Download
 Share
 Print this page
  • Contents

Advertisement

All manuals and user guides at all-guides.com
CONSUMER SERVICES TECHNICAL
L-73
EDUCATION GROUP PRESENTS
ImPress
IRONING STATION
Model LFB2611L
JOB AID
Part No. 8178203
Previous page
Next page

Advertisement

Table of Contents

   Also See for Whirlpool IMPRESS LFB2611L

Whirlpool ImPress LFB2611L Manual
Whirlpool ImPress LFB2611L Manual 24 pages

   Related Manuals for Whirlpool IMPRESS LFB2611L

No related manuals

   Summary of Contents for Whirlpool IMPRESS LFB2611L

  • Page 1 All manuals and user guides at all-guides.com CONSUMER SERVICES TECHNICAL L-73 EDUCATION GROUP PRESENTS  ImPress IRONING STATION Model LFB2611L JOB AID Part No. 8178203...
  • Page 2 • Successfully perform necessary repairs. • Successfully return the Ironing Station to its proper operational status. WHIRLPOOL CORPORATION assumes no responsibility for any repairs made on our products by anyone other than Authorized Service Technicians. Copyright © 2002, Whirlpool Corporation, Benton Harbor, MI 49022...

  • Page 3: Table Of Contents

    Model & Serial Number Designations ................1-2 Model & Serial Number Label And Wiring Diagram Locations .......... 1-3 Specifications ........................1-4 Whirlpool ImPress Ironing Station Warranty ..............1-5 INSTALLATION INFORMATION ................... 2-1 Surface Mounting ....................... 2-1 PRODUCT OPERATION ......................3-1 Adjusting The Board Height ....................
  • Page 4 All manuals and user guides at all-guides.com — NOTES — - iv -...

  • Page 5: General

    All manuals and user guides at all-guides.com GENERAL SAFETY FIRST Your safety and the safety of others is very important. We have provided many important safety messages in this Job Aid and on the appliance. Always read and obey all safety messages. This is the safety alert symbol.

  • Page 6: Model & Serial Number Designations

    All manuals and user guides at all-guides.com MODEL & SERIAL NUMBER DESIGNATIONS MODEL NUMBER MODEL NUMBER L Q 0 INTERNATIONAL SALES IND. OR MARKETING CHANNEL IF PRESENT PRODUCT GROUP: L = DOMESTIC LAUNDRY PRODUCT IDENTIFICATION: F = FINISHING PRODUCTS FEATURE CODE 1: B = BUILT-IN BOARD ONLY FEATURE CODE 2: FIRST DIGIT...

  • Page 7: Model & Serial Number Label And Wiring Diagram Locations

    All manuals and user guides at all-guides.com MODEL & SERIAL NUMBER LABEL AND WIRING DIAGRAM LOCATIONS Model/Serial Number Label Wiring Diagram (Located Behind Panel)

  • Page 8: Specifications

    All manuals and user guides at all-guides.com SPECIFICATIONS Model No. LFB2611LQ & T Color Q = White, T = Biscuit Ironing Board Dimensions: Height 47-1/8″ Width 14-1/4″ General: Electrical Rating 15 Amps Max Current Draw Electrical Outlets One, 3-Prong, Grounded Maximum Iron Rating 1400 Watts Built-in Work Light...
  • Page 9 Whirlpool dealer. If you need service, help can be found by checking the “Assistance Or Service” section of the Use and Care Guide, or by calling the Whirlpool Customer Interaction Center telephone number, 1-800-253-1301, from anywhere in the U.S.A.
  • Page 10 All manuals and user guides at all-guides.com — NOTES —...

  • Page 11: Installation Information

    All manuals and user guides at all-guides.com INSTALLATION INFORMATION SURFACE MOUNTING Determine desired ironing board height ELECTRICAL CONSIDERATIONS above the floor (see the Mounting Height All electrical work must be done in accordance Chart below). NOTE: The ironing station with all applicable electrical codes. enclosure will extend approximately 11″...
  • Page 12 All manuals and user guides at all-guides.com — NOTES —...

  • Page 13: Product Operation

    All manuals and user guides at all-guides.com PRODUCT OPERATION ADJUSTING THE BOARD HEIGHT Rotate the front of the board down to its ironing position. Pull the top of the board forward several inches. ADJUSTING THE SWIVEL TENSION To raise the board: The ironing board can be rotated 360°...

  • Page 14: Using The Iron

    All manuals and user guides at all-guides.com USING THE IRON Place the iron in the hot iron storage compartment in its upright position with Lower the board to the ironing position. the bottom facing the metal heat shield. Plug the iron cord into the grounded re- STORING THE IRONING BOARD ceptacle.

  • Page 15: Component Access

    All manuals and user guides at all-guides.com COMPONENT ACCESS REMOVING THE LIGHT SOCKET, INDICATOR LIGHT, TIMER, AC RECEPTACLE, & CUTOFF SWITCH Lift and remove the iron storage wedge WARNING from the unit. Iron Storage Wedge Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating.
  • Page 16 All manuals and user guides at all-guides.com To remove the light socket: d) Remove 1/2″ of insulation from the cut wire ends, and splice the light socket a) Remove the two screws from the light wires to the wiring harness using two lens and remove the lens, then remove twist-on wire nuts.
  • Page 17 All manuals and user guides at all-guides.com b) Press in on the locking arms, and push c) Disconnect the three wires from the the indicator light out of the component timer terminals. The wires are con- cover. nected as follows: Indicator Terminal 1 = cutoff switch wire Locking Arm...
  • Page 18 All manuals and user guides at all-guides.com To remove the AC receptacle: 10. To remove the cutoff switch: a) Cut the black and white receptacle a) Remove the two wire connectors from wires at the indicated locations shown the switch terminals. below.

  • Page 19: Component Testing

    All manuals and user guides at all-guides.com COMPONENT TESTING Before testing any of the components, perform • Check all connections before replacing com- the following checks: ponents, looking for broken or loose wires, failed terminals, or wires not pressed into •...

  • Page 20: Cutoff Switch

    All manuals and user guides at all-guides.com WARNING Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. Disconnect the power to the ironing sta- CUTOFF SWITCH (N.C.) tion.

  • Page 21: Wiring Diagram

    All manuals and user guides at all-guides.com WIRING DIAGRAM Indicator Light Light Timer Cutoff Switch (Activated By Board When In Upright Position) Grounded Outlet...
  • Page 22 All manuals and user guides at all-guides.com — NOTES —...
  • Page 23 All manuals and user guides at all-guides.com PRODUCT SPECIFICATIONS WARRANTY INFORMATION SOURCES IN THE UNITED STATES: FOR PRODUCT SPECIFICATIONS AND WARRANTY INFORMATION CALL: FOR WHIRLPOOL PRODUCTS: 1-800-253-1301 FOR KITCHENAID PRODUCTS: 1-800-422-1230 FOR ROPER PRODUCTS: 1-800-447-6737 FOR TECHNICAL ASSISTANCE WHILE AT THE CUSTOMER’S HOME CALL:...
  • Page 24 All manuals and user guides at all-guides.com CORPORATION...

Comments to this Manuals

Symbols: 0
Latest comments: