Centrometal CentroPelet Z6 Technical Instructions
  1. Manuals
  2. Brands
  3. Centrometal Manuals
  4. Stove
  5. CentroPelet Z6
  6. Technical instructions

Centrometal CentroPelet Z6 Technical Instructions

Hide thumbs

Advertisement

Table of Contents

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CentroPelet Z6 and is the answer not in the manual?

Questions and answers

Related Manuals for Centrometal CentroPelet Z6

Summary of Contents for Centrometal CentroPelet Z6

  • Page 2 Dear Customer, ignition of the device as it not only carries out the installation perfectly but also verifies the regular operation of it. installation, use and maintenance. animals. believed opportune. when the device is operating. All our stoves are trial lighted on the construction line. In the event of a fire, disconnect the power supply, use an extinguisher and call the fire fighters if necessary.
  • Page 3 Norms and declarations of conformity amendments; facturer; amendments; place; pellets with a diameter of 6 mm and a maximum length of 30 mm of the type recommended by the manufacturer. Safety information stove the discharge tubes must be connected with the flue; container must never be removed;...
  • Page 4 Charge pellet a door. of pellets touch any hot surfaces. operating in particular: Instructions for safe and efficient use provided being under supervision of someone responsible is installed. animals; protection. stove is in operation.

  • Page 5: Operating Area

    Operating area local national standards. 10 cm (A) standards. Min. It is not permissible to install the stove in bedrooms, bathrooms, or in a room where another heating appliance is installed (fireplace, stove etc.) which does not have its own independent air intake.
  • Page 6 Connection to the flue pipe Connection to an external flue with insulated or double-wall pipe Connection to the flue pipe Fig. 2: connection to the Fig. 3: connection to an flue pipe. external flue with insulated or double-wall pipe.
  • Page 7 Fireplace flue gas Distance to objects 10 cm 30 cm The chimney cap 100 cm suitable platform Fig. 5: characteristics of chimney...

  • Page 8: Control Board

    Control board AL C AL F Stove setting How to change the wished room temperature Display keys and functions value of 1. AL C AL F on or off. How to change the working power seconds. AL C AL F...
  • Page 9 Remote control (if any) control offers some functions minutes. - press remote control must be confirmed OFF1 OFF2 functioning mode:...
  • Page 10 Change the temperature Change the power Automatic power function...
  • Page 11 Function chrono-thermostat (available only through the remote control) AL C AL F Automatic switching off OFF1 and off must be set when the remote control is Off; you will miss the set time for the automatic switching on or off. Once the power supply is back, please program the stove again using the remote control;...

  • Page 12: Display Information

    Always clean the brazier before starting an automatic switching on in order to avoid any possible missed starts up which would damage your stove and the environment. Replace the batteries of the remote control programming is on. and -. Display information “OFF”...

  • Page 13: Technical Specification

    Technical Specification Uscita Fumi Aspirazione Aria TOLLERANZE GENERALI DI LAVORAZIONE TOLLERANZE GENERALI DI LAVORAZIONE Materiale Materiale 4705001 4705001 DIMENSIONI LINEARI DIMENSIONI LINEARI GRADO DI GRADO DI Peso Peso PRECISIONE FINO A PRECISIONE 1000 DA FINO A 2000 OLTRE 1000 DA 2000 OLTRE 41547 g...
  • Page 14 CENTROPELET Z6 It is recommended that the control of emissions after installation. Pellet For our stoves use pellets diameter 6 mm, length 30 mm and a maximum of 8% moisture. Store the pellets away from heat sources and not in...
  • Page 15 Stove start up Remove any components which might Before lighting a small amount of smoke burn from the firebox and from the glass may fill the combustion chamber. (various instructions and adhesive labels). Charge pellet Authorized Service Centre installation and the first ignition of the device as it not only carries out the installation perfectly but also verifies the regular operation of it.

  • Page 16: Alarm Signals

    Alarm signals temperature is broken or not connected. again. settings. Regular checks should be carried out by the user, who should only contact the Authorized Assistance Center " if no solution is found. assistance.
  • Page 17 Maintenance and cleaning of the stove Ash box accidental contact. performed more or less Follow carefully the following cleaning instructions. Failure follow these instructions could create problems with the operation of the stove. Cleaning the glass Cleaning the brazier and brazier support of pellets used.
  • Page 18 It is necessary to daily clean the brazier and often clean the ash box. The lack of cleanliness can prevent the starting of the times, call in qualified personnel; stove, causing damages to the stove itself and to the environment (possible emission of unbrunt material and soot).

  • Page 19: Maintenance And Cleaning

    Maintenance and cleaning All cleaning of all parts must be carried out with the stove completely cold and unplugged to avoid burns and thermal shock. The stove does not need much maintenance if used with certified quality pellet. The need for maintenance varies depending on the conditions of use (switching on and off repeatedly) and depending on the performance required.

  • Page 20: Safety Devices

    Safety devices monitors Reduction motor: Flue gas temperature sensor: significant back-pressure in time AL AR- DE P-F A IL . Room thermostat stove is protected against A LAR - S IC - FAI L stove. You Tampering with the safety devices is prohibited.

  • Page 21: Problems And Solutions

    Problems and solutions All repairs must be carried out exclusively by a specialised technician, with the stove completely cold and the electric plug pulled out. Is prohibited from any unauthorized modification to the device and the replacement of parts with other non-original. The operations marked in bold type must be carried out by specialised personnel.
  • Page 22 before: 5. Contact an authorized service center place pipe plug plug if burned 11. Check the operation of the extractor flue 12. Contact an authorized service center tion stove 4. Replace the reduction motor 5. Replace the electronic board turn off 3.
  • Page 23 cleaning pellets If you repeat contact your es too long or clogged Authorized Service Center slot Contact your Authorized lets used Service Center Contact your Authorized Service Center Check and eventu- ally replace motor 1. Contact your Authorized Service Center 2.
  • Page 24 tive objects manufacturer. Sometimes, depending on the type, the stage of adjustment of the parameters need to vary the level relating to the loading of pellets o check the flow of fuel from technical authorized failure 11. Verify potential smoke duct is blocked and if the pressure switch is working properly 12.

Table of Contents