Beta 599 DGT-A/20 Instructions For Use Manual
Electronic torque wrench, direct torque and angle readout
Hide thumbs
Also See for 599 DGT-A/20:
- Instructions for use manual (104 pages) ,
- Instructions for use manual (112 pages)
Related Manuals for Beta 599 DGT-A/20
Summary of Contents for Beta 599 DGT-A/20
- Page 1 599DGT-A/20 ISTRUZIONI PER L’USO INSTRUCTIONS FOR USE MODE D’EMPLOI NL GEBRUIKSAANWIJZING GEBRAUCHSANWEISUNG INSTRUCCIONES INSTRUÇÕES DE USO INSTRUKCJA OBSLUGI HASZNÁLATI ÚTMUTATÓ...
- Page 2 INSTRUCTIONS BETA 599 DGT-A/20 Electronic torque wrench Direct torque and angle readout MAIN FEATURES – Digital driving torque and angle readout – +/- 2% and +/- 2° accuracy (90° rotation at a rate of 30°/sec) – CW and CCW operation –...
-
Page 3: Specifications
Drive Setting (mm) (N-m) (inches) Range (N-m) 599 DGT-A/20 40-200 1/2” 10-200 Beta 599 DGT-A/20 Accuracy CW: ±2% CCW: ±2% Operation Mode Peak Hold / Track “ ° “ Unit Selection N-m, ft-lb, in-lb, kg-cm Head Type Reversible ratchet Gear Teeth... - Page 4 – Usually press to reset the digital torque wrench before using it. ATTENTION: If an external force is applied to the torque wrench during the power-on/reset or wake up period, an initial torque offset will be found in the memory. IMPORTANT: When the wrench is used in the “angle”...
- Page 5 The wrench will start working again after a few seconds; however, it should be checked for Presetting Unit: Nm calibration at a Beta authorized centre as soon as possible. Press 2. The function “Unit Selection” is sequential...
- Page 6 The wrench will start working again after a few seconds; however, it should be checked for calibration at a Beta authorized centre as soon as possible. 2. If you apply torque over 5 N-m, the LCD display will start to display the torque value. If the applied torque is less than 5 N-m, the LCD display does not show any changes in value.
- Page 7 The wrench will start working again after a few seconds; however, it should be checked for calibration at a Beta authorized centre as soon as possible. 2. The green LED will be on for 90% of maximum setting torque.
- Page 8 VALUE STORAGE IN PEAK HOLD MODE *Note 1 Peak/track mode Keep pressed *Note 2 Peak/track mode selection Press Automatic change Storage n°. Storage value *Note 3 Press Delete stored value Press Note: (Quit) 1. The value storage system, “peak mode”, can be used for the “track (Delete) Deleted mode”...
- Page 9 ANGLE READOUT MODE OPERATON *Note 1 Angle mode Press *Note 2 *Note 3 Blinking Apply force and turn wrench Release Current torque Current angle * Nota 4 Over 80% of set value ((…((… …)) …)) 80% of set value reached *Note 5 Set value reached Release...
- Page 10 SELECTING TORQUE UNIT OF MEASUREMENT IN ANGLE MODE *Note 1 Angle mode Keep pressed Peak/track mode Press Selecting unit of measurement: N-m Press Selecting unit of measurement: in-lb Press Selecting unit of measurement: ft-lb Press Selecting unit of measurement: kg-cm Note: 1.
-
Page 11: Connecting Cable
CONNECTING CABLE Turn off the torque wrench and connect the cable to the PC and the wrench. DATA UPLOAD Ÿ Select the “Send” mode on the wrench. (See section “Value storage in peak hold mode”) Ÿ Insert the CD-ROM into the computer and start the data upload programme. Ÿ... -
Page 12: Battery Maintenance
10. Do not apply any force to the LCD panel. BATTERY MAINTENANCE 1. When the Beta 599 DGT-A/20 wrench is not used for an extended period of time, remove the battery. 2. Keep a spare battery on hand when going on a long trip or to cold areas.
Need help?
Do you have a question about the 599 DGT-A/20 and is the answer not in the manual?
Questions and answers