Related Manuals for Peregrine Semiconductor Corporation PE9601
Summary of Contents for Peregrine Semiconductor Corporation PE9601
- Page 1 PE9601 EVALUATION KIT USER’S MANUAL 6175 Nancy Ridge Drive, San Diego, CA 92121 (858) 455-0660, Fax (858) 455-0770 http://www.peregrine-semi.com Peregrine Semiconductor Corporation® Doc. 79/0001~02A...
-
Page 2: Table Of Contents
Table of Contents Introduction Introduction..................5 Applications Support ...............5 FCC Labeling Requirement .............5 Hardware Installation Evaluation Kit Contents And Requirements........7 Evaluation Kit Configuration............8 Evaluation Kit Setup ................8 Software Section Software Setup for Serial Mode Programming ......14 Peregrine Semiconductor Corporation ® Doc. 79/0001~02A... - Page 3 Semiconductor Corp. Peregrine Semiconductor Corp., the Peregrine logotype, and UTSi are registered trademarks of Peregrine Semiconductor Corp. PE9601 is a trademark of Peregrine Semiconductor Corp. Peregrine Semiconductor Corp. reserves the right to make improvments to the hardware, firmware or soft- ware described in this manual at any time and without notice.
- Page 4 Introduction Peregrine Semiconductor Corporation® 4 Doc. 79/0001~02A...
-
Page 5: Introduction
Introduction This Evaluation Kit is specifically designed for evaluating the PE9601 2.2 GHz Integer-N PLL. The Evaluation Kit allows maximum flexibilty for optimizing phase noise, spur, lock time and power performance for specific applications. Using the hardware and software provided in the Evaluation Kit, both serial and direct modes of programming can be demonstrated. - Page 6 Hardware Section Peregrine Semiconductor Corporation® 6 Doc. 79/0001~02A...
-
Page 7: Evaluation Kit Contents And Requirements
Evaluation Kit Contents And Requirements The Evaluation Kit includes all of the specific software and hardware required to evaluate the PE9601. Included in the Evaluation Kit are: 1 PE9601 Evaluation Board 1 PE9601 2.2 GHz Integer-N PLL 1 CD with Application Software included... -
Page 8: Evaluation Kit Configuration
10 MHz on-board reference or an external reference. Setting the BMODE Control switch (BMODE switch S3-1) to the "on" position enables direct mode programming. In the direct mode, the PE9601 can be programmed using the fifteen on-board switches. Setting the BMODE Con- trol switch (BMODE switch S3-1) to the "off"... - Page 9 Instructions for programming PLL registers are available in the datasheet. 6. To perform the evaluation of the PE9601 using the computer’s printer port, connect the 8-wire interface cable (3-wire serial interface and GND) between the computer’s printer port and J1 on the Evaluation Board.
- Page 10 S1 Switch 1 On (Enhanced Mode Off) REF In PLL +3V Supply [J7, Pins 1(+) & 3(-)] VCO +5V Supply [J7, Pins 31(+) & 33(-)] S3 Switch 8 On VCO Out (J5) (Serial Programming) Peregrine Semiconductor Corporation ® 10 Doc. 79/0001~02A...
- Page 11 Figure 2. Jumper Setting to Disable On-board Reference. JP1 - Jumper on left two pins J3 Removed REF In Peregrine Semiconductor Corporation ® 11 Doc. 79/0001~02A...
- Page 12 8-Wire Serial Interface to J7, Pins 1 & 3 +3V Supply Computer PLL VDD Printer Port PE3236 J7, Pins 31 & 33 +5V Supply VCO VDD Spectrum Analyzer J5 - VCO Output to Peregrine Semiconductor Corporation ® 12 Doc. 79/0001~02A...
-
Page 13: Software Section
Software Section Peregrine Semiconductor Corporation ® 13 Doc. 79/0001~02A... -
Page 14: Software Setup For Serial Mode Programming
Software Setup for Serial Mode Programming 1) When programming the PE9601 in serial mode using the computer printer port option, the following software programming features are not available: •Enhancement modes are not available •Ping-pong mode is not available •Parallel and Direct interface modes are not available (Note: The direct... - Page 15 Figure 4: PE3236 Software Control Panel Note: Although the "PE9600" symbol appears on the above screen, this software is applica- ble to the PE9601. Peregrine Semiconductor Corporation ® 15 Doc. 79/0001~02A...