Advertisement
Available languages
Available languages
Jäger Direkt GmbH & Co. KG • Hochstraße 6 • 64385 Reichelsheim • Tel.: +49 (06164) 930050 • Fax: +49 (06164) 930069 • e-mail: info@jaeger-direkt.com • Internet: www.opus-schalter.de
Installation and operating instructions
OPUS RADIO PLUS blind actuator one-way FM
for RADIO PLUS transmitters
Art.no.: 561.314
1. Description
The blind actuator controls roller shutters and blinds with limit
switches (230V/50 Hz motors) with the output UP and the
output DOWN .
The Opus
-Radio Plus actuator is controlled by radio signals
®
from Radio Plus transmitters. Each transmitter can simultan-
eously control an unlimited number of actuators.
The transmitters have a fixed address and must be assigned
on a actuator (max. 32 transmitters).
The memory of each actuator is empty when delivered.
Function 1 (standard function) is preset by default in the
actuator of a freshly assigned transmitter.
The actuator's function can be changed by programming
to respond to any assigned transmitter (see Point 6).
2. Mounting
561.314
FUNK Plus
Jalousieaktor 1fach Up
CLR/MODE
µ
µ
230V~
50Hz
L max.600VA
LRN/SET
N N
L
N N
L
Learn mode:
N
N
LED = red
L
Function programming:
LED = green oder orange
M
Mounting and set-up may only be carried out by an
authorised professional.
All works may only be performed once the mains power
supply 230V/50Hz~ has been switched off. Mounting must
adhere to the valid laws, standards and regulations.
The supply line may only be fused with a fuse or circuit
breaker (max. 10A).
For programming, the actuators must be connected to the
mains power supply. The programming is retained even in a
power failure.
NEVER mount the Radio Plus transmitter or actuator in a
metal housing or directly next to large metal objects.
It is also not advisable to mount the actuators on the floor or
close to the floor.
The following points must be observed:
- the valid laws, standards and regulations
- the best available technology at the time of installation.
- the operating instructions of the Radio Plus-modules.
- the fact that operating instructions can only contain general
guidelines and that these must be considered in the context
of a specific system.
Caution!! The Radio Plus-modules must not be used with
devices, which could affect human health or safety, or en-
danger humans, animals or material assets.
561314-Rev01_070122.pdf
GB
3. Technical data
Transmission frequency
Power supply
Fusing the supply lines
Max. switching capacity
Ambient temperature
Storage temperature
Protection level
4. Assigning or deleting Radio Plus transmitters
Opus
-Radio Plus transmitters can be assigned or deleted in
®
the learn mode of the actuator. Learn mode is activated by
pressing the LRN/SET (LED flashes red).
If a button of the transmitter that is to be assigned is pressed
once in learn mode and recognized by the actuator (LED on),
the transmitter has been assigned.
If a button of an already assigned transmitter is pressed once
and recognized by the actuator (LED off), the transmitter has
been deleted.
Caution!! If the button off a transmitter is pressed repeatedly
the transmitter will be alternately assigned or deleted!
CLR/MODE-button
After an Radio Plus transmitter has been assigned or deleted
Parameter setting
the actuator returns to learn mode (LED flashes red) and other
LRN/SET-button
transmitters can be assigned or deleted.
Learn mode and
When no button of an Radio Plus transmitter is pressed, the
Function
actuator leaves the learn mode after approx. 30s independently.
programming
Press the LRN/SET
button briefly
Learn mode
(LED flashes red)
Press the LRN/SET
button briefly
Learn mode OFF
(LED off)
Function 1 (standard function) is preset by default in the
actuator of a freshly assigned transmitter.
If desired, the actuator's function and its parameter can be
changed by function programming (see Point 6) for each
assigned transmitter.
5. Deleting all assigned transmitters
Press the CLR/MODE button and hold it down for approx. 2s.
During this time, the memory is completely deleted (delivery
status). Then, the actuator is in learn mode (LED flashes red).
Press the CLR/MODE
button for longer
All assigned
transmitters deleted
Learn mode
(LED flashes red)
6. Function programming
The Radio Plus actuator's function and its parameter can
868.3 MHz
be changed by function programming each assigned Radio
230 V~ / 50 Hz
Plus transmitter (see Point 4).
Circuit breaker or fuse
(max. 10 A)
600 VA
Function programming is activated by pressing an holding the
LRN/SET button until confirmed (LEDs flash green rapidly).
-20° to +40 C
Function programming can be manually terminated by
-40° to +85°C
activating the CLR/MODE button.
IP 20
Without activating the button on a transmitter, the actuator will
terminate function programming automatically after about 30s.
If function programming is active, a button of the transmitter
must be pressed for recognition, for which the function of
the actuator is to be changed.
Once the transmitter is recognized by the actuator , the actuator
is active (LED flashes orange).
The number of times the LED flashes corresponds to the
actuator's current function. This function can then be changed
by the number of times that the LRN/SET button is activated
(e.g. pressing LRN/SET twice = Function 2).
The parameter setting is accessed in function programming
by activating the CLR/MODE button. Subsequently the actuator
is active (LED flashes green).
Parameter setting can be manually terminated by activating
the CLR/MODE button.
The number of times the LED flashes corresponds to the
parameter currently set for the actuator's current function.
This parameter can then be changed by the number of times
that the LRN/SET button is activated
(e.g. pressing LRN/SET twice = Parameter 2).
Press the LRN/SET
button for longer
Assign/delete transmitter
Press a button of the
Function programming
transmitter once
(LEDs flash green rapidly)
Transmitter assigned
Recognition of transmitter
(LED on)
Press a button of the transmitter
Actuator function 1
Transmitter deleted
(LED off)
Actuator is active
(LED flashes orange)
number of flashing = function
Press the LRN/SET button to
select the function 1-7
number of actuations = function
Press the CLR/MODE
button briefly
Parameter setting
Actuator is active
(LED flashes green)
number of flashing = parameter
Press the LRN/SET button to
select the parameter
number of actuations = function
s. Point 4
Idle state
(LED off)
Press the CLR/MODE
button briefly
GB - 1
Advertisement
