Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Bungard StenPrint 3000
Summary of Contents for Bungard StenPrint 3000
- Page 1 Stencil Printer StenPrint 3000...
-
Page 2: Table Of Contents
903.203 - Stencil holder frame ................................. 31 903.204 - Stencil clamp frame ................................. 31 903.205 - Stencil clamp for stencils in fixed frames ................................. 31 903.103 - Magnetic holders for double-sided printing ................................. 31 © 22.02.2017 Bungard GmbH & Co. KG... -
Page 3: Introduction
Instruction manual Introduction BUNGARD GmbH & Co. KG (called „BUNGARD“ in the following text) reserves the right to change or enhance its machines or machine specifications according to its judgment, if necessary. BUNGARD cannot be held responsible to implement aforesaid changes into machines sold already. -
Page 4: General
PCBs Only in the manual described utilization is allowed. The BUNGARD GmbH & Co. KG assumes no liability for damages made by not correct use of the machine. © 22.02.2017 Bungard GmbH & Co. KG... -
Page 5: Standard Text Symbols
Important The marked information should be read carefully to ensure a correct function of the machine Tips and Tricks This symbol marks useful information and helpful hints for the user. © 22.02.2017 Bungard GmbH & Co. KG... -
Page 6: Customer Service
Instruction manual Customer service There is a return to factory service available for BUNGARD SMD Pick & Place equipment. In the unlikely event of your machine needing to be repaired please send it to your supplier, area representative or direct to us. -
Page 7: Safety
Do not misuse the machine. Apply the machine only after its sense of use according to the manual. Repairing the devices is only permitted to service technicians of the BUNGARD GmbH & Co. KG. Consider if necessary also the special safety regulations of your country. -
Page 8: Safety And Maintenance
Please keep the work space clean. Contamination of the stencil printer could lead to premature wear. Examples: corrosion of metal parts or erosion of moving parts. Please check regularly the moving parts of free movement. If there is a rough-running you can use a lubricant. © 22.02.2017 Bungard GmbH & Co. KG... - Page 9 Should you have any problems with your stencil printer or need some advice on its use we shall be happy to be of assistance to you. The SD903.005 does not contain any parts requiring routine maintenance. © 22.02.2017 Bungard GmbH & Co. KG...
-
Page 10: System Components
The Y direction of the table can be adjusted by turning the two adjusting knobs 1b in the same direction. The Theta rotation can be set by turning the two adjusting knobs 1b in opposite directions. © 22.02.2017 Bungard GmbH & Co. KG... -
Page 11: Frame Fixture
The different frames available for fixing the stencils in place are listed under Optional accessories. Tips and tricks The frame fixture can be assembled in various positions where needed (see red arrows in the picture). Fr am e fixtur e © 22.02.2017 Bungard GmbH & Co. KG... -
Page 12: Tilt Mechanism
(5). By doing so, this enables the stencil printer to adapt to various stencil frames. With frames of varying weights, the tilt mechanism must be adjusted such that the stencil is positioned parallel to the PCB. Adjus ting the tilt m echanis m © 22.02.2017 Bungard GmbH & Co. KG... -
Page 13: Parallel Stencil Lift
Rotating the lever (4) a half turn in clockwise direction causes a lift of 2mm. Stencil lift bottom Stencil lift top The lever has a locking device at the top and bottom to enable repeated lifting. © 22.02.2017 Bungard GmbH & Co. KG... -
Page 14: Adjustable Pcb Thickness
® After that, the lever (4) can be clamped back in using the 3mm Allen key. Important Whilst the locking device of the lever (4) is being tightened, it must be pushed downwards. © 22.02.2017 Bungard GmbH & Co. KG... -
Page 15: Supporting Points
The supporting points comprise two knurled screws, the height of which can be set as required. As soon as the screws have been adjusted, they can be secured against moving by means of knurled nuts. Suppor ting points © 22.02.2017 Bungard GmbH & Co. KG... -
Page 16: Scraper
The stencil printer is supplied together with a scraper. The scraper is for applying the soldering paste to the stencil. Scr aper Tips and tricks There are various types of hand scrapers available to improve the printing process. © 22.02.2017 Bungard GmbH & Co. KG... -
Page 17: Optional Accessories
Depending on the size of the stencil, the parallel stencil lift cannot be used optimally. Attention No guarantee can be provided that all available “prototype stencils” can be held in place with the stencil holder frame.. © 22.02.2017 Bungard GmbH & Co. KG... -
Page 18: Assembling The Stencil
Now the clamping screws can be tightened again so that the stencil is firmly in place. o It is easier to tighten the clamping screws when the frame is turned over. Clam ping the s tencil The stencil holder frame can now be assembled into the stencil printer © 22.02.2017 Bungard GmbH & Co. KG... -
Page 19: Assembling The Stencil Holder Frame
Now the frame can be held in place with the corresponding knurled nuts (see red arrows in the picture). As s em bled s tencil holder fr am e © 22.02.2017 Bungard GmbH & Co. KG... -
Page 20: Stencil Clamp Frame
No guarantee can be provided that all available “prototype stencils” can be held in place with the stencil clamp frame. Important The magnetic holders are required to use the stencil clamp frame in the stencil printer for double-sided printing. © 22.02.2017 Bungard GmbH & Co. KG... -
Page 21: Mounting The Stencil
Now the clamping screws (see red arrows in the picture) of the first clamping jaw can ® be tightened with a 3mm Allen key. Ins er ting the s tencil © 22.02.2017 Bungard GmbH & Co. KG... - Page 22 By tightening up the knurled screws, the stencil is tensioned by way of the second clamping jaw (see yellow arrow in the picture) moving. The stencil holder frame can now be mounted into the stencil printer. Tens ioning the s tencil © 22.02.2017 Bungard GmbH & Co. KG...
-
Page 23: Mounting The Stencil Clamping Frame
Now the frame can be held in place with the corresponding knurled nuts (see red arrows in the picture). Mounted s tencil clam p fr am e © 22.02.2017 Bungard GmbH & Co. KG... -
Page 24: Stencil Clamping For Fixed Frames
The stencil clamping is fixed by two knurled screws (see pict. red arrows) at the printer. In addition the clamping is fixed by two cylinder screws (see green arrows) Stencil clam ping m ounted © 22.02.2017 Bungard GmbH & Co. KG... -
Page 25: Mounting The Frame
Instruction manual 4.7.1.3.2 Mounting the frame For mounting a fixed frame inclusive stencil it has to be inserted and fixed by the two knurled screws (see pict. red arrows). © 22.02.2017 Bungard GmbH & Co. KG... -
Page 26: Hand Scrapers
4.7.2 Hand scrapers There are two different sizes of scrapers available as optional accessories for the stencil printer. SD.0037.00 - hand s cr aper 110m m SD.0036.00 - hand s cr aper 255m m © 22.02.2017 Bungard GmbH & Co. KG... -
Page 27: Pcb Holders
With the magnetic holders, it is possible to hold PCBs that have already been assembled with components on the reverse of up to 18mm in height. 903.103 - m agnetic holder s for double-s ided pr inting © 22.02.2017 Bungard GmbH & Co. KG... - Page 28 PCB s uppor t PCB support with spigot The PCB supports with spigots are for supporting the PCB at its edge to be able to repeatedly hold it. PCB s uppor t w ith s pigot © 22.02.2017 Bungard GmbH & Co. KG...
-
Page 29: Accessories And Spare Parts
903.104 Magnetic-PCB-fixture set 903.105 double-sided printing Magnetic-PCB supporter set for Flexible vacuum-option for safe down-fixation of PCB while printing (903.206). 903.206 Incl. 4 magnetic suction cups and manual vacuum- deactivating. © 22.02.2017 Bungard GmbH & Co. KG... -
Page 30: Technical Data
Dimensions (B x T x H) ............350 x 45 x 90 mm Frame size max..............350 x 450 x 33 mm Weight ca................ca. 0,5 kg 903.103 - Magnetic holders for double-sided printing PCB underside ..............max. 18mm © 22.02.2017 Bungard GmbH & Co. KG... - Page 31 Bungard Elektronik GmbH & Co. KG · HRA 3980 Siegburg Bungard Verwaltungs GmbH · HRB 8043 Siegburg, Geschäftsführer Jürgen Bungard IBAN: (Int'l Bank Account) /DE 07 57391500 0031013801 BIC: SWIFT GENO DE 51 HAM Volksbank Rosbach BLZ 573 915 00 Kto. 31013801...
Need help?
Do you have a question about the StenPrint 3000 and is the answer not in the manual?
Questions and answers