Download Print this page
Sealey AK459DX.V2 Instructions

Sealey AK459DX.V2 Instructions

Gravity & suction feed/air discharge oil drainer

Advertisement

Quick Links

GRAVITY & SUCTION FEED/AIR DISCHARGE OIL DRAINER
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
1.1.
GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
!
Familiarise yourself with the application and limitations of the oil drainer, as well as the potential hazards.
"
WARNING! Disconnect the drainer from the air supply before changing accessories, servicing or performing any maintenance.
!
Maintain the drainer in good condition (use an authorised service agent).
"
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
"
Keep the work area clean, uncluttered and ensure there is adequate lighting.
"
Keep the drainer clean for best and safest performance.
"
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
"
WARNING! While extracting high temperature oils, keep hands, face and body protected using suitable personal protective equipment (PPE).
! !
Keep children and unauthorised persons away from the work area.
"
WARNING! Ensure correct air pressure is maintained and not exceeded.
!
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use, and ensure that all connections are secure.
"
DO NOT extract caustic or flammable products.
#
DO NOT use the drainer for any purpose other than that for which it is designed.
#
DO NOT operate the drainer if any parts are damaged or missing as this may cause failure and/or personal injury.
#
DO NOT stand on the drainer.
#
DO NOT adjust or tamper with the safety valve.
#
DO NOT move the drainer by the hose, or yank the hose from the air supply.
#
DO NOT place attachments close to your face (especially eyes, ears, etc.) and do not point hose at other persons or animals.
#
DO NOT allow untrained persons to operate the drainer.
#
DO NOT operate the drainer when you are tired or under the influence of alcohol, drugs or intoxicating medication.
#
DO NOT leave the drainer operating unattended.
#
DO NOT direct air from the air hose at yourself or others.
#
When not in use disconnect from the air supply, vent reservoir and store in a safe, dry, childproof area.
"
Dispose of waste oil in accordance with local authority regulations.
"
WARNING! DO NOT pollute the environment by allowing uncontrolled discharge of waste oil.
!
DANGER! DO NOT release drain pan clamp lever when there is pressure in the reservoir as pipe and drain pan will be propelled
$ $
upward with force. This could result in damage and/or serious injury.
2.
INTRODUCTION
Steel fabricated 90ltr reservoir. Height adjustable steel drain pan fitted with plastic filter tray. Gravity
feed reservoir with air discharge. Includes quick-release oil dipstick probes, plus adaptors for BMW
and Volkswagen, powered by venturi suction pump. Fitted with reservoir oil level indicator tube.
Heavy-duty wheels and castors for easy mobility.
3.
ASSEMBLY
3.1.1
Fit the venturi pump and gauge assembly to the resevoir tank,
ensure the gasket is properly positioned. Tighten the nut using
a suitable wrench (Fig. 1.1).
3.1.2
Connect the drain hose with the ball valve adaptor on the base
of the resevoir (Fig. 2.1). Secure the hose with the hose clamp
provided.
3.1.3
Connect the drain pan (Fig. 3.1) to the ball valve (Fig. 3.2).
Insert the assembled group into the resevoir tank and tighten
the ring sleeve (Fig. 3D). Adjust the height and lock in position
using the hand wheel lock (Fig. 3E).
INSTRUCTIONS FOR:
AK459DX.V2
Fig. 1
1
Fig. 1
Fig. 2
1
Fig. 3
2
AK459DX.V2 - 1- 160206

Advertisement

loading

Summary of Contents for Sealey AK459DX.V2

  • Page 1 AK459DX.V2 GRAVITY & SUCTION FEED/AIR DISCHARGE OIL DRAINER Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
  • Page 2 Open valve (Fig. 5.1), keeping the probe dipped in oil. As soon as the sump is emptied, close valve (Fig. 5.1). Note! It is also possible to suck hot waste oil while keeping the air connected to the device. Fig. 6 Fig. 5 AK459DX.V2 - 1 - 160206...
  • Page 3 INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode. Sole UK Distributor 01284 757500 www.sealey.co.uk Sealey Group, 01284 703534 Bury St. Edmunds, Suffolk. sales@sealey.co.uk email AK459DX.V2 - 1 - 160206...