Table of Contents
Advertisement
One-touch Timer Recording
(OTR)
The One-touch Timer Recording feature provides a simple and
convenient way to make a timed recording.
One-touch Timer Recording (OTR)
Preparation:
•
Turn ON the TV and select to the corresponding
video input.
•
Press VCR DVD selector to select the VCR mode. (The
VCR mode indicator will light.)
Example: One-touch Timer Recording for 30 minutes.
1
Load a cassette tape with the erase prevention tab
intact.
•
The VCR will automatically turn on.
2
Press SP/SLP to select the desired tape speed SP
or SLP.
•
The tape counter and "SP" or "SLP" will appear
on the screen for about
3
Set "TV" or "CABLE" option to the appropriate
position
.
24
4
Press Direct channel selection buttons (0–9) or
CH +/– to select the channel to be recorded.
5
Press REC/OTR. Recording begins. Press the button
again to stop recording after 30 minutes. Each
additional press of REC/OTR will increase recording
time as shown in the chart below, up to a maximum
of 6 hours.
Press
Recording time
once
NORMAL REC
twice
0:30
3 times
1:00
4 times
1:30
5 times
2:00
•
The OTR and recording time will appear on the
screen for about 4 seconds, then change to "
To cancel OTR
Press STOP or turn off the power.
•
"
" will appear on the screen for about 4 seconds.
Note:
If you wish to watch the DVD playback during OTR or standard
recording, press VCR DVD selector to change to DVD mode
and perform the DVD playback
2K60121A.indb 29
2K60121A.indb 29
4 seconds.
Press
Recording time
6 times
3:00
7 times
4:00
8 times
5:00
9 times
6:00
10 times
NORMAL REC
".
.
32
Timer recording
Timer recording can be programmed on-screen with the
remote control. The built-in timer allows automatic unattended
recording of up to 8 programs within 1 month.
Timer recording
Preparation:
•
Press VCR DVD selector to select the VCR mode.
•
Load a cassette tape with the erase prevention tab
intact.
•
Check the time and date are correct
1
Press VCR MENU. Select "TIMER REC SET", then
press ENTER.
2
Press SET + or – to select one of the program line,
then press ENTER.
3
Press SET + or – to select the date, then press
ENTER.
4
Set the start time, end time, channel and tape speed
as in step 3.
Notes:
•
Press CANCEL to move cursor backward for correction.
•
To record from external source set the channel to "L1" or
"L2".
5
To enter other programs, repeat step 2 through 4.
•
To return to the normal screen, press VCR
MENU twice.
6
Press TIMER REC. The timer symbol (
appear on the display and the VCR standbys for
recording.
•
At the same time, VCR mode will change to DVD
mode automatically. You can use DVD even if the
VCR is in the timer recording mode. If you do not
use the DVD, turn the power off.
Notes:
•
The timer recording will start at 5 seconds before the
preset starting time.
•
If the timer symbol (
) does not appear on the display
when TIMER REC is pressed, the cassette is not inserted
.
25
•
If the cassette is ejected when TIMER REC is pressed,
the erase prevention tab of the cassette may have been
removed
.
25
Notes:
•
If the timer symbol (
) blinks when the timer recording
ended, the TV program has not been completely recorded
because of an insufficient tape length. Press TIMER REC
to cancel the timer program or press EJECT to remove the
cassette tape.
•
During timer recording standby mode, the VCR mode
cannot be operated. To use the VCR, first press TIMER
REC, then press VCR DVD selector to change to VCR
mode. After VCR mode is selected, press TIMER REC
again to put the VCR into timer recording standby mode.
•
If you press TIMER REC during timer recording, the
recording operation will be interrupted. If you press TIMER
REC again within the programmed time, the recording
operation will start again.
•
After a power failure or disconnection of the power plug, all
programmed recording settings and time display will be lost
upon resumption of power. In this case, reset the clock
and reprogram any timer recording.
.
23
) will
23
29
29
1/12/2007 3:50:12 PM
1/12/2007 3:50:12 PM
Hide quick links:
Advertisement
Table of Contents
