Digoo DG-TH3330 Quick Start Manual

Digoo DG-TH3330
3 channels in&out hygro- thermometer
Monitor Front
A.
B.
C. D. E.
Monitor Back
1. 2. 3. 4. 5.
Monitor Front:
A. Time
B. Indoor Temperature
C. Channel 1 Outdoor Temperature and Humidity
D. Channel 2 Outdoor Temperature and Humidity
E. Channel 3 Outdoor Temperature and Humidity
F. Indoor Relative Humidity
G. Date
Outdoor Sensor:
G.
F.
Remote Sensor:
6.
7. TX Button
8. Channel 1, 2, 3 Slide Switch
9. Transmission Indication LED
Important Placement Guidelines
• To ensure accurate temperature measurement, place units out of direct sunlight and away from any
heat sources or vents.
• Display unit and outdoor sensor must be within 99ft(30m) of each other.
• To maximize wireless range, place units away from large metallic items, thick walls, metal surfaces, or
other objects that may limit wireless communication.
• To prevent wireless interference, place both units at least 3ft(.9 m) away from electronic devices(TV,
computer, microwave, radio, etc.)
Monitor Back:
1. SET Button
2. ALARM Button
3. UP / MEM Button
4. DOWN / CF Button
5. CH Button
6. SNZ/LIGHT Button
9.
7.
AT
LEAST
TV
3 feet
(0.9 m)
APART
(99 feet maximum)
(30 meters)
1.0 Care of the Device
• Avoid exposing units to extreme temperatures or severe shock.
• Avoid contact with any corrosive materials such as perfume, alcohol or cleaning agents.
• Do not subject the units to excessive force, shock, dust, temperature or humidity. Any of these
conditions may shorten the life of the units.
• Do no tamper with any of the internal components of these units. This will invalidate the
warranty and may cause damage.
• Damage caused by failure to comply with this instruction manual will invalidate any warranty.
The manufacturer and supplier will not be held liable for any damages due to failure to comply
with this instruction manual.
• In case of harm or damage to a person or property caused by improper handling or failure to
comply with this instruction manual, the manufacturer and supplier cannot be held liable.
• This product is not to be used for medical purpose or for public information.
1.1 Correct Usage of Batteries
• Do not mix standard and rechargeable batteries.
• Do not mix new and old batteries.
8.
• When the low battery symbol
• Do not leave discharged batteries in the device as these may corrode and release chemicals
that may damage the unit.
2.0 Setup Procedure
1. Remove the battery cover from the remote sensors.
2. Remove the battery cover from the monitor and insert 2 x AAA batteries according to the
correct polarity.
3. Move the CH slide switch on the back of the remote sensor to the correct channel (1, 2 or 3).
Next insert 2 x AA batteries into the sensor.
4. The transmission indication LED will
been sent to the monitor. Once the signal is received, the dashes (--.-°C) on the monitor for
channel 1, 2 or 3 will change to the current outdoor temperature.
5. Once the monitor receives the signal from the
connect the other 2 remote sensors with the monitor.
6. If after 3 minutes the screen does not change to show the outdoor temperature, press the CH
button on the monitor to select the channel you would like to reset, CH1, CH2 or CH3 will
7. Press and hold the CH button to select it. The monitor will now attempt to search for the signal
for another 3 minutes. Press the TX button on the back of the remote sensor to force the
sensor to send out another transmission signal to the monitor.
8. Place the monitor and remote sensors within effective transmission range, which in usual
circumstances is 50 metres (164 feet). The range is affected by the building materials and where
the monitor and remote sensor are positioned; try various locations for the best results.
NOTE: The remote sensors can be placed outdoors or inside your home in different rooms. The
remote sensor should be placed in a shaded area for accurate readings.
2.1 Troubleshooting
If the outdoor temperature cannot be received, check:
1. The distance between the monitor or remote sensor should be at least 1.2 metres (4 feet) away
from any interfering sources such as computer monitors or TV sets.
2. Avoid placing the monitor onto or in the immediate proximity of metal window frames.
appears on the display replace all batteries with new ones.
on the remote sensor indicating that the signal has
sensor, follow steps 3 and 4 above to