Sealey SA17/S.V2 Instructions

Thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Wear eye
instruction protection
manual
1. saFeTY
WarNiNG! ensure Health & safety, local authority, and general workshop practice regulations are adhered to when using this
‰
equipment.
WarNiNG! disconnect from air supply before changing accessories or servicing.
‰
maintain the polisher in good condition (use an authorised service agent).
9
replace or repair damaged parts. use genuine parts only. unauthorised parts may be dangerous and will invalidate the warranty.
9
use in a suitable, clean and tidy work area, free from unrelated materials. ensure that there is adequate lighting.
9
Before each use check pad for condition. if worn or damaged replace immediately.
9
WarNiNG! Always wear approved eye or face and hand protection when operating the polisher.
‰
use face, dust, or respiratory protection in accordance with cosHH regulations.
9
noise level may be high - wear safety ear defenders.
9
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain and/or tie back long hair.
9
Wear appropriate protective clothing and keep hands and body clear of pad.
9
Maintain correct balance and footing. Ensure that the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the work area.
9
ensure workpiece is secure before operating the polisher. never hold a workpiece by hand.
9
Avoid unintentional starting.
9
WarNiNG! ensure that correct air pressure is maintained and not exceeded. recommended pressure is 90psi.
‰
Keep air hose away from heat, oil and sharp edges.
9
check air hose for wear before each use and ensure that all connections are secure.
9
Prolonged exposure to vibration from this polisher may pose a health risk. it is the owner's responsibility to correctly assess the
9
potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
Do NoT use a polishing pad which has a speed rating less than the speed rating of the polisher.
8
Do NoT use the polisher for a task it is not designed to perform.
8
Do NoT operate polisher if any parts are damaged or missing as this may cause failure and/or personal injury.
8
Do NoT carry the polisher by the hose, or yank the hose from the air supply.
8
Do NoT force, or apply heavy pressure to the polisher, let the polisher do the work.
8
Do NoT operate polisher when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
Do NoT carry the polisher with your finger on the power lever.
8
Do NoT direct air from the air hose at yourself or others.
8
When not in use, disconnect from the air supply and store in a safe, dry, childproof location.
9
2. iNTroDucTioN
Polished and well balanced aluminium body with two side handle mounting positions. trigger operated throttle control. supplied with
Ø180mm backing pad.
3. speciFicaTioNs
model no: ..............................................................SA17/S.V2
Pad size: ................................................................. Ø180mm
thread size: ............................................................. 5/8"UNC
free speed : ............................................................. 2500rpm
Air consumption: ......................................................... 5.3cfm
operating pressure: ...................................................... 90psi
inlet size: ...................................................................1/4"BSP
Weight: ............................................................................. 2kg
noise power/pressure: ....................................... 100/89dB(A)
Vibration/uncertainty: ......................................... 2.39/0.7m/s²
Vacuum outlet: .................................................................. n/a
© Jack sealey limited
instructions for
air polisher Ø180mm 2500rpm
model no:
Wear ear Wear
protection protective
gloves
Original Language Version
sa17/s.V2
Wear a mask
sA17/S.V2 | Issue 5(L) 06/10/17