Advertisement
Quick Links
Leave this manual with party responsible for use
and operation.
1. Introduction
The IntelliFire™ Touch auxiliary control module (IFT-
ACM) is an AC powered device that controls peripheral
devices such as lights, fans and Power Vents approved
for use in Hearth & Home Technologies products that are
equipped with Intellifire™ Touch technology. It is con-
nected to and controlled by the Intellifire™ Touch Elec-
tronic Control Module (IFT-ECM).
2. IFT-ACM Installation
A. Precautions
f i r e - p a r t s . c o m
This device is tested and safe when installed in accor-
dance with this installation manual. Do not install any
components that may be damaged.
Do not modify, disassemble, or substitute any of the com-
ponents included with this kit. Installation of this unit must
be done by a qualified service technician.
The location of this device may affect performance. An
assessment of the location should be done prior to instal-
lation for optimum performance.
Hearth & Home Technologies disclaims any responsibility
for, and the warranty will be voided by, the following actions:
• Installation and use of any damaged system component.
• Modification of the system component.
• Installation other than as instructed by Hearth & Home
Technologies.
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Any such action may cause a fire hazard.
• Read, understand and follow these instructions for safe
installation and operation.
1
IntelliFire™ Touch Auxiliary Control Module
Installation Instructions
Hearth & Home Technologies • IFT-ACM Installation Instructions • 2326-988 • 9/16
IFT-ACM
B. Determine Location
The IFT-ACM latches to the IntelliFire™ Touch elec-
tronic control module (IFT-ECM). Remove any material
or objects in the immediate vicinity of the vents on the
IFT-ACM. These vents allow the IFT-ACM to dissipate
excess heat into the air.
The IFT-ACM is approved for interior installation only
and should not be used in exterior installations.
Any additional peripheral devices such as lights, fan
and/or Power Vent must be installed as shown in the ap-
pliance manual.
C. Kit Contents
• IntelliFire™ Touch Auxiliary Control Module (IFT-ACM)
• Power cable that connects AC receptacle to IFT-ACM
• 1 inch sq. Piece of Velcro
D. Installation Steps
CAUTION! Do not install damaged components. If you
received components that are damaged, contact your
dealer for assistance.
1. Remove the contents from the packaging.
2. Locate the IFT-ECM in the control cavity of the appli-
ance and move the three-position switch to the OFF
position. See Figure 1.
3. Remove protective rubber cap from connector on the
top of the IFT-ECM. See Figure 1.
Figure 1. IFT-ECM
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Hearth & Home IntelliFire IFT-ACM
Summary of Contents for Hearth & Home IntelliFire IFT-ACM
- Page 1 IFT-ACM IntelliFire™ Touch Auxiliary Control Module Installation Instructions B. Determine Location Leave this manual with party responsible for use and operation. The IFT-ACM latches to the IntelliFire™ Touch elec- tronic control module (IFT-ECM). Remove any material or objects in the immediate vicinity of the vents on the 1.
- Page 2 4. Attach velcro included with the IFT-ACM to the bottom POWER CORD of the ACM. See Figure 2. 5. Connect the IFT-ACM to the IFT-ECM by aligning the pins and tabs and pushing the IFT-ACM into the IFT- ECM until both tabs latch in place. Ensure the IFT- ECM and IFT-ACM are aligned with each other and fastened securely.
-
Page 3: Green Led
E. Pairing the IFT-RC400 to the Electronic Control Module (IFT-ECM) CAUTION! Risk of Burns! DO NOT program the IFT Remote Controls to the IFT-ECM when flame or cold climate function is on or when appliance is hot. 1. On the IFT-ECM, move the ON/OFF/REMOTE switch to the REMOTE position. - Page 4 F. Wiring Diagram IntelliFire™ Touch System Wiring Diagram without Power Vent FLAME IFT-RC400 IGNITER SENSE REMOTE (OPTIONAL ON SOME CONTROL ADAPTER MODELS ONLY) MODULE RESET SWITCH WIRE ASSEMBLY TO JUNCTION BOX 110-120 IFT-RC150 WIRELESS WALL SWITCH f i r e - p a r t s . c o m (OPTIONAL) RF MODULE GRN/WHT/BLK...
- Page 5 F. Wiring Diagram (continued) IntelliFire™ Touch System Wiring Diagram with Power Vent FLAME IGNITER SENSE (OPTIONAL ON SOME ADAPTER MODELS ONLY) MODULE IFT-RC400 RESET REMOTE WIRE ASSEMBLY SWITCH CONTROL TO JUNCTION BOX 110-120 f i r e - p a r t s . c o m RF MODULE GRN/WHT/BLK FAN 110-120 VAC...
-
Page 6: Frequently Asked Questions/Troubleshooting
3. Frequently Asked Questions/Troubleshooting Symptom Possible Cause Corrective Action Refer to Section D9 and make sure that the pairing procedure If IFT-ACM was newly installed has been followed especially if the IFT-ACM was newly in- and not paired. stalled. The IFT-ACM does not respond to The power cord between Refer to Section D6 and make sure the power cable is properly commands from the IFT-RC400... - Page 7 f i r e - p a r t s . c o m Please contact your Hearth & Home Technologies dealer with any questions or concerns. For the location of your nearest Hearth & Home Technologies dealer, please visit www.hearthnhome.com. Hearth &...
Need help?
Do you have a question about the IntelliFire IFT-ACM and is the answer not in the manual?
Questions and answers