Download
Share
Print this page
  1. Manuals
  2. Brands
  3. VIGO Manuals
  4. Enclosure
  5. VG06042A
  6. Installation manual

VIGO VG06042A Installation Manual

Shower enclosure
Hide thumbs Also See for VG06042A:

Advertisement

Quick Links

Download this manual
VIGO INDUSTRIES INSTALLATION GUIDE FOR
SHOWER ENCLOSURE (MODEL VG06042A)
! SAFETY PRECAUTIONS
This Installation Guide uses the following symbols to indicate important information.
Always observe the instructions indicated by these symbols.
!
WARNING
Instructions that, if ignored, could result in death or serious personal injury caused by
incorrect handling or installation of the product. These instructions must be observed for
safe installation.
! CAUTION
The instructions can not be provided for any other installation other than that of the Vigo brand.
The warranty will be voided if the following was not performed properly.
IMPORTANT
Maintenance and other important non-personal injury and non-material damage instructions
or statements that should be observed.
It is highly advised to dry fit the unit prior to any installation.
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the VG06042A and is the answer not in the manual?

Questions and answers

jack
January 22, 2025

hello, if my wall in not plum how do i plum glass pannel

0
1 comments:
Mr. Anderson
May 14, 2025

To plumb a VIGO VG06042A glass panel on an unplumb wall:

1. Ensure sufficient structural support exists behind the shower wall. If not, reinforce it with wooden studs before installation.
2. Dry fit the panel and mark lines on the floor and wall to plan alignment, since the fixed panel does not sit in line with the door panel.
3. Level the front fixed panel in the desired configuration.
4. Mark mounting holes on the wall after leveling.
5. Remove the panel, drill holes, and insert plastic anchors.
6. Reinstall the panel and secure it with screws.

Proper alignment and reinforcement are critical due to the glass panel's fixed shape.

This answer is automatically generated

0

Subscribe to Our Youtube Channel

Related Manuals for VIGO VG06042A

Summary of Contents for VIGO VG06042A

  • Page 1 These instructions must be observed for safe installation. ! CAUTION The instructions can not be provided for any other installation other than that of the Vigo brand. The warranty will be voided if the following was not performed properly. IMPORTANT Maintenance and other important non-personal injury and non-material damage instructions or statements that should be observed.
  • Page 2 MODEL VG06042 PIROUETTE INSTALLATION INSTRUCTIONS FOR SHOWER DOOR Parts List Turning hinge base (1pc) PLEASE READ INSTRUCTIONS BEFORE PROCEEDING Turning hinge base mirrored (1pc) Turning hinge (1pc) Turning hinge mirrored (1pc) Front fixed panel (1pc) Door (1pc) Side seal strip (1pc) Handle assembly (1pc) Side seal strip w/out bump (1pc) Door bottom seal strip (1pc+1pc extra)
  • Page 3 5. FRONT FIXED PANEL 3. TURNING HINGE 4. TURNING HINGE 1. TURNING HINGE 2. TURNING HINGE MIRRORED BASE BASE MIRRORED 98041 98042 98043 98044 97023 6. DOOR 7. SIDE SEAL STRIP - 73" 8. HANDLE ASSEMBLY 9. SIDE SEAL STRIP 10.
  • Page 4 See suggestion of configuration below: CONFIGURATION . 1A CONFIGURATION . 1B CONFIGURATION . 2A CONFIGURATION . 2B (GLASS CONFIGURATION DIAGRAM) LEFT DOOR INSTALLATION RIGHT DOOR INSTALLATION STUD STUD 3/8" 5/8" 3/8" 1" FIG.1 FIG.1A MODEL VG06042...
  • Page 5 Compare items on your invoice with what you have received. Carefully review the Parts List on page 2. If any items are missing, please call Vigo Industries at 1-866-591-7792. Please check our website at www.vigoindustries.com for additional information or instructional videos.

  • Page 6: Installation Steps

    INSTALLATION STEPS INSTALLING THE FRONT FIXED PANEL Arrange the front fixed panel (#5) to the preferred configuration to determine the orientation of glass supports (#29). Install the side seal strip (#7) to the wall side of the front fixed panel. WALL SIDE Screw in the glass support (#29) with the...
  • Page 7 Remove the front fixed panel and drill holes into the wall. Insert plastic anchors (#17) into the holes. Not necessary if installing into studs. Studs are the preferred means of installation, anchors can pull out of the wall causing property damage and bodily harm.
  • Page 8 INSTALLING THE TURNING HINGE BASE Unscrew the plate on the turning hinge base mirrored (#2) and mount the turning hinge PLATE base mirrored into the lower corner of the INSIDE VIEW front fixed panel (#5). OUTSIDE VIEW Mark a hole on the floor for the mounting screw for the turning hinge base mirrored.
  • Page 9 Remove the turning hinge base mirrored and drill a hole into the floor on the marked location. Insert plastic anchor (#16) into the hole. Mount the turning hinge base mirrored again, carefully cover the plate and tighten the screw (supplied) from inside the shower . PLATE INSIDE VIEW OUTSIDE VIEW...
  • Page 10 Screw the turning hinge base mirrored into the floor with 1 1/8 " Phillips screw (#15). Make sure the glass panel is perpendicular to the wall. Remove the screw that connects the structural arm on the floor mount portion of part (#2).
  • Page 11 Mount the turning hinge base (#1) to the upper corner of the front fixed panel, cover the plate and tighten the screw (supplied) from inside the shower. PLATE INSIDE VIEW INSTALLING THE STRUCTURAL ARM 1/2" TOLERANCE ADJUSTMENT Attach the structural arm (#30) to the top turning hinge base (#1) .
  • Page 12 Mark two holes on the wall for the mounting screws for the structural arm (#30). Remove the structural arm (#30) from the top turning hinge base and drill holes into the wall at the marked locations. Insert plastic anchors (#16) into the holes. MODEL VG06042...
  • Page 13 Resecure the structural arm to the turning 1/2" TOLERANCE hinge base and tighten the screw (supplied) ADJUSTMENT connecting the turning hinge base and the structural arm. INSIDE VIEW OUTSIDE VIEW Screw the structural arm into the wall with 1 5/8 " phillips screws (#14) making sure it is firm and plum to the wall and keeping the MODEL VG06042 MODEL VG06042...

  • Page 14: Installing The Door Panel

    INSTALLING THE DOOR PANEL Insert the convex portion of the turning hinge mirrored (#4) into the concave point of the turning hinge base mirrored (#2). One installer manually inserts the convex portion of the turning hinge (#3) into the concave portion of the turning hinge base (#1) and holds the position.
  • Page 15 The other installer lifts the door panel (#6) and gently slides it into both turning hinges at the same time. Stop the sliding of the door panel at the proper location based on the pre-determined configuration or the specific site space requirements. Make sure the plastic (PVC) washers do not move from their desired position and wrap the glass...

  • Page 16: Installing The Handle

    Tighten three screws (supplied) on both turning hinges from inside the shower, respectively, making sure the door panel is tightly secured by these two hinges and level. INSIDE VIEW INSTALLING THE HANDLE Unscrew the handle holders from the handle CLEAR WASHER assembly (#8).
  • Page 17 INSTALLING SEAL STRIPS Install the door side seal strip (#12) to the door when the door edge towards the wall is away from the turning hinge base (#1). If maximum length of the shower enclosure is required and the door edge is within rubbing distance of the glass support install the side seal strip without bump (#9).
  • Page 18 3. Install Door side seal strip (#23) the door panel. 9 or 12 MODEL VG06042 MODEL VG06042...
  • Page 19 INSTALLING THE DOOR THRESHOLD 1. Measure the distance from side to side under the door and cut the threshold to the proper length. Note that there are screw holes on VIEW WITH PART 4 REMOVED both sides of the threshold, this makes the unit reversible.
  • Page 20 3. Remove the threshold end cup and mark a hole on the floor for the threshold screw. VIEW WITH PART 4 REMOVED Mark hole on the floor here 4. Remove the door threshold and drill hole into the floor. Insert plastic anchor (#16) into the hole.
  • Page 21 INSTALLING SCREW COVERS Install screw covers (#24) to the unit. Please pay attention that there are three types of covers. Type A is for structural arm (3pc). Type B is for turning hinges (6pc). Type C is for glass supports (4pc). TYPE A TYPE B TYPE C...
  • Page 22 In order to keep your shower enclosure in optimal working condition, Vigo recommends regularly inspecting your enclosure and tightening any hardware that may have loosened during use. This simple step will insure optimal results from your Vigo shower enclosure for many years to come.