Whirlpool Cabrio W10026634B Manual page 2

FOR SERVICE TECHNICIAN ONLY – DO NOT REMOVE OR DESTROY
something is faulty with the button, and it is not
possible to enter the diagnostic mode.
If no indicators come on after pressing POWER
button, go to TEST #1, page 4.
Indication 2: Fault code flashes from the
display.
Action:
Review the Display Fault/Error Codes table,
page 3, for the recommended procedure.
DIAGNOSTIC: Saved Fault Codes
The machine will save up to 4 of the most recent
fault codes. Fault codes will not be saved or displayed
in any order. If there are saved fault codes (as indicated
in step 3 of Activation of Automatic Diagnostic Test
Mode, page 1), a saved fault code will be displayed and
alternately show "F" and "XX" where XX is the fault code,
and all the cycle selector indicators flash.
Press and release
the same button
The next saved fault code
used to activate is displayed.
Diagnostics
The next saved fault code
Repeat
is displayed.
The final saved fault code
Repeat
is displayed.
All indicators momentarily turn
Repeat off, then stay on. After 5 seconds,
Automatic test cycle begins.
NOTE: Fault codes are retained, after displaying them
and/or interrupting power.
ACTIVATION OF MANUAL DIAGNOSTIC
TEST MODE
1. Read and perform steps 1 and 2 under
Activation of Automatic Diagnostic Test Mode,
page 1, and press the same button once during the
88
5 second display time of the .
NOTE: If the button is not pressed within 5 seconds,
the Automatic test will start (after saved fault codes).
2. If done successfully, a single beep occurs and the
two-digit display shows the User Interface ID# (
09
, etc.) for 3 seconds, then displays
Add A Garment indicator LED flashes. See
Diagnostic: Manual, below.
DIAGNOSTIC: Manual
Enter Manual Diagnostic test mode, above. Two-digit
00
display shows , and Add A Garment indicator LED
is flashing.
NOTE: If there is no activity (button press, cycle select)
within 5 minutes, the control automatically exits
Diagnostic mode and enters standby mode.
Manual: Water Valves
(See Manual Activation,
above)
To check FRESH valve
select or press the following:
WHITEST WHITES START (turns on Fresh valve,
cycle indicator flashes) WASH TEMP/RINSE TEMP
(enables fill of Hot, Warm, Cold, or no water according
to WASH TEMP/RINSE TEMP selection and indicator)
START (turns off Fresh valve, cycle indicator is
steady on).
To check DETERGENT valve
select or press the
following:
HEAVY DUTY START (turns on Detergent valve,
cycle indicator flashes) WASH TEMP/RINSE TEMP
(enables fill of Hot, Warm, Cold, or no water according
to WASH TEMP/RINSE TEMP selection and indicator)
START (turns off Detergent valve, cycle indicator
is steady on).
P A R T N O . W 1 0 0 2 6 6 3 4 B
To check FABRIC SOFTENER valve
the following:
NORMAL START (turns on Fabric Softener valve,
cycle indicator flashes) WASH TEMP/RINSE TEMP
(enables fill of Hot, Warm, Cold, or no water according
to WASH TEMP/RINSE TEMP selection and indicator)
START (turns off Fabric Softener valve, cycle
indicator is steady on).
To check BLEACH valve
CASUAL START (turns on Bleach valve, cycle
indicator flashes) WASH TEMP/RINSE TEMP (enables
fill of Hot, Warm, Cold, or no water according to WASH
TEMP/RINSE TEMP selection and indicator)
(turns off Bleach valve, cycle indicator is steady on).
NOTE: Models with Bleach valve located in alternate
position, as shown in Figure 4, can only fill cold through
bleach valve; for these models, it is only necessary to Select
CASUAL and press START for water to start flowing through
the bleach dispenser.
If any valve fails to turn on go to TEST #2, page 4.
Manual: Pumps
Models with Push-button cycles:
Press and release:
CLEAN WASHER
(Impeller) or DRAIN &
SPIN (Agitator)
Repeat
Repeat
Repeat
Models using Cycle Selector:
Select CLEAN WASHER or DRAIN & SPIN.
Press and release:
START
Repeat
Repeat
08
,
Repeat
00
and the
If pumps fail to turn on, go to TEST #7, page 6.
Manual: Lid Switch
at left)
Opening the lid should cause the Clothes Clean or Done
status indicator to turn off. Closing the lid should cause
the indicator to turn on.
If Clothes Clean or Done indicator does not turn
off or on, go to TEST #8, page 6.
Manual: Lid Lock
NOTE: Lid must be closed. If lid is not closed, an invalid
button press beep will occur when performing next step.
Press and release:
2nd RINSE or
EXTRA RINSE
Repeat
If lid does not lock or unlock, go to TEST #8,
page 6.
Manual: Motor
Rotor Position Sensor (RPS):
and Spin indicators to detect the three hall sensors.
Console may have up to two of these indicators on
at one time when the basket is not moving. Open lid
and rotate basket by hand. The Wash, Rinse and Spin
status indicators should toggle on and off according
to direction the basket is being turned.
POUR LE TECHNICIEN SEULEMENT – NE PAS ENLEVER NI DÉTRUIRE
select or press
select or press the following:
START
(See Manual Activation, at left)
Turns on recirculation pump,
button indicator is steady on.
Turns off recirculation pump,
button indicator turns off.
Turns on drain pump, button
indicator flashes.
Turns off drain pump, button
indicator turns off.
Turns on recirculation pump,
cycle indicator is steady on.
Turns off recirculation pump,
cycle indicator is off.
Turns on drain pump, cycle
indicator flashes.
Turns off drain pump, cycle
indicator is off.
(See Manual Activation,
(See Manual Activation, at left)
Lid locks, Lid Lock indicator
turns on.
Lid unlocks, Lid Lock
indicator turns off.
(See Manual Activation, at left)
Uses Wash, Rinse
P A G E 2
If none of these indicators are on go to TEST #3,
page 4.
Spin:
To activate Spin, lid must be closed with lid lock
enabled. See Manual: Lid Lock test, at left.
NOTE: If lid is not closed, an invalid button press
beep will occur when performing next step.
Press and
release:
SPIN SPEED, Motor/basket spins at 23 rpm.
WATER LEVEL
or LOAD SIZE
Repeat Motor/basket spins at 530 rpm.
Repeat
Motor/basket spins at ≥ 950 rpm.
Repeat Motor turns off.
NOTE: Indicators above button scroll from top to
bottom.
If motor fails to spin, go to TEST #3, page 4.
Agitate:
Water must cover the wash plate (or agitator
vanes) to ensure the basket is floating prior to
agitation. Enabling agitation without enough water
may cause a fault condition to occur. See Manual:
Water Valves test, at left.
Press and release:
Gentle wash action.
SOIL LEVEL
Repeat
Normal wash action.
Repeat
Heavy wash action.
Repeat
Motor turns off.
NOTE: Indicators above button scroll from top to bottom.
If motor fails to agitate, go to TEST #3, page 4.
Manual: Heater
(If supplied) (See Manual
Activation, at left)
Water must cover the wash plate to ensure the heater
is completely submerged. Heater cannot be enabled
if there is less than 75 mm of water in the machine tub.
Press and release RINSE/DRAIN & SPIN and turn on
the cold valve (See Manual: Water Valves test, at left).
ACTIVATION OF CONSOLE AND
INDICATORS DIAGNOSTIC TEST MODE
This test checks the cycle selector knob, indicators,
buttons, two-digit display and beeper.
1. Plug in washer or reconnect power.
2. From Standby (Off) Mode press and release
(key-dance) the following buttons within 4 seconds:
SOIL WASH/RINSE SOIL
LEVEL TEMP LEVEL
If successful, two-digit will display and you will
have 5 seconds to complete next step.
3. Within 5 seconds of showing in display, press
START (all indicators in display are illuminated and
88
is displayed.
Press START a second time. This turns off the
two-digit display and status indicators except
for the Delay indicator (if present). All other
indicators remain illuminated.
Press START a third time. This turns on the two-
digit display and status indicators except for the
Delay indicator (if present). All other indicators
remain illuminated.
Press DELAY START (DELAY WASH). This turns
off the Delay indicator.
Press DELAY START (DELAY WASH) a second
time. This turns on the Delay indicator.
4. Rotate WASH CYCLE selector back and forth.
Indicators will toggle on (or off).
5. Press buttons to verify function. Indicators will toggle on
(or off) and beep tone will sound when buttons are pressed.
P È I C E
WASH/RINSE
TEMP
o
N W10026634B