Advertisement
noTE: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of
experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible
for their safety. Children should be supervised to ensure that they do not play with the appliance.
2.
INTRODUCTION & SPECIFICATION
Aluminium cylinder with cast iron lining gives reduced weight and improved resistance to wear. Suitable for general purpose workshop
applications. Oil free, single piston pump is belt driven by a 1.5hp motor and fixed to a vertical type tank, saving space around the workshop.
Precision welded receiver tank manufactured to meet Pressure Vessel Directive 2009/105/EC. Fitted with fully automatic pressure cut-out switch
and air regulator with gauge. Supplied with handle and wheels (SAC03050 & SA03290) for easy manoeuvrability. Fitted with ASTA/BS approved
non-rewirable plug.
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SAC03224 . . . . . . . . . . . . .SAC03250 . . . . . . . . . . . . . . . . . . . .SAC03290
motor output: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5hp . . . . . . . . . . . . . . . . .1.5hp . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5hp
Voltage/Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V - 1ph . . . . . . . . . . . . .230V - 1ph . . . . . . . . . . . . . . . . . . . . . 230V-1ph
Rated Supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13A. . . . . . . . . . . . . . . . . . .13A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13A
Air Displacement cfm(ltr/min): . . . . . . . . . . . . . . . . . . 5.6(158) . . . . . . . . . . . . . . .5.6(158) . . . . . . . . . . . . . . . . . . . . . . . . 5.6(158)
maxiimum Free Air Delivery cfm(ltr/min) . . . . . . . . . . 3.32(94) . . . . . . . . . . . . . . .3.32(94) . . . . . . . . . . . . . . . . . . . . . . . . 3.32(94)
maximum Pressure: . . . . . . . . . . . . . . . . . . . . . . . . . 116psi/8bar . . . . . . . . . . . .116psi/8bar. . . . . . . . . . . . . . . . . . . 116psi/bbar
Receiver Capacity: . . . . . . . . . . . . . . . . . . . . . . . . . . 24ltr . . . . . . . . . . . . . . . . . .50ltr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90ltr
Dimensions (W x D x H) . . . . . . . . . . . . . . . . . . . . . . 415 x 415 x 500mm . . . . . . 430 x 455 x 710mm . . . . .430 x 455 x 1035mm
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.8kg . . . . . . . . . . . . . . . .23.4kg . . . . . . . . . . . . . . . . . . . . . . . . . . . .35kg
3. PREPARATION
3.1.
Remove compressor from packaging and inspect for any shortages or damage. If anything is found to be missing or damaged, contact
your supplier.
3.2.
If wheels and/or feet are not fitted to compressor, fit them using the appropriate nuts, bolts and washers supplied.
3.3.
Confirm that the mains voltage corresponds with the voltage shown on the compressor data plate.
4. OPERATION
SAC03224
WARNING! Ensure that you have read, understood and apply Section 1 safety instructions.
4.1.
The compressor should be located and operated in a position that allows good air circulation around the unit. locate the compressor
in a convenient position for the work to be undertaken. Ensure that it is standing on a stable and level surface. Ensure the feet/wheels
are in direct contact with the surface.
4.2.
Attach the required air tool to the air outlet. (fig1.B)
4.3.
Plug the mains plug into a mains electrical socket, but do not switch the compressor on until the workpiece and air tool are fully
prepared.
4.4.
Switch on the unit by pulling the red on/off switch outwards(fig 1.A).
4.5.
The output pressure is regulated by the pressure regulator. (fig 1.C). Turn the regulator knob clockwise to increase pressure to
the required level and vice-versa.The setting can then be retained by tightening the red locking ring below the knob.
When the compressor is not being used, set the regulated pressure to zero so as to avoid damaging the regulator.
4.5.1. The right-hand pressure gauge (fig 1.E) indicates the pressure inside the main tank. The left-hand gauge (fig.1.D) indicates the
pressure supplied to the air equipment. The pressure switch stops the motor when the maximum tank pressure is reached and
restarts it when pressure falls below the minimum threshold - approximately 2bar (29psi) less than the maximum pressure.
© Jack Sealey limited
SAC03224
fig.1
Original Language Version
SAC03250
SAC03250,SAC03290
fig.2
SAC03224,SAC03250,SAC03290
SAC03290
fig.1
fig.3
ISSUE:3(SP) 11/11/13
Advertisement
