1. Manuals
  2. Brands
  3. FDC Manuals
  4. Indoor Fireplace
  5. ENIGMA II SLIMLINE
  6. Owner's manual

FDC ENIGMA II SLIMLINE Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ENIGMA II SLIMLINE
Owner's Manual
INCLUDES USER, INSTALLATION & MAINTENANCE
INSTRUCTIONS
Please read these instructions carefully before you start
using the appliance
Keep this booklet handy for future reference
This appliance is
for use in GREAT BRITAIN or
IRELAND only
AN FDC (UK LTD PRODUCT
LT4934 (1:01/08)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ENIGMA II SLIMLINE and is the answer not in the manual?

Questions and answers

Related Manuals for FDC ENIGMA II SLIMLINE

Summary of Contents for FDC ENIGMA II SLIMLINE

  • Page 1 INCLUDES USER, INSTALLATION & MAINTENANCE INSTRUCTIONS Please read these instructions carefully before you start using the appliance Keep this booklet handy for future reference This appliance is for use in GREAT BRITAIN or IRELAND only AN FDC (UK LTD PRODUCT LT4934 (1:01/08)

  • Page 2: Table Of Contents

    ENIGMA II SLIMLINE Owner's Manual CONTENTS PAGE USERS INSTRUCTIONS SECTION ONE Important Information SECTION TWO Operating the Appliance SECTION THREE Fuel Bed Layout SECTION FOUR Cleaning SECTION FIVE General Points INSTALLATION INSTRUCTIONS SECTION SIX Appliance Data SECTION SEVEN Regulations & Warnings...

  • Page 3: Enigma Ii Slimline

    ‘hazardous waste and should be disposed of at a site licensed for the disposal of industrial waste. • The ENIGMA II SLIMLINE is a decorative fuel effect appliance with a radiant heat conserver box for improved efficiency. •...

  • Page 4: Users Instructions

    Important Information Continued INTRODUCTION The ENIGMA II SLIMLINE incorporates a single gas control, which selects ignition pilot, low or high settings. It is operated via a control knob located behind the ash pan cover. The appliance incorporates a safety device in the form of an Oxygen Depletion System, which constantly monitors the oxygen in the room and will cause the fire to switch off if the oxygen level reduces, for instance due to insufficient ventilation or a blocked flue.

  • Page 5: Section Three

    ENIGMA II SLIMLINE Users Instructions SECTION THREE Fuel Bed Layout It is important that all the fuel bed and moulded shapes are positioned as shown in these instructions. Two Alternative Fuel beds are available: - A) Coal B) Pebble Identify the fuel bed and assemble as shown below.
  • Page 6 ENIGMA II SLIMLINE Users Instructions SECTION THREE Fuel Bed Layout Continued • Place six coals on the top of the front matrix as shown. Arrange to coals to have rough sides forward and make sure that they are stable in their positions.
  • Page 7 ENIGMA II SLIMLINE Users Instructions SECTION THREE Fuel Bed Layout It is important that all the fuel bed and moulded shapes are positioned as shown in these instructions. PEBBLE FUEL BED Some soot deposits will form on the pebbles, this is perfectly normal and adds to the realism of the appliance.
  • Page 8 ENIGMA II SLIMLINE Users Instructions SECTION THREE Fuel Bed Layout Continued • Place five large pebbles as shown. So that they sit on the Front Matrix in the indents provided. Check that they are stable against the rear matrix by putting slight pressure on them with your fingers.

  • Page 9: Section Four

    Low setting, this is quite normal and does not affect the operation of the appliance. It is advised that the ENIGMA II SLIMLINE OR III Lo fire is serviced annually this is more likely to provide trouble-free operation.

  • Page 10: Installation Instructions

    ENIGMA II SLIMLINE Installation Instructions SECTION SIX Appliance Data Category of appliance: Category Overall dimensions: Height 605mm (or 555mm for the Lo version) Width 505mm Forward Projection: 75mm, (From fireplace opening including fret.) Weight: 11kg (Boxed excluding fret) 16.5kg (with fret) 9.5kg (Unboxed excluding fret) 15kg (with fret)
  • Page 11 ENIGMA II SLIMLINE Installation Instructions SECTION SEVEN Regulations and Warnings Cont. THE FOLLOWING ARE RELEVANT CODES OF PRACTICE AND BRITISH STANDARDS: - BS 5871 BS 8303 BS 5440 PART 1 BS 1251 BS 6891 BS 6461 PARTS 1 AND 2...

  • Page 12: Section Eight

    ENIGMA II SLIMLINE Installation Instructions SECTION EIGHT Siting the Appliance Spacers are available in the following sizes 42mm, 30mm and 20mm these may be used to reduce the minimum depth required. The fire can be installed in the following flues and locations: -...

  • Page 13: Clearances At Side Of Fire

    ENIGMA II SLIMLINE Installation Instructions SECTION EIGHT Siting the Appliance Continued • CLASS TWO Fabricated metal A double-walled or insulated metal flue box built to the requirements of BS 715 with a minimum diameter of 125 mm (5 ins) and a minimum effective overall height of 3 metres (10 ft).

  • Page 14: Section Nine

    ENIGMA II SLIMLINE Installation Instructions SECTION NINE To Install the Appliance CHECKING THE FLUE AND FIRE OPENING • Check that the chimney conforms to the required specifications as previously stated. Examine the condition and carry out any remedial work. •...

  • Page 15: Gas Soundness Test

    ENIGMA II SLIMLINE Installation Instructions SECTION NINE To Install the Appliance Continued OPTIONAL CABLE FIXING SYSTEM FIX 4 OFF EYE IN POSITIONS (for use when fixing to 18" openings or when it is SHOWN desirable not to drill the fireplace fascia) it may not be possible to use with some pre-cast flues.

  • Page 16: Section Ten

    ENIGMA II SLIMLINE Installation Instructions SECTION TEN Checking Operation of Fire Checking Product Clearance • Check satisfactory CLOSE ALL DOORS AND WINDOWS, LEAVE FIRE BURNING FOR TEN MINUTES clearance combustion POSITION HEAD OF SMOKE MATCH UNDER FIRE OPENING AS SHOWN...

  • Page 17: Replacement Of Gas Control

    ENIGMA II SLIMLINE Maintenance Instructions SECTION ELEVEN Maintenance • Servicing should be carried out annually by a competent person such as a CORGI- registered person in accordance with the relevant regulations, to ensure the safe and correct operation of the appliance.

  • Page 18: Maintenance Instructions

    ENIGMA II SLIMLINE Maintenance Instructions SECTION SIX Maintenance Cont. Replacement of Injector Repeat operations 1-4 for removal of gas control. Remove the two screws retaining the burner bar. Remove the silencer Undo injector Lock nut and compression nut and remove the injector.
  • Page 19 Important For future reference we suggest you record the following details here, and keep the receipt as proof of purchase. This information may be asked for when you contact the helpdesk. Enigma II Slimline Serial No. Model: This information can be found on the label attached to the packaging and on the data badge, which is located on the appliance flange, top right behind trim.
  • Page 20 LT4934 (1:01/08)
  • Page 21 LT4934 (1:01/08)
  • Page 22 LT4934 (1:01/08)
  • Page 23 Post Code TELEPHONE No. PRODUCT DETAILS Model: Enigma II Slimline Serial No. Date of Purchase This information can be found on the label attached to the packaging and on the data badge, which is located on the appliance flange, top right behind trim.
  • Page 24 ENIGMA II SLIMLINE Packing – Coal ENIGMA II SLIMLINE Packing – Pebble Serial Serial Product Product A0007 A0008 ID Label ID Label Prefix Prefix Fire Box Labels Fire Box Labels Spillage (Pair) Spillage (Pair) Data Badge Data Badge Fire Box Grommet...

Table of Contents