Page 1
It is highly advised to dry fit the unit prior to any installation. *VIGO reserves the right to modify/update all hardware and glass components based on bettering the product for the end user's experience. If you have any questions contact VIGO Tech Support at 1-866-591-7792.
Page 2
MODEL VG6046 CASPIAN INSTALLATION INSTRUCTIONS FOR SHOWER DOOR PLEASE READ INSTRUCTIONS BEFORE PROCEEDING Parts List 1. Plastic anchors white (4pc) 9. Door threshold cap (2pc) 2. Wall mount bracket (2pc) 10. Phillips screw 3/4" (4pc) 3. Hex screw 1 5/8" (4pc) 11.
Page 3
A, B & C DIMENSIONS WERE MEASURED AFTER SHOWER ENCLOSURE WAS COMPLETELY INSTALLED Product lines may change, contact your Vigo representative at 1-866-591-7792 or visit our website at www.vigoindustries.com for the most up to date product line information. MODEL VG6046...
Compare items on your invoice with what you have received. Carefully review the Parts List on page 2. If any items are missing, please call Vigo Industries at 1-866-591-7792. Please check our website at www.vigoindustries.com for additional information or instructional videos.
IMPORTANT Verify that the overall size of the shower door opening is appropriate for the shower enclosure. Due to individual site variations, exact guidelines for every situation cannot be supplied. The recommended framing and dimensional requirements are shown for a typical application and may vary depending on the site requirements.
Page 6
Measure *70 5/8" and 71 9/16" from the floor or curb of base. Mark these locations. The dimension supplied These measurements will be the center of is measured at the center of the wall mount bracket. each hole in your wall mount bracket assembly plate (#2).
Page 7
Remove the rail from the dry fit and remove the wall mount brackets (#2) from the structural rail (#4). Line the outside of the wall mount brackets with the markings on the wall. With the MARK THE TWO HOLES ON THE plates still installed to the wall mount WALL WITH A brackets mark the wall at the center of the...
Page 8
Replace the plates and screw them into the plastic anchors with the hex screws (#3). Preferred method of installation PLATE negates anchors and has the installation going right into the studs. PLATE Slide the bracket body (#2) in position on the structural rail (#4).
Page 9
INSTALLING THE INNER DOOR PANEL Screw the double rollers (#8) to the inner door panel (#7) using the allen key COVERS supplied. Once tightened, place the covers INSIDE OF on the rollers. THE SHOWER MODEL VG6046...
Page 10
Position the inner door panel (#7) into the back of the structural rail (#4). Find the center point of your shower opening and mark a line. CENTER OF SHOWER OPENING MODEL VG6046...
Page 11
Position the bottom door guide (#13) on top of the center line you marked. Verify that the inner door panel (#7) rests in the back notch of the bottom door guide. Level the inner door panel (#7) and mark the location of the bottom door guide (#13).
Page 12
Remove the bottom door guide (#13) and door threshold (#11). Drill the holes and place the green plastic anchors (#12) inside them. Replace the door bottom guide (#13) and door threshold (#11) and screw them to the floor with 3/4" screws (#10). Place the door threshold cap (#9) over the end of the threshold and slide it towards the wall.
Page 13
Position the inner door panel (#7) back into the structural rail (#4) and bottom door guide (#13). INSTALLING THE OUTER DOOR PANEL Screw the single rollers (#14) to the outer door panel (#15) using the allen key supplied. Once tightened, place the covers INSIDE OF THE SHOWER on the rollers.
Page 14
Place the two top rollers and the outer door panel (#15) assembly onto the structural rail (#4). Verify that the bottom of the door rests in the front notch of the bottom door guide (#13). MODEL VG6046...
Screw the two bottom roller guides (#18) to the door panel (#15) using the allen key supplied. INSIDE OF THE SHOWER SMALL HEX HOLE INSTALLING THE HANDLE Install the handles (#6) as shown. CLEAR WASHER GLASS SUPPORT CLEAR WASHER HEX SCREW OUTSIDE HEX SCREW HANDLE...
Page 16
INSTALLING THE DOOR SEAL STRIPS Attach the door seal strips (#5 and #17) to the inner door panel and the outer door panel, respectively. Start at the bottom and work your way up, using the heel of your hand to firmly press the seal strip onto the glass.
Page 17
In order to keep your shower enclosure in optimal working condition, Vigo recommends regularly inspecting your enclosure and tightening any hardware that may have loosened during use. This simple step will insure optimal results from your Vigo shower enclosure for many years to come.
Page 18
VIGO or an authorized VIGO dealer. VIGO warrants the seal strip components of the Product to be free from defects in workmanship and materials under normal use and service for a period of one (1) year from the initial date of purchase by the owner or end-user, contractor, or builder, from VIGO or an authorized VIGO dealer.
Need help?
Do you have a question about the CASPIAN VG6046 and is the answer not in the manual?
Questions and answers