Related Manuals for Minuteman MC20004CE
Summary of Contents for Minuteman MC20004CE
- Page 1 Model: MC20003QP 200X MC20004CE Brush Drive Floor Scrubber Electric OPERATION SERVICE PARTS CARE Revised 6/02...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Page Safety Instructions Electrical Requirements Control Panel Identification Operating Instructions Squeegee Adjustments Brush Installation/Removal Base Assembly 7 & 8 Tank Assembly 9 & 10 Upper Assembly Console Assembly Motor Lift Assembly Scrubhead Assembly Back Panel Assembly Squeegee Lift & Mechanism Assembly Squeegee Assembly Complete Wiring Diagram, 115V Wiring Diagram, 230V CE... -
Page 4: Safety Instructions
FOR COMMERCIAL USE ONLY IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING WARNING - To reduce the risk of fire, electric shock, or injury: • Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing, cleaning or maintaining. -
Page 5: Electrical Requirements
120 volt, 60 hz, AC circuit. Voltages below 105 volt AC or above 125 volts AC could cause serious damage to the motor. (Model MC20004CE) This machine is designed to operate on a standard 16 amp. type L fused 230 volt, 50 hz, AC circuit. Voltages below 200 volt AC or above 250 volts AC could cause serious damage to the motor I.E. -
Page 6: Control Panel Identification
1. Squeegee lift lever 2. Recovery dump hose 3. Dashboard control panel 4. Solution control lever 5. Solution dump hose 6. Quick disconnect Aux. out (optional) 7. Food pedal 8. Receptacle 9. Circuit breaker 10. Main power 11. Brush switch 12. -
Page 7: Operating Instructions
OPERATING INSTRUCTIONS BEFORE STATING, FAMILIARIZE YOURSELF WITHTHE MACHINE AND ITS CONTROLS (SEE “MACHINE OVERVIEW” & CONTROL PANEL DIAGRAMS) 1. Filling: Fill the solution tank with the desired amount of water and add liquid cleaning solution to the proper dilution ratio. DO NOT USE powdered cleaning chemicals. -
Page 8: Squeegee Adjustments
SQUEEGEE ADJUSTMENTS Squeegee Adjustment The squeegee set-up is pre-adjusted at the factory. Adjustments may be required to get optimum performance for different floors and conditions. Pitch Control Adjustment 1. Ensure that the scrubber is on a relatively flat surface. Pull the red emergency button away from the dashboard to activate power. -
Page 9: Brush Installation/Removal
BRUSH INSTALLATION - REMOVAL INSTALLATION 1. Raise the scrubhead to the “UP” position by depressing the pedal (A) downward as shown on Fig. 1. 2. Center brush (D) under the scrubhead shroud while lining up the center hex drive hub and pressing the brush up until the brush engages on the drive hub. REMOVAL 1. -
Page 10: Base Assembly
BASE ASSEMBLY... - Page 11 BASE ASSEMBLY Parts List Item Part No. Qty. Description 200102 Base 200250 Axle Weldment 712301 WSR-Flat .38 x .88 x .06 762332 Wheel, 8 x 2 w/Bearing 711375 Nut-Nyloc 3/8-16 711578 WSR-Flat ½ Brass 712318 WSR-Flat ¾ x 1.12 x .12 712759 WSR-Flat 5/16 x 1.37 x .06 SS 712042...
-
Page 12: Tank Assembly
TANK ASSEMBLY... - Page 13 TANK ASSEMBLY Parts List Item Part No. Qty. Description 200101 Solution/Recovery Tank 200147 Bracket, Vac Motor 200173 Float, Housing 210122 Drain Hose Wirelock 200232 Cable, Tank 200251 Stand Pipe Assembly 200258 Muffler Assembly 200270 Hose, ¾ Solution Drain 200023 Garden Hose Cap 210409 Fitting, Brass 3/8 MPT 210410...
-
Page 14: Upper Assembly
UPPER ASSEMBLY Parts List Item Part No. Qty. Description 200160 Tank Assembly 200178 Gasket, Lid 200136 Gasket, Solution Lid 200103 Tank Lid 712120 Shoulder Bolt ½ x 2 710178 SCR-MC ¼-20 x ½ 711503 WSR-Flat #10 711125 SCR-ST-B #10 x ½ 760286 Wire Formed Hook 200176... -
Page 15: Console Assembly
CONSOLE ASSEMBLY Parts List for 200330 Item Part No. Qty. Description 200104 Console 200134 Console Bracket Right 200135 Console Bracket Left 200151 Hinge Bracket Weldment 200322SP Dashboard ASM BD 712320 WSR-Nylon .22 x .45 x .04 712540 SCR-MC #10-24 x .37 SS 711575 WSR-Flat .31 x .75 x.06 711545... -
Page 16: Motor Lift Assembly
MOTOR LIFT ASSEMBLY Parts List Item Part No. Qty. Description 200120 Base Plate Weldment 260036 712310 WSR-Flat .52 x .88 x .06 711527 WSR-Flat 5/8 x 1.12 x .12 762340 Oilite Bushing ½ 260041 Oilite Flanged Bushing ½ 200115 Lift Arm Weldment 711713 E-Ring ½... -
Page 17: Scrubhead Assembly
SCRUBHEAD ASSEMBLY Parts List Item Part No. Qty. Description 200109 Motor Platform Weldment - BD 200187 Brush Shroud Weldment 200194 Pin, Brush Release 200294 Shroud Strap 210066 Retainer Bolt 200293 Shroud Skirt 260183 Nut ¼ NPT Nylon 320268 Key, ¼ x 5/16 x 1.00 430035 Drive Hub 500033... -
Page 18: Back Panel Assembly
BACK PANEL Parts List Item Part No. Qty. Description 742307 Switch, McGill, VDE 200229 Bracket, Kill Switch 710307 SCR-MC 6-32 x 1 200326 Cover Switch Box 711125 SCR-ST #10 x .5 711316 Nut-Hex ¼-20 711544 WSR-Helical ¼ 711430 Nut-Tinnerman 6-32 200332 Wire Guard Cover 200311... -
Page 21: Wiring Diagram, 115V
WIRING DIAGRAM, 115V... -
Page 22: Wiring Diagram, 230V Ce
WIRING DIAGRAM, 240V CE... - Page 23 Minuteman International, Inc. warrants to the original purchaser/user that this product is free from defects in workmanship and materials under normal use and service for a period of three years from date of purchase. In addition, Minuteman International, Inc. will, at its option, honor labor warranty claims for the first 12 months from date of sale, provided such claims are submitted through and approved by factory authorized repair stations.