Sprocket Maintaining and Sharpening the Saw Chain Maintenance and Care Main Parts Specifications This instruction manual is protected by copyright. All rights reserved, especially the rights to reproduce, translate and process with electronic systems. MS 193 T, MS 193 TC...
STIHL's philosophy is to continually This Instruction Manual refers to a improve all of its products. For this Intake air baffle: summer STIHL chain saw, also called a machine reason we may modify the design, operation in this Instruction Manual.
Observe all applicable local safety Wear proper protective clothing and Persons with pacemakers only: The regulations, standards and ordinances. equipment. ignition system of your chainsaw produces an electromagnetic field of a very low intensity. This field may MS 193 T, MS 193 TC...
Page 6
Always stop the engine, engage the (headscarf, cap, hard hat, etc.). technically equivalent components that chain brake and fit the chain guard have been approved by STIHL for this (scabbard) before carrying the saw short Wear suitable safety machine. If you have any questions in distances.
Page 7
To reduce the risk of injury pump (on machines so equipped). If from the rotating chain, check that the cutting attachment is not touching any object or the ground . MS 193 T, MS 193 TC...
Page 8
Mufflers with a To reduce the risk of accidents, take a catalytic converter can become break in good time to avoid tiredness or particularly hot. exhaustion. MS 193 T, MS 193 TC...
Page 9
Hand protection (wearing warm accidents and damage to the machine. If – a catalytic converter. you have any questions in this respect, gloves) consult a servicing dealer. – Work breaks MS 193 T, MS 193 TC...
Kickback occurs when the saw is suddenly thrown up and back in an – To check the chain tension uncontrolled arc towards the operator. – To retension the chain – To replace the chain – For remedying malfunctions MS 193 T, MS 193 TC...
Page 11
The reaction of the chain pulls the saw forward – to reduce this risk, – Be aware of the location of the guide always engage the spiked bumper bar nose at all times. securely in the tree or limb. MS 193 T, MS 193 TC...
You have to take the full weight of the brake to lock the chain or shut off the saw – increased risk of accidents. engine before moving the saw to another position in the tree. MS 193 T, MS 193 TC...
(2) at the tension side (B) – the saw will otherwise pinch or kick back. If not otherwise possible, make the bucking cut from the bottom upwards (underbuck) – be wary of pushback. MS 193 T, MS 193 TC...
(10). Fitting the Chain Unscrew the nut (5) and remove the WARNING cover (6). Wear work gloves to protect your hands from the sharp cutters. MS 193 T, MS 193 TC...
A new chain has to be retensioned more Check chain tension frequently – often than one that has been in use for see chapter on "Operating some time. Instructions". Check chain tension frequently – see chapter on "Operating Instructions". MS 193 T, MS 193 TC...
Engine Oil can quickly make the fuel mix unusable. gasoline vapor. If you mix the fuel yourself, use only STIHL MotoMix may be stored for up to STIHL two-stroke engine oil or another STIHL MotoMix 2 years without any problems.
The marks on the tank cap and fuel tank STIHL recommends you use the STIHL are then in alignment. filler nozzle for fuel (special accessory). Fill up with fuel. MS 193 T, MS 193 TC...
Biological chain oil must be resistant to Right: Bottom of cap in correct posi- aging (e.g. STIHL BioPlus), since it will tion – inner mark is under the otherwise quickly turn to resin. This grip. It is not in line with the results in hard deposits that are difficult outer mark.
STIHL recommends you use the STIHL about 2 to 3 minutes. filler nozzle for chain oil (special accessory). After breaking in the chain, check chain tension and adjust if necessary – see Close the tank cap. "Checking Chain Tension". MS 193 T, MS 193 TC...
STIHL recommends that you Pull the hand guard back towards have servicing and repair work carried the front handle. out exclusively by an authorized STIHL servicing dealer. Maintain the following servicing intervals: MS 193 T, MS 193 TC...
Setting the Master Control Lever To move the Master Control lever from the normal run position (F) to starting throttle (n), press down the throttle trigger lockout and squeeze the throttle MS 193 T, MS 193 TC...
Page 22
Do not pull out the same time. Set Master Control starter rope to full length – it might lever (4) to starting throttle otherwise break. position (n). Set choke lever to required position. MS 193 T, MS 193 TC...
Page 23
(with Plug". chain brake disengaged) until it reaches normal operating Set Master Control lever to the temperature. starting throttle position (n) – even if the engine is cold. Now start the engine. MS 193 T, MS 193 TC...
Slacken off the chain if you have retensioned it at operating Check chain tension frequently temperature during work. A new saw chain must be retensioned more frequently than one that has been in use already for an extended period. MS 193 T, MS 193 TC...
Measure groove depth – using the measuring tool on the file gauge (special accessory) – in the area with the greatest wear Chain type Chain pitch Minimum groove depth Picco 1/4“ P 4.0 mm Rapid 1/4“ 4.0 mm MS 193 T, MS 193 TC...
If filter is caked with dirt: Wash the filter with STIHL universal cleaner or in a clean, non- flammable solution (e.g. warm soapy water) and then dry. NOTICE Do not use a brush to clean the fleece filter. MS 193 T, MS 193 TC...
(even though standard setting of low more than 3/4 turn). speed screw is correct) Turn the low speed screw (L) Idle setting is too lean clockwise as far as stop, then turn it back 1/4 turn. MS 193 T, MS 193 TC...
Open the twist lock (1) in the carbonized, fit a new one. direction of the arrow. Refit the spark arresting screen. Remove the carburetor box cover (2). Fit the baffle plate. MS 193 T, MS 193 TC...
Arcing may occur if the adapter nut (1) is loose or missing. Working in an easily combustible or explosive atmosphere may cause a fire or an explosion. This can result result in serious injuries or damage to property. MS 193 T, MS 193 TC...
It is best to use two saw chains in rotation with one sprocket. STIHL recommends the use of original STIHL sprockets to ensure correct operation of the chain brake. Loosen the clutch hexagon clockwise (left-hand thread). Unscrew the clutch. MS 193 T, MS 193 TC...
The chain pitch marking (a) is embossed Sharpening angle increased vibration load, unsatisfactory in the area of the depth gauge of each STIHL saw chains are sharpened with a cutting results and increased wear. cutter. 30° sharpening angle. Ripping chains, Clean the saw chain which are sharpened with a 10°...
Page 32
The depth gauge determines the depth guide bar) in accordance with the to which the cutter penetrates the wood specified angle – according to the and thus the chip thickness. MS 193 T, MS 193 TC...
Page 33
– if the depth gauge gauge protrudes past the file gauge, the depth gauge must be reworked MS 193 T, MS 193 TC...
Page 34
5605 007 1029 0.404 (10.26) 5.5 (7/32) 5605 772 5506 5605 750 4330 1106 893 4000 0814 252 3356 5605 007 1030 consisting of file holder with round file, taper square file and file gauge MS 193 T, MS 193 TC...
Lubricating oil tank Clean Chain lubrication Check Check, pay attention to sharpness Saw chain Check chain tension Sharpen Check (wear, damage) Clean and turn over Guide bar Deburr Replace Chain sprocket Check Clean Air filter Replace MS 193 T, MS 193 TC...
Page 36
Replace STIHL recommends STIHL servicing dealers During initial use of professional chain saws (with a power output of 3.4 kW or more), tighten the cylinder block screws after 10 to 20 hours of operation MS 193 T, MS 193 TC...
16 Oilomatic chain 17 Spiked bumper 18 Fuel filler cap 19 Oil filler cap 20 Hand guard 21 Handlebar 22 Starter grip 23 Choke lever 24 Manual fuel pump 25 Ring for rope Serial number MS 193 T, MS 193 TC...
3.4 kg Picco Duro 3 (63 PD3) Type 3612 STIHL single cylinder two-stroke engine Pitch: 3/8" P (9.32 Cutting Attachment MS 193 T, MS 193 TC Drive link gauge: 1.3 mm Actual cutting length may be less than Displacement: 30.1 cc 1/4"...
Authorisation and Restriction of Chemical substances. For information on compliance with the REACH regulation (EC) No. 1907/2006 see www.stihl.com/reach. Exhaust Emissions The CO value measured in the EU type approval procedure is specified at www.stihl.com/co2. MS 193 T, MS 193 TC...
Displacement: 30.1 cc replacement parts which have been accessories and packaging to an approved by STIHL for this power tool or approved disposal site for environment- conforms to the relevant provisions of are technically identical. Only use high- friendly recycling.
Page 41
ANDREAS STIHL AG & Co. KG Produktzulassung (Product Licensing) The year of manufacture and serial number are applied to the product. Done at Waiblingen, 28.10.2016 ANDREAS STIHL AG & Co. KG Thomas Elsner Director Product Management and Services MS 193 T, MS 193 TC...
Need help?
Do you have a question about the MS 193 T and is the answer not in the manual?
Questions and answers