Cleaning And Maintenance; Troubleshooting - Profi Cook PC-SJ 1141 Instruction Manual

CAUTION:
• Do not turn the power switch from "I" to "R" or
from "R" to "I" directly at any time during operation.
If required, first set the power switch in "O" position
to make the appliance stop running completely
and then turn the power switch to "R" or to "I".
• Do not operate the slow juicer before inserting
foodstuffs into the jar (6) to avoid damaging the
grinding assembly.
• Do not at any moment insert your fingers or other
foreign objects into the slow juicer while it is in
operation and still plugged into the power socket.
NOTE:
• During operation, if the slow juicer gets stuck and
is not operable, turn off the appliance by setting
the power switch in the "O" position. Press the
reset button (12) which is located at the bottom
of motor unit (9). After pressing the reset button
press and hold the power switch to the "R" posi-
tion for a few seconds and try operating the slow
juicer again normally. When the reverse function
is not working, turn off the slow juicer and reas-
semble it according to the assembly instructions.
After reassembly turn on the slow juicer again.
• When the juice container (11) is full (the maxi-
mum capacity is approximately 1 L) or the slow
juicer is finished extracting the foodstuffs set the
power switch (10) in the "O" position to turn off
the slow juicer. Empty the contents of the juice
container and residue container (13) before
resuming making more juice.
• Do not leave the slow juicer on for a longer
duration than 15 minutes continuously. Ensure to
have a 30-minute cooling down period between
two operation sessions.
• Ensure not to overfeed the slow juicer. Insert the
foodstuffs in due order so that the slow juicer has
enough time to process it.
• During operation, if the lock of the hopper (2)
manages to get unlocked, the slow juicer will stop
operation automatically in order to avoid potential
hazards.

Cleaning and Maintenance

1. Plug in the slow juicer and turn it on without load
for about 30 seconds after removing the residue. If
the hopper (2) cannot be detached easily, please
follow and repeat the following operation for two or
three times: Reverse — OFF — ON, at the same
time, hold and rotate the hopper to detach it. After
finishing extracting the juice, pour some water into
the hopper to clean it so that it will be easier to
detach.
2. Unlock the hopper (2) by turning it anti-clockwise
and detach it.
3. Detach the rotary cleaning brush (5), strainer (4)
and grinding head (3) in sequence by following the
steps of "Initial Use".
4. Lift the jar (6) to detach it from the motor unit (9).
5. Empty the residue container (13). Clean the hopper
(2), grinding head (3), strainer (4), rotary cleaning
brush (5), jar (6) and residue container (13) under
running water. The small cleaning brush (14) can
be used to properly clean the strainer (4).
CAUTION:
• The strainer (4) has sharp edges, handle with
care during cleaning.
• Do not use any wire brush or other abrasive
objects in order to avoid permanent damage to
the appliance.
• Do not use any acidic or abrasive detergents
in order to avoid permanent damage to the
appliance.
6. If a thorough cleaning of the residue outlet (16)
is required, pull the buffer plate (12) out of the
residue outlet and clean it completely with the small
cleaning brush (14).
7. Wipe the outside of the motor unit (9) with a damp
cloth. Never immerse the motor unit in water.
8. Dry all parts and assemble all parts accordingly
and store the appliance safely in a dry place. The
juice container (11) can be stored in the residue
container (13).

Troubleshooting

Error Remedy
The appli- 1. Check if the power cord is con-
ance does nected properly.
not switch 2. Check if the power switch is in the
on. "I" position.
3. Check if the hopper is locked in
place.
41