Table of Contents
Advertisement
Quick Links
IntelliFire Touch
Leave this manual with party responsible for use
and operation.
1. Introduction
The IntelliFire Touch
2.0 Premium Auxiliary Control Mod
®
ule (IFT2PACM) is an AC powered device that controls
peripheral devices such as lights, fans, heat manage ment
systems, power vents and secondary burners approved
for use in Hearth & Home Technologies (HHT) products
that are equipped with IntelliFire Touch technol ogy. It is
connected to and controlled by the IntelliFire Touch 2.0
Electronic Control Module (IFT2ECM).
NOTICE! The PACM only operates with the IFT2-ECM.
2. Installation
A. Precautions
The IFT2PACM is tested and safe when installed in ac
cordance with this installation manual.
• DO NOT install any of the components included with
this kit if they may look damaged.
• DO NOT modify, disassemble, or substitute any of the
components included with this kit.
• Installation of this kit MUST BE DONE by a qualified
service technician.
• The IFT2PACM is approved for interior installation only
and should not be used in exterior installations.
• Any additional peripheral devices such as lights, fan,
heat management systems, secondary burner, and/or
power vent must be installed as directed in the appliance
Installation manual or accessory instructions.
NOTICE! Keep remote control out of reach of children.
Hearth & Home Technologies disclaims any responsibility
for, and the warranty will be voided by, the following actions:
• Installation and use of any damaged system component.
• Modification of the system component.
• Installation other than as instructed by Hearth & Home
Technologies.
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Any such action may cause a fire hazard.
• Read, understand and follow these instructions for safe
installation and operation.
1
Hearth & Home Technologies • IFT2-PACM Installation Instructions • 2564-982 Rev. B • 6/23
IFT2-PACM
2.0 Premium Auxiliary Control Module
®
Installation Instructions
B. Kit Contents
• IFT2PACM Control Module
• AC Input Power Cord
• 1 inch sq. Piece of Velcro
C. Installation Steps
WARNING! Risk of Shock! DO NOT touch male pins.
Leave rubber cap on all the cap-on receptacles unless the
receptacle is connected to an accessory kit.
CAUTION! Do not install damaged components. If you
received components that are damaged, contact your
dealer for assistance.
1. Remove the contents from the packaging.
2. Locate the IntelliFire Touch electronic control module
(IFT2ECM) in the control cavity of the appliance and
move the threeposition switch to the OFF position.
See Figure 1.
3. Remove protective rubber cap from connector on the
top of the IFT2ECM. See Figure 1.
THREE POSITION SWITCH
THREE POSITION SWITCH
Figure 1 IFT2-ECM
PACM CONNECTOR
PACM CONNECTOR
FAN
FAN
PAIRING HOLE
PAIRING HOLE
LED INDICATOR
LED INDICATOR
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Hearth & Home IntelliFire Touch 2.0
Summary of Contents for Hearth & Home IntelliFire Touch 2.0
- Page 1 IntelliFire Touch technol ogy. It is Leave rubber cap on all the cap-on receptacles unless the connected to and controlled by the IntelliFire Touch 2.0 receptacle is connected to an accessory kit. Electronic Control Module (IFT2ECM).
- Page 2 4. Attach velcro included with the PACM to the bottom of 6. The IFT2PACM can provide power to HHT approved the PACM. See Figure 2. kits including fan, lights, power vent, four heat man agement outputs and secondary burner. • To connect a 120 VAC fan to the PACM, insert the VELCRO threepronged male plug from the fan into the re...
- Page 3 D. Re-Pairing existing IFT2-RC450 after add- PAIRING HOLE PAIRING HOLE ing IFT2-PACM, blower kit, light kit or REMOTE POSITION REMOTE POSITION power vent NOTICE! Pairing the IFT2-RC450 to the IFT2-ECM is NOT REQUIRED when adding the IFT2-PACM. Connect the AC input power and peripheral accessories to the IFT2-PACM, then move the IFT2-ECM slider switch to the REMOTE position.
-
Page 4: Wiring Diagram
E. Wiring Diagram Refer to appliance Installation Manual for product specific wiring diagram. IntelliFire Touch 2.0 System Wiring Diagram ® FLAME IGNITER IFT2-RC450 SENSE REMOTE CONTROL 6 VDC POWER (OPTIONAL ON SOME (OPTIONAL) ADAPTER MODELS ONLY) MODULE RESET WIRE ASSEMBLY SWITCH IFT-WFM TO JUNCTION... - Page 5 3. Operation Thermostat Introduction NOTICE! This feature is only available for use on heater- This user manual serves as a quick reference to the rated appliances. Decorative appliances are shipped from screen, functions and indicators on your IntelliFire Touch the factory with the thermostat function disabled. IFT2RC450 Remote control.
-
Page 6: Accent Lights
Heat Management FUNCTIONS FUNCTIONS Heat-Zone (HM1) If your appliance offers heat management and you wanted Thermostat with Heat Management to have a HeatZone option, it would be connected to the HM1. HM1 will automatically turn on the heat zones when Depending on the HM1HM4 PACM outputs your appli... -
Page 7: Diagnostics Menu
FUNCTIONS FUNCTIONS INDICATORS INDICATORS Fan Speed* Temperature Display If your appliance is equipped with the fan feature, use You can toggle the temperature display between °F and this function to increase or decrease the amount of heat °C by tapping on the Room Temperature display. released into your room. -
Page 8: Backup Battery
Sorry your appliance did not start. INDICATORS INDICATORS Try again by pressing Flame On. Your appliance did not start during the last Flame On Backup Battery command. Verify that you have power and gas to your appliance. Press the Turn Flame ON icon again, verify The battery life indicator is for a backup power source that the appliance accepts command with an audible for the IFT2ECM located inside your appliance. -
Page 9: Maintenance
Maintenance INDICATORS INDICATORS Your appliance will remind you to schedule routine ser vice after 300 hours of Flame ON time is accumulated. Replace Remote Batteries Please contact your dealer for a 300 hour inspection to ensure your appliance is operating at peak performance. Must Replace Remote Batteries to Operate 1. -
Page 10: Frequently Asked Questions/Troubleshooting
4. Frequently Asked Questions/Troubleshooting NOTICE! Please contact your Hearth & Home Technologies dealer if the Corrective Actions do not resolve the issues with your appliance. Symptom Possible Cause Corrective Action The appliance does not Batteries are depleted. Install NEW batteries. respond to commands from the RC450 or display does Batteries are incorrectly... - Page 11 Frequently Asked Questions/Troubleshooting (continued) Symptom Possible Cause Corrective Action The RC450 displays the following message on screen: “Replace Remote Batteries” Low batteries in the RC450. Install new batteries in the RC450. or “Must Replace Remote Batteries to Operate Appliance”. Call dealer to have them program the RC450 with cor The RC450 is displaying an The RC450 was programmed rect branding.
- Page 12 Frequently Asked Questions/Troubleshooting (continued) Symptom Possible Cause Corrective Action PACM was newly installed Make sure that the pairing procedure has been followed and not paired. especially if the PACM was newly installed. The PACM does not respond The power cord between Make sure the power cable is properly inserted into the to commands from the PACM and junction box is...
- Page 13 Frequently Asked Questions/Troubleshooting (continued) Symptom Possible Cause Corrective Action RC450 displays the No gas to appliance. Verify that appliance has power and gas. Verify that the following message on screen: Accumulation of air in gas appliance accepts flame ON commands with an audible “Sorry your appliance did not line from extended period beep, and successfully turns flame on within 90 seconds.
Need help?
Do you have a question about the IntelliFire Touch 2.0 and is the answer not in the manual?
Questions and answers