - 324501G - 156 -...
• hindernisfrei oder mit so wenig Hindernissen wie möglich zwischen Sende- und Empfangspunkten ausgerichtet sein. Sie darf niemals eine Wand durchqueren, selbst wenn diese isolierend ist. Die beste Reichweite wird erhalten, wenn der Sender wie unten dargestellt geneigt wird : Sender Empfänger Orion - 324501G - 157 -...
Anschlussklemmen der Empfänger öffnen : 1. einen Schraubenzieher vertikal (mit fl acher Klinge von 1,5 bis 3 mm Breite) in den Schlitz gegenüber dem Kabel einführen, 2. das Kabel einführen, 3. den Schraubenzieher herausziehen. Orion - 324501G - 159 -...
Senders, und besonders der Funktionstasten und den Zustand der Batterien / Akkus, sowie der oder den Gehäuseschrauben und den Zustand der Dichtung (Multifunktionssender OREL). - Den Sender reinigen und dabei alle Fremdkörper entfernen. Nur nicht aggressive Reinigungsmittel auf Seifengrundlage benutzen. Orion - 324501G - 160 -...
Page 161
- Wenn das Zubehör OWR01 (externer Antennenstecker BNC) benutzt wird, Anschluss der Antenne prüfen und Antenne auf Sauberkeit und Oxidation prüfen. - Den Empfänger reinigen und dabei alle Fremdkörper entfernen. Nur nicht aggressive Reinigungsmittel auf Seifengrundlage benutzen. Orion - 324501G - 161 -...
Sammelbehältern entsorgt werden, die sich an folgenden Stellen befi nden : - In allen Wertstoffhöfen in den dafür vorgesehenen Containern - In allen Rathäusern - In allen grossen Supermärkten - Im allgemeinen bei freiwilligen Händlern und Geschäften. Orion - 324501G - 162 -...
Einwirkungen) zurückzuführen sind. Die Garantie entfällt, wenn der Kunde Veränderungen oder Ergänzungen am Gerät vornimmt, ohne die schriftliche Zustimmung durch unser Unternehmen. Die Haftung des Unternehmens JAY Electronique beschränkt sich während Garantiezeit Materialfehler oder Konstruktionsmängel; sie umfaßt die Reparatur in unserem Werk oder den kostenlosen Austausch defekter Teile nach Begutachtung durch einen unserer «Technischen Dienste».
C - Vues détaillées des récepteurs C - Receivers ORR : detailed views C - Detaillierte Innenansicht des Empfängers ORRS ORRD ORRA V1 V3 V2 Orion - 324501G - 168 -...
Page 169
Rx= Steuerrelais (die Anzahl der Relais schwankt je nach (3) = Sélection du relais par le microswitch JP4. ORR Empfängerversion) Relay selection by JP4 microswitch. Anschlussklemmen Stromversorgung Relaisauswahl durch Microswitch JP4. Kontaktklemmen der Steuerrelais Orion - 324501G - 169 -...
H - List of available radio frequencies H - Liste der verfügbaren Frequenzen RAPPEL Le canal radio des émetteurs et récepteurs Orion peut être modifi é uniquement avec des émetteurs équipés du bouton «marche/arrêt». Si plusieurs radiocommandes travaillent sur le même site, il convient d’utiliser des fréquences radio différentes espacées d’au moins 2 canaux (par exemple canaux 5, 7,...
Page 176
ZAC la Bâtie, rue Champrond F38334 SAINT ISMIER cedex Tel : +33 (0)4 76 41 44 00 - Fax : +33 (0)4 76 41 44 44 www.jay-electronique.com...