Instructions For The User; Using The Burners - Bompani BO 213 MB/N Instructions For The Installation And Use

INSTRUCTIONS FOR THE USER

It is necessary that all the operations regarding the installation, adjustment and
adaptation to the type of gas available are carried out by qualified personnel, in
conformity with the regulations in force.
The specific instructions are described in the booklet section intended for the
installer.

USING THE BURNERS

The symbols silk-screen printed on the side of the knob
indicate the correspondence between the knob and the
burner.
Start-up without valves
Turn the corresponding knob anticlockwise up to the
maximum position (large flame, fig. 1) and press.
Automatic start-up with valves
Turn the corresponding knob anticlockwise up to the
maximum position (large flame, fig. 1) and press the knob.
Once the burner has been started up, keep the knob
pressed for about 6 seconds.
Using the burners
In order to obtain the maximum yield without waste of
gas, it is important that the diameter of the pot is suitable
for the burner potential (see the following table), so as to
avoid that the flame goes out of the pot bottom (fig. 2).
Use the maximum capacity to quickly make the liquids
reach the boiling temperature, and the reduced capacity to
heat food or maintain boiling. All of the operating positions
must be chosen between the maximum and the minimum
ones, never between the minimum position and the closing
point.
Use the maximum capacity to quickly make the liquids
reach the boiling temperature, and the reduced capacity to
heat food or maintain boiling. All of the operating positions
must be chosen between the maximum and the minimum
ones, never between the minimum position and the closing
point.
The gas supply can be interrupted by turning the knob
clockwise up to the closing position.
If there is no power supply, it is possible to light the
burners with matches, setting the knob to the start-up
point (large flame, fig. 1).
BURNERS POWER W
Auxiliary
Semi-rapid
Rapid
Triple crown
Notice
- When the equipment is not working, always check that
the knobs are in the closing position (see fig.1).
- If the flame should blow out accidentally, the safety
valve will automatically stop the gas supply, after a few
Ø of pots
1000 10 - 14 cm
1750 16 - 18 cm
3000 20 - 22 cm
3800 24 - 26 cm
seconds. To restore operation, set the knob to the lighting
point (large flame, fig. 1) and press.
- While cooking with fat or oil, pay the utmost attention as
these substances can catch fire when overheated.
- Do not use sprays near the appliance in operation.
- Do not place unstable or deformed pots on the burner, so
as to prevent them from overturning or overflowing.
- Make sure that pot handles are placed properly.
- When the burner is started up, check that the flameis
regular and, before taking pots away, always lowerthe
flame or put it out.
CLEANING
Before any operation, disconnect the appliance from the
electric grid.
It is advisable to clean the appliance when it is cold.
Enamelled parts
The enamelled parts must be washed with a sponge and
soapy water or with a light detergent.
Do not use abrasive or corrosive products.
Do not leave substances, such as lemon or tomato juice,
salt water, vinegar, coffee and milk on the enamelled
surfaces for a long time.
Stainless steel parts
Stainless steel can be stained if it remains in contact with
highly calcareous water or aggressive detergents for an
extended period of time.
The stainless steel parts should also be cleaned with
soapy water and then dried with a soft cloth.
Burners and racks
These parts can be removed to make cleaning easier.
The burners must be washed with a sponge and soapy
water or with a light detergent, wiped well and placed in
their housing perfectly. Make sure that the flame-dividing
ducts are not clogged.
Check that the feeler of the safety valve and the start-up
electrode are always perfectly cleaned, so as to ensure an
optimum operation.
The racks can be washed in the dishwasher.
Gas taps
The possible lubrication of the taps must be carried out by
specialized personnel, exclusively.
In case of hardening or malfunctions in the gas taps,
apply to the Customer Service.
3