Chengdu Ebyte Electronic Technology Co.,Ltd E840-DTU(4G-02E) User Manual E840-DTU(4G-02E ) is developed for serial port devices and network servers to transmit data to each other through a network.It is a LTE-FDD/WCDMA/GSM wireless communication data transmission modem with diversity receiving function, supporting LTE-FDD, DC-...
1. Product overview 1.1 Introduction E840-DTU (4G-02E) is an LTE digital transmission module product launched by E-Tech. The software of this product is fully functional and covers most common application scenarios. Users can implement serial-to-network server through simple setup. Two-way data transparent transmission.
+OK=E840-DTU(4G-02E)_V1.0 Transmit:AT+SOCK2=1,TCPC,116.62.42.192,31687 //open SOCK2 and configure the network server parameters that SOCK2 will connect to (the parameter used here is Ebyte test server, not recommended for users) Transmit:AT+LINKSTA2 //read if SOCK2 has started connection with server +OK=Connect Transmit:AT+POTOCOL=ON...
Page 13
3、 High speed mode The E840-DTU(4G-02E) is designed with a separate high-speed mode. In this mode, both the network and the device can transmit any packet length data, such as file, picture, and video. Configure/query the high-speed mode state through the AT+HSPEED command. After the high-speed mode is enabled, the device can transmit any packet length data at 230400 serial port baud rate and below.
Page 15
E840-DTU(4G-02E) User Manual 6)Click on the server to run RF.exe to test the file, as shown below: In summary, the E840-DTU(4G-02E) completes the remote transfer of files from the serial port to the network server. 4、SMS function E840-DTU(4G-02E) can support SMS sending and receiving, SMS remote configuration function (inserted SIM card needs to support SMS service).
Page 18
: 01 06 00 01 00 01 19 CA (ModbusT RTU); Note: In the Modbus TCP standard protocol, the transaction element identifier needs to be specified. In E840-DTU- (4G-02E), the user can configure the value through AT+MTCPID, and when the value is configured to 0, the receiving end All data conforming to the Modbus TCP protocol will be parsed, otherwise only packets with the same application packet identifier and device configuration identifier will be converted.
Page 19
The AT+EBTIOT command is used to set whether the module enables the transparent transmission function of the EBYTE cloud platform, after it is turned on, the information such as the heartbeat and registration packet configured by the user will be invalid. The user only needs to set the forwarding relationship of the corresponding device to the platform to implement the device.
Page 22
Chengdu Ebyte Electronic Technology Co.,Ltd E840-DTU(4G-02E) User Manual EBTIOT set/inquire to enable Ebyte IoT Cloud Platform CREG Inquire if it is registered to network Inquire signal strength CPIN Inquire SIM card status POTOCOL set/inquire if protocol transmission mode starts set/inquire serial port parameter(9600,8,N,1)
Page 27
POTOCOL =<data><CR> return:<CR><LF>+OK<CR><LF> Parameters: data status ON Turns on the transmission of the EBYTE protocol OFF Turns off the he transmission of the EBYTE protocol AT+ UARTEX(extending command) function: Set/inquire serial port parameter(AT+UART is for configuring baud rate and parity only)...
Only the first Socket effective link is valid, and the protocol distribution data is not supported. After the EBYTE cloud transparent transmission function is enabled, the high-speed mode is invalid. ...
Chengdu Ebyte Electronic Technology Co.,Ltd E840-DTU(4G-02E) User Manual 5. Important Statement All rights to interpret and modify this manual belong to Ebyte. This manual will be updated based on the upgrade of firmware and hardware, please refer to the latest version.