Advertisement
8 8 DO NOT use attachments other than those recommended. To do so may cause damage to the unit and other equipment and possible
8 8
personal injury.
8
8 8 DO NOT pull or carry the unit by its cables and do not pull the negative and positive clamps from the battery terminals.
8 8
8 8 DO NOT operate in vicinity of flammable liquids or gases.
8 8
8 8 DO NOT recharge the unit with plugs, cables or attachments that are damaged. Replace such items immediately.
8 8
8 8 DO NOT use this RoadStart to perform a task for which it is not designed.
8 8
8 8 DO NOT store the unit in damp or wet locations or where the temperature may exceed 50°c.
8 8
8 8 DO NOT submerge the unit in water.
8 8
8 8 DO NOT use whilst under the influence of drugs, alcohol or intoxicating medication.
8 8
8 8 DO NOT leave the unit in a totally discharged state for an extended period of time as this may result in permanent damage to the battery.
8 8
8 8 8 D O NOT cross-connect the power leads from the RoadStart to the battery. Ensure that positive is to positive and negative is to negative.
8 8
Ensure that the unit is fully charged before storage.
9
1.3.
ELECTRICAL SAFETY (with respect to mains chargers)
WARNING! It is the user's responsibility to check the following:
‰
You must check the Ac adaptor to ensure that it is safe before using. You must inspect the power supply lead, plugs and all
electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of appropriate
safety devices. An RccB (Residual current circuit Breaker) should be incorporated in the main distribution board. We recommend that
an Rcd (Residual current device) is used with all electrical products. It is particularly important to use an Rcd with portable products
that plug into an electrical supply not protected by an RccB. If in doubt consult a qualified electrician. You can obtain a Residual
current device through your Sealey dealer. You must read and understand instructions concerning electrical safety.
1.3.1.
The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
person, using a Portable Appliance Tester (PAT), at least once a year.
1.3.2.
The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and
the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.3.3.
Ensure that the insulation on all cables and the product itself is safe before connecting to the mains power supply.
1.3.4.
Ensure that cables are always protected against short circuit and overload.
1.3.5.
Regularly inspect power supply, leads, plugs for wear and damage and power connections to ensure that none is loose.
1.3.6.
check product voltage is the same as power supply to be used.
2. INTRODUCTION
i
composite case with battery clip storage lugs and carry handle. Easily read, colour coded analogue gauge measures battery condition and charge
indicator. Audible warning system for polarity protection. Positive lead fitted with a device to prevent reverse charging from the vehicle. Test cycle
button gives true battery indication. 230V charger with automatic power cut-off prevents damage to battery whilst charging from the mains. Fitted
with 12V power socket that will accept any 12V device with a vehicle accessory plug. Supplied with mains charger.
3. SPECIFICATION
s
Model:.......................................................................RS125.V4
cold cranking Amps: ....................... 12V - 1200A / 24V - 600A
Peak Amps: .................................... 12V - 3000A / 24V - 1500A
Voltage: ................................................ 12V or 24V Switchable
Auxiliary output: ................................................................. 12V
cable and clamp Length: .................................................. 1mtr
Weight: ..............................................................................15kg
WARNING! YOU MUST FOLLOW SAFETY INSTRUCTIONS
4.
CHARGING
Initial Charging Procedure.
4.1.
4.1.1.
When first used, the RoadStart unit should be charged for a minimum of 72 hours. The RoadStart can be left plugged into the mains
indefinitely as the internal PcB has an automatic float charging circuit which will not allow overcharging.
4.2.
Recharging Using the Mains Adaptor.
▲
When recharging, the Voltage Selector MUST be set to 12V.
© Jack Sealey Limited
fig.1
Original Language Version
RS125.V4| Issue:1 10/01/17
Advertisement
