Download Print this page

CREE LIGHTING Cadiant Experience Dynamic Skylight Installation Instructions

Advertisement

Quick Links

IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be
followed including the following:
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
1.
DANGER- Risk of shock- Disconnect power before installation.
DANGER – Risque de choc – Couper l'alimentation avant l'installation.
2.
This luminaire must be installed in accordance with the NEC or your local
electrical code. If you are not familiar with these codes and requirements,
consult a qualified electrician.
Ce produit doit être installé conformément à NEC ou votre code électrique
local. Si vous n'êtes pas familier avec ces codes et ces exigences,
veuillez contacter un électricien qualifié.
3.
Access above ceiling required. Do not install insulation within 3 inches (76
mm) of any part of the luminaire. Suitable for suspended ceilings.
Acces requis au-dessus du plafond. Ne pas mettre l'isolant a moins de 76
mm (3 po) de toute partie du luminaire. Convient aux plafonds suspendus.
4.
Suitable for damp locations.
Convient aux emplacements humide.
5.
Do not use this equipment for other than its intended use
6.
Do not use outdoors
7.
Do not handle energized module with wet hands or when standing on wet or
damp surfaces, or in water.
SAVE THESE INSTRUCTIONS FOR
FUTURE REFERENCE
• The Cadiant™ Dynamic Skylight
is for non-insulated ceiling
applications using T-bar ceiling
grid or in drywall applications only
when mounted on Cree Drywall
Grid Adapter DGA-22.
TO INSTALL:
1
CORRECT HANDLING
Handle the Cadiant™
Dynamic Skylight Here
1 of 3
• Designed for use in
120-277VAC protected circuits
(fuse box, circuit breaker). Supply
wire sized in accordance with
national and local electrical wiring
codes rated 90C or higher
IMPROPER HANDLING-
Do NOT Handle Interior
Sidewalls
IMPORTANT NOTES:
• Do not screw any
additional screws into
the side or top of the
luminaire.
• Do not put pressure
on or hold by the
interior sidewalls.
This may damage the
optic. See Figure 1.
SIDEWALLS
Cadiant
Experience
Dynamic Skylight
Includes: Cadiant™ Luminaires
INSTALLATION INSTRUCTIONS
INSTRUCTIONS D'INSTALLATION
• Do not push on top of
the center lens. See
Figure 1.
• Do not lay the
luminaire on the
sensor on the front
face. See Figure 2.
IMPROPER HANDLING-
CENTER LENS
Do NOT Touch
Center Lens
LPN00647X0001A0_D

Advertisement

loading
Need help?

Need help?

Do you have a question about the Cadiant Experience Dynamic Skylight and is the answer not in the manual?

Questions and answers

Summary of Contents for CREE LIGHTING Cadiant Experience Dynamic Skylight

  • Page 1 Cadiant Experience ™ Dynamic Skylight Includes: Cadiant™ Luminaires IMPORTANT SAFEGUARDS INSTALLATION INSTRUCTIONS INSTRUCTIONS D’INSTALLATION When using electrical equipment, basic safety precautions should always be followed including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS DANGER- Risk of shock- Disconnect power before installation. DANGER –...
  • Page 2 Wiring Access Panel RFM Module Module Compartment (4) Tabs For Safety Wire Hangers Do not screw any additional screws into the side or top of the luminaire. (4) Tabs For Safety Wire Hangers (4) T-Bar Retention Clips Sensor NEEDS TO BE ORIENTED NORTH WEST EAST`...
  • Page 3 Connect the luminaire green or green/yellow ground lead to the green supply lead. © 2019 Cree Lighting, A company of IDEAL INDUSTRIES. All rights reserved. For informational purposes only. Content is subject to change. See http://creelighting.com/warranty for warranty and specifications. Cadiant is a trademark of Cree ™...