Adjusting The Basic Picture Quality; Activating The Black Stretch; Activating The Mpeg Nr (Noise Reduction); Activating The Dnr (Digital Noise Reduction) - Toshiba 57X3000A Owner's Manual

Adjusting the basic picture quality

1
M then press Y or Z to display the
In Digital TV, press
TV set up then press Q.
2
Press Y or Z to display the PICTURE menu.
3
In Analog TV, press M and Y or Z to display the
PICTURE menu.
PICTURE
Picture settings
3D Color management
Base color adjustment
Active Backlight Control
Cinema mode
MENU Ba k EXIT
4
Press V or U to select the Picture settings menu, then
press Q.
Pi ture settings
Ba k light
Contrast
Brightness
Color
Tint
Sharpness
MENU EXIT
Ba k
5
Press V or U to select an item you want to adjust, then
press Y or Z to adjust the settings as required.
Contrast
Y
Selection
Back light darker
Contrast lower
Brightness darker
Color paler
Tint reddish
Sharpness softer
Notes:
• The Tint may only be adjusted on NTSC signal.
• In the PC input mode (- page 25), Color, Tint and
Sharpness modes are not available.

Activating the black stretch

This function increases the strength of dark areas of the picture
which improves definition.
1
From the Picture settings menu, press V or U to
select Black stretch on the 2nd page.
Pi ture settings
Bla k stret h
MPEG NR
DNR
Color Temperature
MENU EXIT
Ba k
2
Press Y or Z to select On or Off.
Black stretch
Note:
In the PC input mode (- page 25), this mode is not available.
20
Using the TV's features (General)
,
OK
Off
On
On
Wat h TV
1/2
100
100
50
50
0
0
Wat h TV
100
Z
Pressing
brighter
higher
brighter
deeper
greenish
sharper
2/2
On
Low
Auto
Cool
Wat h TV
On

Activating the MPEG NR (Noise Reduction)

If the receiving signal of MPEG is a mosquito (grained) noise
depending on the compression and conversion, the noise may
be reduced when using this function.
1
From the Picture settings menu, press V or U to
select MPEG NR on the 2nd page.
2
Press Y or Z to select Off, Low, Middle or High.
MPEG NR
Note:
In the PC input mode (- page 25), this mode is not available.
Activating the DNR (Digital Noise
Reduction)

- analog only -

If the receiving signal is weak and the picture is blurry, the
picture may be improved when using this function.
1
From the Picture settings menu, press V or U to
select DNR on the 2nd page.
2
Press Y or Z to select Auto, Off, Low, Middle or High.
DNR

Selecting the color temperature

You can change the tone of the picture by selecting from three
preset color temperatures: Cool, Normal or Warm.
1
From the Picture settings menu, press V or U to
select Color Temperature on the 2nd page.
2
Press Y or Z to select mode you prefer.
Color Temperature
Cool: Lends a blue hue to the picture.
Normal: Neutral
Warm: Lends a red hue to the picture.

Adjusting the color management

You can adjust the picture color quality by selecting from 6
base color adjustments : Red, Green, Blue, Yellow,
Magenta or Cyan.
1
Press M, then press Y or Z to display the PICTURE
menu.
2
Press V or U to select 3D Color management, then
press Y or Z to select On.
3D Color management
3
Press V or U to select Base color adjustment.
4
Press Q, then press V or U to select an item you want
to adjust.
Base olor adjustment
Hue
Red 0
Green 0
Blue 0
Yellow 0
Magenta 0
Cyan 0
Reset
MENU Ba k EXIT
High
Auto
Cool
On
Saturation Brightness
0 0
0 0
0 0
0 0
0 0
0 0
OK
Wat h TV