Troubleshooting - Sealey LS370H.V2 Manual

Table of Contents

Advertisement

7. troubleSHooting

problem
Fails to split logs
The log pusher moves jerkily, making
unfamiliar noise or vibrating a lot
oil leaks around cylinder ram or from other
points
Horizontal log Splitter StanD for lS370H.V2 anD lS520H.V2
lS520HSt.V2
Model no:
8. StanD Safety
Familiarise yourself with this product, application and limitations.
9
Maintain the stand in good condition.
9
Replace or repair damaged parts. Use recommended parts only. non authorised parts may be dangerous and will invalidate the
9
warranty.
Keep the stand clean for best and safest performance.
9
ensure the wood splitter is correctly secured on the stand before commencing work activity.
9
ensure the ground is strong enough to withstand the weight of the stand, splitter and logs.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip steel toe-capped shoes/boots.
9
Keep children and unauthorised persons away from the working area.
9
Do not use the stand for any purpose other than fitting log splitter Model No. LS370H.V2 and LS520H.V2.
8
Do not make any modifications to the stand.
8
Do not use the stand if any parts are missing.
8
Do not exceed the rated capacity of the wood splitter.
8
Do not use as a platform.
8
When not in use, stand or store in a safe, dry location.
9
Warning! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that may occur.
It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be
applied by the operator.
Warning! Must only be used correct height. log splitter must be securely mounted so that the hold-to-run two-hand control device
shall be located so that the height control actuators shall be between 850 mm to 1650 mm from the ground.
9. introDuCtion
Powder coated steel frame for added corrosion resistance. suitable for attaching Model no. ls520H.V2 and ls370H.V2 Horizontal log splitter.
labour and work time are kept to a minimum by creating a suitable working height. Attaching the wheels from Model no. ls520H and ls370H
enables easy and efficient movement of the stand.
10. SpeCifiCation
Height (with log splitter): ......................................... 1250mm
Height (without log splitter): ...................................... 740mm
© Jack sealey limited
probable CauSe
log is improperly positioned.
The sizes or hardness of the log exceeds the
capacity of the machine.
Wedge cutting edge is blunt.
oil leaks.
Unauthorized adjustment was made on Max.
Pressure limiting screw. lower max pressure
rating was set.
lack of hydraulic oil and excessive air in the
hydraulic system.
Air sealed in hydraulic system while
operating.
Bleed screw is not tightened before moving
the log splitter.
oil drain Bolt with dipstick is not tight.
Hydraulic Control Valve Assembly and / or
seal(s) worn.
Original Language Version
remeDy SuggeSteD
Refer to "log splitter operation" section for
perfect log loading.
Reduce the log sizes before splitting it on the
log splitter.
Refer to "Sharpening Wedge" section to
sharpen the cutting edge.
locate leak(s) and contact the stockist.
Contact the stockist.
Check oil level for possible oil refilling.
Contact the stockist.
loosen Bleed screw by 3 ~ 4 rotations before
operating the log splitter.
Tighten the Bleed screw up before moving
the log splitter.
Tighten the oil drain Bolt with dipstick.
Contact the stockist
lS370H.V2 LS520H.V2 Issue 2 (3) 02/10/19

Advertisement

Table of Contents
loading

Subscribe to Our Youtube Channel

This manual is also suitable for:

Ls520h.v2Ls520hst.v2

Table of Contents