Table of Contents
Advertisement
Quick Links
MADE IN CONNECTICUT !
If for any reason, you cannot follow these instructions, FOR
ANY REASON WHATSOEVER
Please hire a plumber or Qulified Installer
not use this product if you cannot follow these instructions.
The Verona Burner System is designed, and intended, for
installation in an existing approved, fully vented, wood- burning
fireplace, which includes gas hook-up. Gas Control Valve units
may be fueled by, either Natural Gas or Liquid Propane. Liquid
Propane must be orderd as such, DO NOT Connect the Unit with
any fuel other than is intended !
DO NOT INSTALL IN A WOOD BURNING STOVE
NEVER OPERATE WITH CLOSED GLASS DOORS !
GENERAL INFORMATION
These instructions are intended as a general guide and do not
supersede national or local codes in any way. Authorities
having jurisdiction should be consulted before installation.
Installation and provision for combustion and ventilation air
must conform to the National Fuel Gas Code, ANSI
Z223.1/NFPA 54, or CAN/CGA-B149.1, Natural Gas
Installation Code, or CAN/CGA-B149.2, Propane Installation
Code.
.
!!! IMPORTANT !!!
Read these instructions carefully before installing or operating
this gas appliance. These instructions should be left with the
homeowner for future reference.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
If the information in this manual is not followed exactly, a fire or
explosion may result causing property damage, personal injury
or loss of life.
VERONA
Gas Burner System
!!! WARNING !!!
This appliance must be installed only in a solid-fuel burning
fireplace with a working flue and constructed of non-
combustible materials. This unit is NOT for use with solid fuel.
Solid fuels shall NOT be burned in a fireplace where a
decorative appliance is installed.
by FIAMMA Manufacturing llc
WHAT TO DO IF YOU SMELL GAS:
do
<
Do not try to light any appliance.
<
Do not touch any electrical switch; do not use
any phone in your building.
<
Immediately call your gas supplier from a
instructions.
<
If you can not reach your gas supplier, call the
fire department.
Do not store combustible materials or use gasoline
or other flammable vapors and liquids in the vicinity
of this or any other appliance.
Installation and service must be performed by a:
Qualified technician, service agency, or the gas
supplier.
Your unit was test fired and Inspected prior to shipment.
Any discoloration on the Burner or pilot is due to the test fire
!!! WARNING !!!
NEVER OPERATE THIS APPLIANCE WITH
1
LLC.
. Follow the gas s
!!! DANGER !!!
FIREPLACE GLASS DOORS CLOSED !
Advertisement
Table of Contents
Related Manuals for Fiamma VERONA
Summary of Contents for Fiamma VERONA
- Page 1 < Do not try to light any appliance. The Verona Burner System is designed, and intended, for installation in an existing approved, fully vented, wood- burning < Do not touch any electrical switch; do not use fireplace, which includes gas hook-up.
-
Page 2: Safety Information
SAFETY INFORMATION < WARNING: Follow all gas leak check procedures in this manual, prior to operation. < WARNING: Fuels used in gas or oil fired appliances, and the products of combustion of such fuels, contain chemicals known to the State of California to cause cancer, birth defects, and/or other reproductive harm. - Page 3 10% ( 2 orifice sizes ) at altitudes from 2000 ft. to 4500 ft.. Front Width Minimum 6" larger than unit size Center Width Not Less than unit size Depth All Verona Burners are 8.5 inches deep Height Minimum 16"...
-
Page 4: Installation
VERONA BURNER SYSTEM VERONA 42 BURNER SYSTEM FRONT VIEW NOTE: Verona 23" and 30" are a single Burner. Verona 42" is A double Burner system, All Controls and functions are the same. WHEN INSTALLING THE APPLIANCE, DO NOT OBSTRUCT THE FLOW OF COMBUSTION AND VENTILATION AIR. -
Page 5: Setup And Assembly
Apply Teflon tape or pipe dope to the steel fittings before making any connection. NOTE: All gas connections ( except for brass to brass ) require Teflon tape or pipe dope. The Verona has 2 acccess openings and one air intake. Under NO circumstances, can either the Valve access or the air intake in rear of Unit be Blocked. - Page 6 FIGURE 6 One Side of the Verona has a steel cover with 2 Phillips screws, This conceals rhe Remote Receiver ( FIGURE 6 ) This is an Inside View of the Reciever behinde the steel cover ( FIGURE 7 ) To replace 4 AA Batteries, remove this cover...
-
Page 8: Operation
FINAL SET UP !!! WARNING !!! Failure to position the parts in accordance with all included pictures, diagrams, and drawings, or failure to use only parts specifically approved with this appliance may result in property damage or personal injury. FIGURE 12 FIGURE 13 WARNING: DO NOT apply extra material not supplied or approved with this appliance. -
Page 9: Lighting Instructions
If not, repeat the aforementioned steps. If pilot Your Verona Burner should be thoroughly ignition does not take place, contact your installer or the Fiamma Service Center. inspected on a regular basis, at least once a year, by a qualified installer. -
Page 10: System Troubleshooting
SYSTEM TROUBLE SHOOTING PROBLEM OBSERVED POSSIBLE CAUSE CORRECTIVE MEASURE Gas odor during set up Gas leak See " What to do if you smell gas " page 1 Check all gas connections Gas odor before first ignition Gas leak See " What to do if you smell gas " page 1 Check all gas connections Make sure gas is on, in pilot position Pilot will not ignite, or will not stay lit... -
Page 11: Year Limited Warranty
The item listed are warranted as follows for the period of time specified. Fiamma LLC. does not authorize any person or company to assume for it any other obligation or liability in connection with the sale, installation, This Limited Warranty does not cover any failures or operating use, removal, return, or replacement of its equipment;...