Table of Contents
Advertisement
EN 18
5.
LC9.3L LA
SDM
SDM
Figure 5-1 Service mode pad
After activating this mode, "SDM" will appear in the upper right
corner of the screen (when a picture is available).
How to Navigate
When the "MENU" (or HOME) button is pressed on the RC
transmitter, the TV set will toggle between the SDM and the
normal user menu.
How to Exit SDM
Use one of the following methods:
•
Switch the set to STAND-BY via the RC-transmitter.
•
Via a standard customer RC-transmitter: key in "00"-
sequence.
5.2.2
Service Alignment Mode (SAM)
Purpose
•
To perform (software) alignments.
•
To change option settings.
•
To easily identify the used software version.
•
To view operation hours.
•
To display (or clear) the error code buffer.
How to Activate SAM
Via a standard RC transmitter: Key in the code "062596"
directly followed by the "INFO" button. After activating SAM
with this method a service warning will appear on the screen,
continue by pressing the "OK" button on the RC.
Contents of SAM (see also
•
Hardware Info.
–
A. SW Version. Displays the software version of the
main software (example: LC93L-1.2.3.4=
AAAAB_X.Y.W.Z).
•
AAAA= the chassis name.
•
B= the region (A= Asian Pacific, E= Europe, L=
Latam, U= United States).
•
X.Y.W.Z= the software version, where X is the
main version number (different numbers are not
compatible with one another) and Y.W.Z is the sub
version number (a higher number is always
compatible with a lower number).
–
B. Standby Processor Version. Displays the
software version of the Stand-by processor.
–
C. Production Code. Displays the production code of
the TV, this is the serial number as printed on the back
of the TV set. Note that if an NVM is replaced or is
initialized after corruption, this production code has to
be re-written to NVM. ComPair will foresee in a
possibility to do this.
2010-Jul-01
Service Modes, Error Codes, and Fault Finding
18970_200_100325.eps
100325
Table
6-6)
•
Operation Hours. Displays the accumulated total of
operation hours (not the stand-by hours). Every time the
TV is switched "on/off", 0.5 hours is added to this number.
•
Errors (followed by maximum 10 errors). The most recent
error is displayed at the upper left (for an error explanation
see section
"5.4 Error
Codes").
•
Reset Error Buffer. When "cursor right" (or the "OK
button) is pressed and then the "OK" button is pressed, the
error buffer is reset.
•
Alignments. This will activate the "ALIGNMENTS" sub-
menu. See chapter
6.3 Software
•
Dealer Options. Extra features for the dealers.
•
Options. Extra features for Service. For more information
about option codes, refer to
if the option code numbers are changed, these have to be
confirmed with pressing the "OK" button before the options
are stored. Otherwise changes will be lost.
•
Initialize NVM. The moment the processor recognizes a
corrupted NVM, the "initialize NVM" line will be highlighted.
Now, two things can be done (dependent of the service
instructions at that moment):
–
Save the content of the NVM via ComPair for
development analysis, before initializing. This will give
the Service department an extra possibility for
diagnosis (e.g. when Development asks for this).
–
Initialize the NVM.
Note: When the NVM is corrupted, or replaced, there is a high
possibility that no picture appears because the display code is
not correct. So, before initializing the NVM via the SAM, a
picture is necessary and therefore the correct display option
has to be entered. To adapt this option bit, it is advised to use
ComPair (the correct values for the options can be found in
Table
6-5) or a method via a standard RC (described below).
Changing the display option via a standard RC: Key in the
code "062598" directly followed by the "MENU" (or HOME)
button and "XXX" (where XXX is the 3 digit decimal display
code as mentioned in
Table
6-5). Make sure to key in all three
digits, also the leading zero's. If the above action is successful,
the front LED will go out as an indication that the RC sequence
was correct. After the display option is changed in the NVM, the
TV will go to the Stand-by mode. If the NVM was corrupted or
empty before this action, it will be initialized first (loaded with
default values). This initializing can take up to 20 seconds.
Display Option
Code
39mm
PHILIPS
040
MODEL:
32PF9968/10
PROD.SERIAL NO:
AG 1A0620 000001
(CTN Sticker)
Figure 5-2 Location of Display Option Code sticker
•
Store - go right. All options and alignments are stored
when pressing "cursor right" (or the "OK" button) and then
the "OK"-button.
•
SW Maintenance.
–
SW Events. Not useful for Service purposes. In case
of specific software problems, the development
department can ask for this info.
–
HW Events. Not useful for Service purposes. In case
of specific software problems, the development
department can ask for this info.
Alignments.
6.4 Option
Settings. Note that
10000_038_090121.eps
090819
Hide quick links:
Advertisement
Table of Contents
