Page 3
ENERGY PRODUCTS DESCRIBED HERE IN. Victron Energy B.V. reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication and may not reflect the product at all times in the future www.busse-yachtshop.de | info@busse-yachtshop.de...
Page 5
Read the owners manual carefully before installing the BP! Owners manual BP40 / BP60 / BP200 The new Battery Protect BP40/60/200 (hereafter called BP) is an intelligent, waterproof, Battery Protect with accessory connections for a ON/OFF switch, Alarm buzzer or relay and our CurrentWatch current sensor (not included). The unit has two bolts as connection for the Input+ and the Output+ to guarantee low losses.
Page 6
CurrentWatch The Prog/Current connection can be used to connect a CurrentWatch. The CurrentWatch will show the current used by your equipment. If you are interested in this product, please contact your supplier. Wire cross section Use at least the following wire cross section for the bolt connection: BP40 min 10mm BatteryWatch •...
Page 7
Programming table 12 Volt mode 24 Volt mode Undervoltage Uppervoltage Undervoltage Uppervoltage Threshold Threshold Threshold Threshold Position 1 10,5V 12 V Position 1 21 V 24 V Position 2 10 V 11,5V Position 2 20 V 23 V Position 3 9,5V 11,5V Position 3...
Page 9
Lees de gebruiksaanwijzing eerst aandachtig door alvorens de BP aan te sluiten! Gebruiksaanwijzing BP40 / BP60 / BP200 De nieuwe Battery Protect BP40/60/200 (hierna te noemen BP) is een intelligente, volledig waterdichte, batterij bewaker met uitbreidingsmogelijk-heden voor aan/uit schakelaar, alarm zoemer of relais. De unit is voorzien van twee bout aansluitingen, één Input+ en één Output+, om lage verliezen te waarborgen.
Page 10
BatteryWatch (Optional) FUSE BP40 & BP60 120A • BP200 480A • Afschakelen bij overbelasting na 5 sec. (na 1 minuut weer aan) • Aansluitmogelijkheden • AAN/UIT schakelaar BG40/60 • Alarm zoemer of relais • Input+ Output+ CurrentWatch stroomsensor • Output+ Spanningsval BG200 •...
Page 11
Lisez attentivement le mode d'emploi avant de raccorder le BP ! Mode d'emploi BP40 / BP60 / BP200 Le nouveau Battery Protect BP40/60/200 (nommé ci-après BP) est un contrôleur de batterie intelligent et entièrement étanche, avec des possibilités d'extension pour un connecteur marche/arrêt, un vibreur ou un relais alarme et notre capteur de courant CurrentWatch (non fourni).
Page 12
Diamètre du câble Pour les raccordements à écrous, utilisez au moins les diamètres de câble suivants : BP40 10mm minimum • BP60 15mm minimum • BP200 50mm minimum • Dans des conditions plus rigoureuses, il est conseillé d'utiliser des diamètres plus grands. En cas de surcharge, le BP se déconnectera après 5 secondes et se reconnectera après 60 secondes.
Page 13
Tableau de programmation mode 12 volts mode 24 volts surtension sous-tension surtension sous-tension Position 1 10,5V 12 V Position 1 21 V 24 V Position 2 10 V 11,5V Position 2 20 V 23 V Position 3 9,5V 11,5V Position 3 19 V 23 V Position 4...
Page 15
Lesen Sie die Gebrauchsanweisung zuerst aufmerksam durch, bevor Sie den BP anschlieβen! Gebrauchsanweisung BP40 / BP60 / BP200 Der neue Battery Protect BP40/60/200 (im Folgenden BP genannt), ist ein intelligenter, vollständig wasserdichter Batterieüberwacher mit Erweiterungsmöglichkeiten für An/Aus Schalter, Alarmsummer oder Relais und unserem Current Watch Stromsensor (nicht mitgeliefert).
Page 17
Programmiertabelle 12 Volt mode 24 Volt mode Unter-spannung Ober-spannung Unter-spannung Ober-spannung Position 1 10,5V 12 V Position 1 21 V 24 V Position 2 10 V 11,5V Position 2 20 V 23 V Position 3 9,5V 11,5V Position 3 19 V 23 V Position 4 11,25 V...
Page 21
Serial number: Version : 00 Date : 03 July 2012 Victron Energy B.V. De Paal 35 | 1351 JG Almere PO Box 50016 | 1305 AA Almere | The Netherlands General phone +31 (0)36 535 97 00 Customer support desk...
Need help?
Do you have a question about the Battery Protect Series and is the answer not in the manual?
Questions and answers