Download  Print this page

Craftsman 48181 Operator's Manual

3 piece floor jack set.
Hide thumbs

Advertisement

Operator's Manual
3 Piece Floor Jack Set
Model 48181
CUSTOMER HELP LINE
8:00 AM - 4:45 PM Central Time
此处贴标
15.24CM
X
10.16CM
Jack Stands
WARNING: Before using this product,
read this Operator's Manual and follow
all its Safety Rules and Operating
Instructions.
Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A.
www.craftsman.com
ASME PASE 2014 Compliant
Parts and Questions
1-888-332-6419
Monday- Friday
Creeper
Floor Jack
• Safety
• Operation
• Maintenance
Printed in China

Advertisement

Table of Contents

   Related Manuals for Craftsman 48181

   Summary of Contents for Craftsman 48181

  • Page 1 Operator’s Manual 3 Piece Floor Jack Set Model 48181 CUSTOMER HELP LINE Parts and Questions 1-888-332-6419 8:00 AM - 4:45 PM Central Time 此处贴标 Monday- Friday 15.24CM 10.16CM Creeper Floor Jack Jack Stands WARNING: Before using this product, • Safety read this Operator’s Manual and follow...
  • Page 2 Jack AIR PURGE PROCEDURE IMPORTANT: BEFORE FIRST USE, perform the following Air Purge Procedure to remove any air that may have been introduced into the hydraulic system as a result of product shipment and handling. Purge Air Insert Handle With a flat blade screwdriver, See “...
  • Page 3 CRAFTSMAN LIMITED WARRANTY SAFETY INSTRUCTIONS Read Operating Instructions CRAFTSMAN LIMITED WARRANTY Study, understand and follow all instructions in FOR ONE YEAR from the date of sale this this manual before operating the jack. Failure product is warranty against defects in material to heed these warnings may result in loss of or workmanship.
  • Page 4 ASSEMBLY Assembly Handle Assembly • Refer to Picture 1 when performing this step. Align Quick Disconnect pushpin in upper handle piece with attachment hole in lower handle piece. Push upper piece into lower piece until pushpin pops through hole. • Sufficiently loosen the Handle Socket Screw to insert the assembled handle (Picture 2).
  • Page 5 • Continue to pump jack handle to lift vehicle to Rust Prevention: desired height. • Check ram and pump plunger on the Power • After lifting, support the load with Unit Assembly every two months (or sooner, appropriately rated vehicle support stands based on usage) for any signs of rust or before working on vehicle.
  • Page 6 EXPLODED VIEW AND PARTS LIST Oil Fill Screw Description Qty. Saddle Lift Arm Side Plate Assembly Front Wheel Rear Caster Assembly Handle Handle Socket Power Unit Assembly TROUBLESHOOTING Symptom Poor jack Handle Jack will Jack will Jack will Jack will lifting, raises by not lift...
  • Page 7 Jack Stands CRAFTSMAN LIMITED WARRANTY CRAFTSMAN LIMITED WARRANTY SAFETY INSTRUCTIONS FOR ONE YEAR from the date of sale this Read Operating Instructions product is warranty against defects in material Study, understand and follow all instructions in or workmanship. WITH PROOF OF SALE this manual before operating the jack stands.
  • Page 8 Replacement stands must be facility. Annual inspection of the stand is purchased as a matched pair. recommended by a Craftsman repair facility Store stands in upright position and in a to ensure that the stand is in optimum clean, dry area.
  • Page 9 This creeper was designed for use on hard level surfaces capable of sustaining the load. CRAFTSMAN LIMITED WARRANTY CRAFTSMAN LIMITED WARRANTY FOR ONE YEAR from the date of sale this product is warranty against defects in material or workmanship.
  • Page 10 MAINTENANCE Maintenance • Periodically inspect for corrosion, damage, cracking, bent or missing parts. Stop using the creeper immediately If any of these conditions are found. Rectify before using. • Do not expose to prolonged wet or corrosive conditions. • Clean all surfaces after each use with a dry clean cloth only.
  • Page 11 NOTE...
  • Page 12 For Help Line, Parts and Service: Call 8:00 am - 4:45 pm, CT, Monday - Friday 1-888-332-6419 Para la linea de ayuda, partes y servicio: Llame de 8:00 am - 4:45 pm, CT, Lunes-Viernes 1-888-332-6419...

Comments to this Manuals

Symbols: 0
Latest comments: