Table of Contents
Advertisement
Using Your High-Efficiency Low-Water Washer
1
ADD HE DETERGENT
Follow manufacturer's
instructions to determine amount
of laundry products to use.
4
ADD FABRIC SOFTENER
If desired.
Without Dispenser
6
SELECT WASH TEMP
9
ADD A GARMENT
NOTE: See "Cycle Guide" in the Use and Care Guide for more information about cycles, settings, and options.
Not all cycles, settings, and options are available with all models. Read your Use and Care Guide before using your washer.
W10783949A
W10783950A-SP
© 2015. All rights reserved.
Quick Start Guide
2
LOAD THE WASHER
Add fabric softener during the final rinse.
Press START/PAUSE to pause the washer.
Lift lid and add measured recommended
amount of liquid fabric softener. Close lid
and press START/PAUSE button again to
start the washer.
7
CYCLE OPTIONS
Options vary by model.
During Fill/Sensing, open the lid, add a garment,
close the lid, and press START.
NOTE: Washer will not fill with lid open.
IMPORTANT: If lid is left open for more than
10 minutes, the wash cycle will cancel and the
water will pump out.
3
ADD BLEACH
If desired.
5
SELECT CYCLE
Cycles vary by model.
8
PRESS START
Press and release to start.
NOTE: If you hold Start for more
than 3 seconds, it will cancel your
cycle and drain the washer.
10
CANCELING
WASH CYCLE
Hold START for more than
3 seconds to cancel your cycle
and drain the washer.
Printed in U.S.A.
04/15
Advertisement
Table of Contents
Related Manuals for Whirlpool W10783949A
Summary of Contents for Whirlpool W10783949A
- Page 1 NOTE: See “Cycle Guide” in the Use and Care Guide for more information about cycles, settings, and options. Not all cycles, settings, and options are available with all models. Read your Use and Care Guide before using your washer. W10783949A W10783950A-SP 04/15 ©...
-
Page 2: Table Of Contents
Low-Water Washer consommation d’eau Use and Care Guide avec chargement par le dessus Para una versión de estas instrucciones en español, visite whirlpool.com Table of Contents Table des matières WASHER SAFETY .............2 SÉCURITÉ DE LA LAVEUSE ..........18 WHAT’S NEW UNDER THE LID? ........3 QUOI DE NEUF SOUS LE COUVERCLE? .....19... -
Page 3: Washer Safety
Washer Safety... -
Page 4: What's New Under The Lid
What’s New Under the Lid? Cleaning with Less Water Automatic Load Size Sensing Once you start the cycle, the washer will fill to the water level. When the washer is done filling, it will start to agitate after it determines the correct level for the load. The washer will then fill to the appropriate water level based on the load size. -
Page 5: Control Panel And Features
Control Panel and Features SOIL LEVEL START/PAUSE BUTTON Select the setting most suitable for your load. For heavily Press to start the selected cycle; press again to pause the soiled and sturdy fabrics, select Heavy Soil Level for more cycle and unlock the lid. wash time. - Page 6 RINSE LOCKED You will hear sounds similar to the wash cycle as the The Lock feature allows for higher spin washer rinses and moves the load. You may hear the speeds. When lit, the lid is locked and motor turning on briefly (short hum) to move the basket cannot be opened without pausing the while filling.
-
Page 7: Cycle Guide
Cycle Guide For best fabric care, choose the cycle that best fits the load being washed. Recommended settings for best performance are shown in Bold. Not all cycles and options are available on each cycle. Not all settings and options are available on each cycle. Items to wash: Cycle: Wash Temp*:... -
Page 8: Using Your Washer
Using Your Washer Sort and prepare your laundry Add laundry products • Empty pockets. Loose change, buttons, or any small Add a measured amount of HE object can pass under the washplate and become trapped, detergent or single-dose laundry causing unexpected sounds. packet into the basket. - Page 9 Load laundry into washer Add fabric softener, if desired During the final rinse, wait until the washer has completed filling and press the START/Pause button to pause the washer. Lift the lid and add the measured, For best performance, load items recommended amount of liquid fabric softener.
- Page 10 Select SOIL LEVEL Select cycle options, if desired If you would like to add an extra rinse, fabric softener, or Once you select a cycle, select the soil level by turning the extra soak period to any cycle, turn the knob to desired Soil Level knob to the desired setting.
-
Page 11: Washer Maintenance
Washer Maintenance WATER INLET HOSES WASHER CARE (cont.) Replace inlet hoses after 5 years of use to reduce the risk 2. Chlorine Bleach Procedure (Alternative): of hose failure. Periodically inspect and replace inlet hoses a. Open the washer lid and remove any clothing if bulges, kinks, cuts, wear, or leaks are found. - Page 12 NON-USE AND VACATION CARE REINSTALLING/USING WASHER AGAIN To reinstall washer after non-use, vacation, winter storage, Operate your washer only when you are home. If moving, or moving: or not using your washer for a period of time, follow these steps: 1.
-
Page 13: Troubleshooting
Troubleshooting First try the solutions suggested here or visit our website at whirlpool.com/product_help -In Canada whirlpool.ca for assistance and to possibly avoid a service call. If you experience Possible Causes Solution Vibration or Off-Balance Check the following for Feet may not be in contact with the... - Page 14 Troubleshooting First try the solutions suggested here or visit our website at whirlpool.com/product_help -In Canada whirlpool.ca for assistance and to possibly avoid a service call. If you experience Possible Causes Solution Washer not performing as expected (cont.) Washer won’t run or fill, Check for proper water supply.
- Page 15 Troubleshooting First try the solutions suggested here or visit our website at whirlpool.com/product_help -In Canada whirlpool.ca for assistance and to possibly avoid a service call. If you experience Possible Causes Solution Washer not performing as expected Washer not draining/ Empty pockets and use garment...
- Page 16 Troubleshooting First try the solutions suggested here or visit our website at whirlpool.com/product_help -In Canada whirlpool.ca for assistance and to possibly avoid a service call. If you experience Possible Causes Solution Washer not performing as expected (cont.) Sand, pet hair, lint, etc.
- Page 17 Troubleshooting First try the solutions suggested here or visit our website at whirlpool.com/product_help -In Canada whirlpool.ca for assistance and to possibly avoid a service call. If you experience Possible Causes Solution Washer not performing as expected (cont.) Fabric Damage. Sharp items were in pockets during Empty pockets, zip zippers, and snap or hook fasteners before wash cycle.
-
Page 18: Warranty
DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance, you should ask Whirlpool or your retailer about buying an extended warranty. -
Page 19: Assistance Or Service
Assistance ou Service Avant de faire un appel pour assistance ou service, veuillez vérifier la section “Dépannage” ou consulter www.whirlpool.com/help. Cette vérification peut vous faire économiser le coût d’une visite de réparation. Si vous avez encore besoin d’aide, suivre les instructions ci-dessous.
Need help?
Do you have a question about the W10783949A and is the answer not in the manual?
Questions and answers
I had sheets In soaking , the washer drained and will not start now None of the functions will do anything. How can it reset? It is whirlpool heavy duty commerical washer
To reset the Whirlpool Heavy Duty Commercial Washer (part number W10783949A) after draining, follow these steps:
1. Unplug the washer or disconnect power for a few minutes.
2. Plug the washer back in or reconnect power.
3. Hold the START button for more than 3 seconds to cancel the cycle and drain any remaining water.
4. Ensure the lid is closed properly, as the wash cycle will cancel if the lid is left open for more than 10 minutes.
5. Run the washer through the Bulky Items/Sheets cycle to remove any antifreeze, if used.
If the washer still does not start, check for other possible issues such as power supply problems or improper lid closure.
This answer is automatically generated