Vents RTS-1-400 Instructions

If no button is pressed during 20 seconds, heat regulator will switch off.
Menu item 1: Accuracy of maintaining temperature. On the display, the text "Temp adjust" will appear. The default
value is 0; it is blinking in configuration menu. Any value from "-3" to "+3" may be selected. You may set on the
display the temperature of the premise of up to 3 degrees higher or lower than the set value.
Menu item 2: Entering upper limit of temperature setting. On the display, 37 0C is represented, that is default value
of upper limit, set by the manufacturer. Using "+" and "-" button, the upper limit may be set in the range from 26 0Ñ
to 37 0C.
Menu item 3: Entering lower limit of temperature setting. On the display, 5 0C is represented, that is default value of
lower limit, set by the manufacturer. Using "+" and "-" button, the lower limit may be set in the range from 5 0Ñ to
26 0C.
Menu item 4: Control of fan. On the display, "ON" is represented, that is default value, set by the manufacturer.
Using "+" and "-" button, "ON" or "OFF" may be selected. If "ON" is selected, heat regulator will switch the fan to
the set speed and will not stop it until mode selection button or fan speed selection button is pressed. When "OFF"
is selected, if, during heating, set temperature is lower than room temperature, or, during cooling, set temperature
is higher than room temperature, heat regulator will stop the fan and will stay in this mode until mode selection
button is pressed.
REMOTE CONTROL

REMOTE CONTROLLER

For control of operation of heat regulator with the help of remoter controller, point the remote controller to the front
panel of heat regulator from the distance of not more than 4 m.
In the course of long-term operation, discharge of power supply element is possible. In this case, replacement of
power supply element is required. To do this, pull out holder of the element from the bottom part of remote
controller and replace power supply element, observing polarity.

STORAGE RULES

It is necessary to store heat regulator in manufacturer's package in the ventilated premise at temperature from
0 0
+5 C to +40 C and relative air humidity of not more than 80 % (at T = 25 C).

MANUFACTURER'S WARRANTY

The manufacturer, "Vents" Joint-Stock Company, guarantees normal operation of heat regulator during 12 months
from the date of sale through retail trade network, in case of observance of transportation, storage, assembling and
operation rules. The warranty does not cover the goods with signs of mechanical damages.
If note about date of sale is absent, warranty period is started from the date of production. If any failures in
Operation Of Heat Regulator through manufacturer's fault are detected during the warranty period, the consumer has
a right to replace heat regulator at the manufacturer, according to Clause 14, Item 9 of the Law of Ukraine "About
Protection of Consumers".
Replacement is carried out by the address: 01030, Kiev, M.Kotsiubinsky Str. 1
ACCEPTANCE CERTIFICATE
Heat regulator of speed is accepted as ready for operation
Model Date of production
"Vents RTS-1-400"
"Vents RTSD-1-400"
(with the remote controller) Acceptance stamp
power night
mode
temperature
cooling heating
temperature
medium
high low
auto-control
holder of power
supply element
0
Sold
(name of trade enterprise, stamp of the shop)
Date of sale

DESTINATION

Heat regulator is intended for air heating or cooling with the help of control SPST or SPDT mixers with electrical
servo drive, control of 3-speed fan.

BASIC TECHNICAL SPECIFICATIONS

"up"
Power supply: 220 V AC, 50/60 Hz
Output capacity for contacts 2, 3, 4: not more than 2.0 A
"down"
Output capacity for contacts 5, 6: not more than 0.1 A
Temperature setting range: +5 C - +37 C
Overall dimensions: 86x86x15 mm
-Illuminated LC display
-Temperature setting is carried out simply by pressing buttons with "up" and "down" arrows
-On the display, setting temperature and temperature in the premise are displayed simultaneously
-Maintaining temperature to within 1 set degree
-Automatic switching of 3-speed gan
-Saving of user settings after switching off power supply
-Availability of remote controller (model RTSD-1-400)

DESCRIPTION OF DESIGN

Front panel (Fig.1)
Display 1
"power" button 2
mode selection button (HEATING, COOLING) 3
fan speed selection button (HIGH, MEDIUM, LOW, AUTO) 4
"night" mode selection button 5
increase of set value of temperature 6
decrease of set value of temperature 7
IR receiver 8 (for model RTSD-1-400)
Display (Fig.2)
shows that heat regulator is switched to "night" mode 9
shows that heat regulator is switched to cooling mode 10
shows temperature in the premise or set temperature 11
shows set temperature or temperature in the premise 12
shows whether valve with drive is switched or not 13
shows selection of fan speed 14
shows that heat regulator is working in heating mode 15

COMPLETE SET

The delivery set includes:

-heat regulator

1
-remote controller 1 (only for model RTSD-1-400)
-certificate
V21EN -02
(with remote controller)
0 0
1
8
Fig.1
15
14
13
Fig.2
HEAT REGULATOR
"VENTS RTS-1-400"
"VENTS RTSD-1-400"
2
3
4
5
6
7
9
MODE
10
AUTO
FAN
OFF
11
ROMM
12
SET
ON
OFF
1