Download Print this page

Honeywell MN6105VAV Installation Instructions Manual

5 nm vav actuator
Hide thumbs

Advertisement

Quick Links

MN6105VAV 5 Nm VAV Actuator
NON-SPRING RETURN DIRECT-COUPLED
DAMPER ACTUATOR FOR FLOATING CONTROL
GENERAL
Replacement actuator, only for use with Spyder and
Stryker controllers with integral actuators.
This non-spring return direct-coupled actuator provides
floating control of VAV units.
It provides reliable control for air damper applications with
up to 10 sq ft (0.9 sq m) / 44 lb-in. (5 Nm) (seal-less
damper blades; air friction-dependent).
FEATURES
• Declutch for manual adjustment.
• Adjustable mechanical end limits.
• Mountable in any orientation.
INSTALLATION INSTRUCTIONS
SPECIFICATIONS
Supply voltage:
MN6105: 24 Vac -15%/+20%, 50/60 Hz.
Nominal voltage:
MN6105: 24 Vac, 50/60 Hz.
All values stated herein after apply to operation under
nominal voltage conditions.
Power consumption:
MN6105: 5 VA / 2 W.
Ambient limits:
Ambient operating limits: -5...+122° F (-20...+50° C).
Ambient storage limits: -22...+176° F (-30...+80° C).
Relative humidity: 5...95%, non-condensing.
Lifetime:
Full strokes: 60000.
Repositions: 1.5 million.
Mounting:
Round damper shaft: 3/8...1/2 in. (9.5...12.7 mm).
Square damper shaft: 1/4...1/2 in. (6.4...12.7 mm);
45° steps.
Shaft length: min. 1-5/8 in. (41.3 mm).
Torque rating: 44 lb-in. (5 Nm).
Runtime for 90°:
MN6105: 90 sec (60 Hz Vac).
Rotation stroke: 95° + 3°.
Approvals: cULus, CE
UL listing categorization:
Action: Type 1 Operating Control
Pollution degree: 2
Impulse voltage: 330 V
Impedance protected motor
INSTALLATION
Some Spyder and Stryker controllers include a direct-
coupled actuator with declutch mechanism, which is
shipped hard-wired to the controller.
The actuator mounts directly onto the VAV box damper
shaft and has up to 44 lb-in. (5 Nm) torque, 90-degree
stroke, and 90 second timing at 60 Hz. The actuator is
31-00150EF-03

Advertisement

loading

  Related Manuals for Honeywell MN6105VAV

  Summary of Contents for Honeywell MN6105VAV

  • Page 1 MN6105VAV 5 Nm VAV Actuator NON-SPRING RETURN DIRECT-COUPLED DAMPER ACTUATOR FOR FLOATING CONTROL INSTALLATION INSTRUCTIONS SPECIFICATIONS Supply voltage: MN6105: 24 Vac -15%/+20%, 50/60 Hz. Nominal voltage: MN6105: 24 Vac, 50/60 Hz. All values stated herein after apply to operation under nominal voltage conditions.
  • Page 2: Ordering Information

    TRADELINE® Catalog or price sheets for complete ordering number. If you have additional questions, need further information, or would like to comment on our products or services, please write or phone: 1. Your local Honeywell Environmental and Combustion Controls Sales Office (check white pages of your phone directory).
  • Page 3 MN6105VAV 5 NM VAV ACTUATOR Installing the New Actuator desired amount of rotation. Adjust the two set screws closer together to reduce the rotation 1. Install new actuator by inserting the anti-rotation travel. end below the foam block in the bottom of the hous- c.
  • Page 4: Panel Mounting

    By using this Honeywell literature, you agree that Honeywell will have no liability for any damages arising out of your use or modification to, the literature. You will defend and indemnify Honeywell, its affiliates and subsidiaries, from and against any liability, cost, or damages, including attorneys’...
  • Page 5: Spécifications

    Servomoteur pour VAV 5 Nm MN6105VAV MOTEUR DE REGISTRE À ACCOUPLEMENT DIRECT SANS RES- SORT DE RAPPEL POUR COMMANDE À FLOTTEUR INSTRUCTIONS D'INSTALLATION SPÉCIFICATIONS Tension d'alimentation : MN6105 : 24 V ca, -15 %/+20 %, 50/60 Hz. Tension nominale : MN6105 : 24 V ca, 50/60 Hz.
  • Page 6: Informations Relatives Aux Commandes

    Si vous avez d'autres questions, si vous avez besoin de renseignements supplémentaires ou si vous voulez nous donner vos commentaires sur nos produits et services, veuillez écrire ou appeler : 1. À votre bureau local des ventes de Honeywell Environmental and Combustion Controls (consultez les pages blanches de votre répertoire téléphonique).
  • Page 7 SERVOMOTEUR POUR VAV 5 NM MN6105VAV Installation servomoteur neuf b. Le servomoteur est livré avec les vis de réglage de butée mécanique de fin de course réglées à 1. Posez le nouveau moteur en insérant l'extrémité une rotation de 95°. Réglez les deux vis de antirotation sous le bloc de mousse situé...
  • Page 8 Vous défendrez et indemniserez Honeywell, ses sociétés affiliées, filiales pour et contre toute responsabilité, frais ou dommages, y compris les honoraires d'avocats, résultant de quelque manière, ou survenant en connexion avec toute modification à la documentation de votre part.