Technical Specifications - LG Therma V AHUW056A3 Engineering Product Data Book

THERMA V
Split Type
3. Specifications
 Technical Specifications
Indoor Unit Model Name
Cooling
Operation
(Min.~Max.)
Range
Heating
(Leaving
(Min.~Max.)
Water)
Domestic Hot Water (Min.~Max.)
Operation Range (Ambient)
Type
Material
Water Volume
Internal Thermal Protect limit
DHW Tank Maximum water temperature
Maximum water pressure limit
Insulation
Water Volume
Buffer Tank Material
Insulation Material
Type
Model
Motor type
Steps of Speed
Water Pump
Power input
Water Flow Rate
Pressure drop
Type
Quantity
Heat
Exchanger Water Volume
(Water Side)
Water Flow Rate (Min. ~ Max.)
Insulation Material
Safety Valve Pressure Limit
Devices for Water Circuit
Refrigerant
Circuit
Water
Piping
Circuit
Connections
DHW Tank
Water
Circuit
Sound Pressure Level
Sound Power Level
Dimensions (W × H × D)
Weight
(without water)
Note
1. Due to our policy of innovation some specifications may be changed without notification.
2. Wiring cable size must comply with the applicable local and national code. And "Electric characteristics" chapter should be considered for electrical
work and design. Especially the power cable and circuit breaker should be selected in accordance with that.
3. Sound Level Values are measured at Anechoic chamber. Therefore, these values depend on the ambient conditions and values are normally higher
in actual operation.
4. Capacities are net capacities and based on the following conditions. Refer to the Outdoor Unit Specifications for calculating the real capacity.
• Cooling : Indoor Water Temp. 23°C / 18°C, Outdoor Ambient Temp. 35°CDB / 24°CWB
• Heating : Indoor Water Temp. 30°C / 35°C, Outdoor Ambient Temp. 7°CDB / 6°CWB
• Interconnected Pipe is standard length and difference of Elevation (Outdoor ~ Indoor Unit) is Zero.
5. Sound pressure levels at a distance of 1m.
6. This is true for pipe connections of suitable dimensions and joint distance of up to 20m.
Pipe dimensions and types of pumps must always be verified or determined by the designing engineer of electrical installations.
Circulation pumps must be dimensioned in such a way so as to ensure rated voltage (see table) through the device.
4
For Fan Coil Unit
For under floor
For Fan Coil Unit /Radiator
For under floor
Rated
Material
Thickness
Heat loss (for 24hr)
Rated
Min.
Rated
Max.
Max.
Gas (Outer Dia.) mm(inch)
Liquid (Outer Dia.) mm(inch)
Inlet (Inner Dia.) mm(inch)
Outlet (Inner Dia.) mm(inch)
Cold Inlet (Outer Dia.) mm(inch)
Hot Outlet (Outer Dia.) mm(inch)
Recirculation (Outer Dia.) mm(inch)
Unit
Shipping
Unit
Shipping
AHNW16606B0 [HN1616T NB0]
°C
°C
°C
°C
°C
°C
Hydro module with integrated boiler
-
°C
°C
bar
-
mm
kWh
-
-
- Canned type for hot water circulation
- Yonos PARA RS25/7 PWM1
-
EA Variable speed 13% to 100%
W
/ min
/ min
kPa
-
-
/ min
-
bar
-
-
-
-
dB(A)
dB(A)
mm
mm
kg
kg
DHW Tank Integrated Unit
7 ~ 25
7 ~ 25
25 ~ 58
25 ~ 58
10 ~ 60
5 ~ 35
Enameled steel
200
95
52
10
Polyurethane foam
50
1.67
40
Steel powder coated
Closed cell foamed rubber
BLDC
3 ~ 45
16.0
46.0
70
Brazed Plate HEX
1
3.3
13 ~ 70
Closed cell foamed rubber
3
Manometer
Drain Valve / Fill Valve
Shut Off Valve
Air Vent
Ø 15.88 (5/8)
Ø 9.52 (3/8)
Male PT 25 (1)
Male PT 25 (1)
Male PT 19.05 (3/4)
Male PT 25 (1)
Male PT 19.05 (3/4)
27
36
607 × 2,079 × 725
640 × 2,195 × 790
228
238