Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Minuteman M2400
Summary of Contents for Minuteman M2400
- Page 1 Parts and Instruction Manual M2400 Electric Burnisher W/ Dust Control Option...
- Page 2 This manual is furnished with each new MINUTEMAN M2400. This provides the necessary operating and preventive maintenance instructions. Operators must read and understand this manual before operat- ing or servicing this machine. This machine was designed to give you excellent performance and efficiency. For best results and minimal cost, please follow the general guidelines below: ·...
- Page 3 Parts and Instruction Manual...
-
Page 4: Table Of Contents
Base Assembly BOM ........................9 Handle Assembly .......................... 10 Handle Assembly BOM ......................... 11 Dust Control Option ........................12 Dust Control Option BOM ......................13 Wiring Diagrams ..........................14 Minuteman International Made Simple Commercial Limited Warranty ........16 Parts and Instruction Manual... -
Page 5: Important Safety Instructions
FOR COMMERCIAL USE ONLY IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING WARNING - To reduce the risk of fire, electric shock, or injury: • Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing. -
Page 6: Inspection
INSPECTION Carefully unpack and inspect your machine for shipping damage. Each unit is tested and thoroughly inspected before shipment, and any damage is the responsibility of the delivery carrier who should be notified immediately. WARNING • Read Instruction Manual before operating this piece of equipment. •... - Page 7 POUR USAGE COMMERCIAL SEULEMENT MODE D’EMPLOI SECURITAIRE Lorsque l’on utilise un appareil électrique, des précautions de base doivent toujours être suivies telles que: BIEN LIRE LE MODES D’EMPLOI AVANT USAGE AVERTISSEMENT Pour réduire les risques de feu, choc électrique ou blessure: •...
- Page 8 INSPECTION Déballer soigneusement en constatant s’il y, a lieu tout dommage apparent. Chacune des pièces d’équipement est entièrement inspectée à l’usine et tout dommage de transit est la responsabilité de la compagnie de transport qui devrait être prévenue immediatement. AVERTISSEMENT •...
-
Page 9: Model 2400 Burnisher Operating Instructions
Model 2400 Burnisher Operating Instructions 1. Install the polishing pad on to the pad driver. Make sure your installing a true 20” polishing type pad. Then install the locking centering device cup by lining up the threads on the pad driver and the cup and push straight down, or just screw the cup devise onto the pad driver. - Page 10 Model 2400 Burnisher Operating Instructions 4. After the machine has started the pad pressure gauge, located at the backside near the rear of the base, should be reading at the top of the white zone, or telling the operator the pad is off the floor. Now, to increase the pad pressure keep the burnisher running with one hand and pushing the machine in a back and forth motion.
-
Page 11: Preventive Maintenance
Model 2400 Burnisher Operating Instructions Preventive Maintenance 1. Inspect motor carbon brushes approximately every 250 hours. A set of carbon brushes should last as long as 2500 hours. Premature wear may indicate other problems with the motor. These can be inspected by removing the motor cover. Indications for changing carbon brushes would be if the indicator light comes on or if the carbon brushes are flush with or slightly recessed in the brass brush holder. -
Page 12: Exploded Views
Exploded Views Base Assembly Parts and Instruction Manual Page 8... -
Page 13: Base Assembly Bom
Base Assembly BOM Item Part No. Qty. Description Item Part No. Qty. Description 740044 Cap-Wire 12-18 74B 130040PTD Handle PTD DK Grey 740220 Circuit Breaker 20AMP 2-Terminal 115V 130040CTD Handle - Coated 740106 Circuit Breaker 9AMP Push Button 150208 Motor Bracket 56/56 Frame 240V 150209 Foam Tape 25 in. -
Page 14: Handle Assembly
Handle Assembly Parts and Instruction Manual Page 10... -
Page 15: Handle Assembly Bom
Handle Assembly BOM Item Part No. Qty. Description 150002 Cord-14GA-3 50FT Med Grey 740600 Cord-European F3 G1.5MM 50Ft B 150003 Strain Relief 100x50 150004 Strain Relief Heyco 3251 170040PLT Cord Hook Plated 190006 End Cap 190008 Switch Cap 190009B Safety Button Black 190010 Strain Relief 190015... -
Page 16: Dust Control Option
Dust Control Option Parts and Instruction Manual Page 12... -
Page 17: Dust Control Option Bom
Dust Control Option BOM Item Part No. Qty. Description 230034 Dust Tube 230101 Hose 2” C/L 14” 380035 Gasket 4.31 x 5.81 x .19 390061 O-Ring - Valve Stem 710197 SCR-SC 5/16-18 x .75 710556 SCR-MC 10-32 x .75 Zinc 711202 BLT-HH 1/4-20 x .50 STL Zinc 711350... -
Page 18: Wiring Diagrams
Wiring Diagrams Parts and Instruction Manual Page 14... - Page 19 Parts and Instruction Manual Page 15...
-
Page 20: Minuteman International Made Simple Commercial Limited Warranty
A potential health hazard exits without original equipment replacement. All warranted items become the sole property of Minuteman or its original manufacturer, whichever the case may be. Minuteman disclaims any implied warranty, including the warranty of merchantability and the warranty of fitness for a particular purpose.