Advertisement
Figure 5 Relay Wiring
TESTING AND RESETTING YOUR DETECTOR
A green power light indicates that power is supplied. To test the
detector (do not test when detector is at warm up mode), press the
test button and the detector will beep intermittently and the Yellow
Fault LED, Red Alarm LED will flash. Release the Test button, the
beep and the two LED will stop and green LED remains on.
A malfunctioning unit is indicated by beep-sounding twice within 4
Seconds and the Yellow Fault LED will flash. If this occurs, attempt
to disconnect the power supply to the unit for 10 seconds and then
power the unit again. Should the unit again beep intermittently, DO
NOT use this detector. Send the malfunctioning unit to the
manufacturer for servicing.
TAKING CARE OF YOUR DETECTOR
You have to maintain the detector frequently to ensure it working
properly. Few tips are provided for you to take care of your
detector:
(a) Use a vacuum cleaner to clean the air vents occasionally to
keep them free of dust. (Before cleaning your unit, unplug it
from the wall outlet or .)
(b) Push the Test button on your detector to test its operating
function once every week.
MEANINGS OF LED LIGHT & BUZZER
The LED light and buzzer turn on and/or off to indicate various
situations. There are four different light and buzzer operations:
(a) When the green LED is flashing, this situation means warm
up. This situation is occurs between detector just power on
and properly working.
(b) When the green LED remains on ， this situation means
detector is working properly.
(c) When the red LED flashes and the full alarm sounds
sequentially, this situation means alarm.
(d) When the unit emits beeps twice within 4 seconds and orange
LED flashes, it indicates that the unit is malfunctioning. In
this case, the detector is needed to be returned to
manufacturer for repair or service.
Note: The Red Alarm LED and Yellow Fault LED flash every 0.5s
and buzzer beeps as the sequence that 3 beeps, pause, 3 beeps
pause, when you press the Test button.
Figure 6 Control Unit
ACTIONS TO TAKE WHEN ALARM SOUNDING
In case of harmful levels of CO gas being detected, your detector
will go into a continuous full alarm. Try to take the following
necessary actions immediately:
(a) If there is anyone experiencing the effects of carbon monoxide
poisoning such as headache, dizziness, nausea or other
flu-like symptoms, call your fire department right away or 911.
You should evacuate all the people in the premises
immediately. Do a head count to check that everybody is
accounted for.
(b) Do not re-enter the premises until the problem has been
corrected and the CO gas has been dispersed out and a safe
level is reached.
(c) If no symptoms exist, Immediately ventilate the home by
opening windows and doors. Turn off fuel burning appliances
and call a qualified technician or your utility company to
inspect and repair your problem before restarting appliances.
WARNING: Normally an activation of the detector indicates the
presence of CO gas. However, the CO gas can be extremely fatal,
if it is not detected. The source of the CO gas may come from
several possible situations, please refer to the list of sources of
carbon monoxide in page 1.
CAUTION: This detector will only indicate the presence of CO gas
at the sensor. However, you have to be aware that the CO gas may
be present in other areas in the premises.
ACTIONS TO TAKE AFTER THE PROBLEM BEING
CORRECTED
Once the problem about the CO gas presence in the premises has
been corrected, the alarm of the detector should be off. After
waiting for 10 minutes, push the Test button to test the detector so
that you can make sure that the detector is working properly again.
TECHNICAL INFORMATION
Zeta CO 200 Carbon Monoxide Detector is engineered to be able
to provide alarm sounds based on the EN standards due to various
exposure time at different level of carbon monoxide concentrations.
Specifications:
MAINS POWERED
Input Supply Voltage:
Fuse Rating:
Power Consumption:
DC POWERED
Input Supply Voltage:
Fuse Rating:
Power Consumption:
ALL ALARMS
- 3 -
230V 50/60Hz.
0.2Amps in unswitched fused outlet.
less than 7 Watts.
9 to 28 Volts DC
0.5Amps.
less than 4 Watts.
Advertisement
